GB Cordless Hammer Driver Drill Instruction manual F Perceuse Percussion-Visseuse Manuel d’instructions sans Fil D Akku-Schlagbohrschrauber Betriebsanleitung I Trapano avvitatore a batteria con percussione Istruzioni per l’uso Accuschroefboorhamermachine Gebruiksaanwijzing E Rotomartillo Atornillador Inalámbrico Manual de instrucciones P Furadeira de Impacto / Parafusadeira a Bateria Manual de instruções DK Ledningsfri slagboremaskine Brugsanvisning GR Κρουστικό δραπανοκατσάβιδο μπατα
4 1 2 3 1 011830 2 012128 6 5 3 011493 4 011503 8 B A 7 5 011494 9 6 011495 13 10 11 12 7 2 011496 8 011497
14 17 15 18 16 9 011498 10 007470 002449 12 011499 19 11 21 16 20 13 006258 14 011500 22 23 15 25 24 011501 16 011502 3
26 25 17 4 006304
ENGLISH (Original instructions) Explanation of general view 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Red indicator Button Battery cartridge Star marking Switch trigger Lamp Reversing switch lever Speed change lever Action mode changing ring 19. 20. 21. 22. 23. 24. 25. 26.
9. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 10. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product.
The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery. Switch action (Fig. 3) CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
Hold the tool firmly with one hand on the grip and the other hand on the bottom of the battery cartridge to control the twisting action. Drilling operation Hammer drilling operation CAUTION: • Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. • There is a tremendous force exerted on the tool/bit at the time of hole break through.
performed by Makita Authorized Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
NEDERLANDS (Originele instructies) Verklaring van het onderdelenoverzicht 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Rode deel Knop Accu Ster-merkteken Aan/uit-schakelaar Lampje Omkeerschakelaar Snelheidsinstelknop Werkingsfunctie-keuzering 19. 20. 21. 22. 23. 24. 25. 26.
wanneer u werkt op plaatsen waar het bevestigingsmateriaal met verborgen bedrading in aanraking kan komen. Wanneer bevestigingsmaterialen in aanraking komen met onder spanning staande draden, zullen de niet-geïsoleerde metalen delen van het gereedschap onder spanning komen te staan zodat de gebruiker een elektrische schok kan krijgen. 5. Zorg er altijd voor dat u stevig staat. Zorg ervoor dat er niemand zich onder u bevindt wanneer u het gereedschap op een hoge plaats gebruikt. 6.
klikgeluid hoort. Als u het rode deel aan de bovenkant van de knop kunt zien, is de accu niet goed aangebracht. LET OP: • Breng de accu altijd helemaal aan totdat het rode deel niet meer zichtbaar is. Als u dit niet doet, kan de accu per ongeluk uit het gereedschap vallen en u of anderen in uw omgeving verwonden. • Breng de accu niet met kracht aan. Als de accu niet gemakkelijk erin kan worden geschoven, wordt deze niet goed aangebracht.
Het draaikoppel instellen (zie afb. 7) Het draaikoppel kan in 16 stappen worden ingesteld door de instelring te draaien zodat de gewenste stand op de schaalverdeling is uitgelijnd met de pijlpunt op de behuizing van het gereedschap. Het draaikoppel is minimaal wanneer stand 1 is uitgelijnd met de pijlpunt, en maximaal wanneer stand 16 is uitgelijnd met de pijlpunt.
Aanbevolen diameter voorgeboord gat (mm) 3,1 2,0 - 2,2 De koolborstels vervangen (zie afb. 13) 3,5 2,2 - 2,5 3,8 2,5 - 2,8 4,5 2,9 - 3,2 4,8 3,1 - 3,4 5,1 3,3 - 3,6 5,5 3,7 - 3,9 5,8 4,0 - 4,2 6,1 4,2 - 4,4 Vervang deze wanneer ze tot aan de slijtgrensmarkering zijn afgesleten. Houd de koolborstels schoon en zorg ervoor dat ze vrij kunnen bewegen in de houders. Beide koolborstels dienen tegelijkertijd te worden vervangen. Gebruik alleen identieke koolborstels.
Geluid ENG905-1 De typische, A-gewogen geluidsniveaus zijn gemeten volgens EN60745: Model DHP446 Geluidsdrukniveau (LpA): 80 dB (A) Onzekerheid (K): 3 dB (A) Het geluidsniveau kan tijdens gebruik hoger worden dan 80 dB (A). Model DHP456 Geluidsdrukniveau (LpA): 81 dB (A) Geluidsvermogenniveau (LWA): 92 dB (A) Onzekerheid (K): 3 dB (A) Draag gehoorbescherming.