operation manual

14 ENGLISH
Chisel angle (when chipping,
scaling or demolishing)
Thechiselcanbesecuredatthedesiredangle.To
change the chisel angle, rotate the action mode chang-
ingknobtotheOsymbol.Turnthechiseltothedesired
angle.
►Fig.14: 1.Actionmodechangingknob2. Pointer
Rotate the action mode changing knob to the
sym-
bol.Thenmakesurethatthechiselissecurelyheldin
placebyturningitslightly.
Depth gauge
Thedepthgaugeisconvenientfordrillingholesof
uniformdepth.
Press and hold the lock button, and then insert the
depthgaugeintothehexhole.
►Fig.15: 1. Depth gauge 2. Lock button
Makesurethatthetoothedsideofthedepthgauge
facesthemarking.
►Fig.16: 1. Marking 2.Toothedside
Adjustthedepthgaugebymovingitbackandforth
whilepressingthelockbutton.Aftertheadjustment,
release the lock button to lock the depth gauge.
NOTE: Make sure that the depth gauge does not
touchthemainbodyofthetoolwhenattachingit.
Dust extractor attachment
Optional accessory
Installing the dust extractor
attachment
1. Loosen the side grip on the tool.
2. Installthedustcoversothattheclawsofthedust
covertinthegroovesbetweenthetoolandtheside
grip.
►Fig.17: 1. Dust cover 2. Claw 3. Groove
3. Tightenthesidegripsecurely.
4. Setthesuitablebellowsordustcoverextension
foryourwork.Whenyouusebellows,attachthejointto
itstop.Whenyoustacktwobellows,connectthemwith
thejoint.
►Fig.18: 1.Dustcoverextension2. Dust cover
3. Joint 4. Bellows
Connecting the tool to the vacuum
cleaner
1. Attachtheholderjointtothetool,andthenattach
thehoseholdertotheholderjoint.
►Fig.19: 1.Holderjoint2. Hose holder
2. Fixthehosetothehoseholder.
►Fig.20: 1. Hose holder
NOTE:Usejoint25toconnectthehoseandthedust
coverifnecessary.
Using depth gauge for drilling
operation
Whenyoustacktwobellows,attachthedepthgauge
extensiontothedepthgauge.
►Fig.21: 1.Depthgaugeextension
Dust extractor attachment (for
hammering only)
Optional accessory
1. Install the hose holder.
When the side handle is installed to tool, loosen the
clampnut,andthenremovethehexbolt.Installthe
hoseholderwiththehexboltandtheclampnutby
tighteningtheclampnutrmly.
►Fig.22: 1. Bolt 2. Hose holder 3. Clamp nut
When the side grip is installed to the tool, loosen the
sidegrip,mountthehoseholdertotheshaft,andthen
tightenthesidegriprmly.
►Fig.23: 1. Hose holder 2.Shaft3.Sidegrip
2. Attachtheholderjointtothetool,andthenattach
thehoseholdertotheholderjoint.
►Fig.24: 1.Holderjoint2. Hose holder
3. Attachthedustcoverandthehosetothetool,and
thenxthehosetothehoseholders.
►Fig.25: 1. Dust cover 2. Hose 3. Hose holder
4. Connectthehosetothehoseofthevacuum
cleanerwiththehosejoint.
NOTE:Ifthehoseisnotincluded,attachthedust
covertothecleaner'sjointorattachittoMakita's
hose ø28.
5. Adjustthedistancebetweenthedustcoverand
thetipofthechiselorbullpoint.Therecommended
distance is 30 mm to 100 mm.
►Fig.26: (1) 30 mm to 100 mm
OPERATION
CAUTION: Always use the side grip (auxiliary
handle) and rmly hold the tool by both side grip
and switch handle during operations.
CAUTION: Always make sure that the work-
piece is secured before operation.
CAUTION: Do not pull the tool out forcibly
even the bit gets stuck. Loss of control may
cause injury.
NOTE:Ifthebatterycartridgeisinlowtemperature,
thetool’scapabilitymaynotbefullyobtained.Inthis
case,warmupthebatterycartridgebyusingthe
toolwithnoloadforawhiletofullyobtainthetool’s
capability.
►Fig.27