Operation Manual
8 ENGLISH
Loading staples
WARNING: When loading staples, always
make sure that the battery cartridge is removed
from the stapler.Unintentionalringmaycause
personalinjuriesandpropertydamage.
CAUTION: After loading staples, make sure
that the sub magazine is surely closed. Falling
staplesoutofthemagazinemaycauseaninjuryto
the operator or bystander, especially when working in
high locations.
1. Remove the battery cartridge.
2. Pressthelockingleverandslidethesubmaga-
zine backward.
►Fig.7: 1. Locking lever 2. Sub magazine
3. Load staples into the main magazine with their
feetfacingup.
►Fig.8: 1. Staples 2. Main magazine
4. Afterloadingstaples,pushbackthesub-maga-
zine in place until it clicks.
Toremovestaples,followtheinstallationproceduresin
reverse.
Hook
CAUTION: Do not hang the hook from the
waist belt. Dropping the stapler, which is caused by
thehookaccidentallycomingoutofplace,maycause
unintentionalringandresultinpersonalinjuries.
►Fig.9
Thehookisconvenientfortemporarilyhangingthetool.
Thiscanbeinstalledoneithersideofthetool.
Toinstallthehook,insertitintoagrooveinthetool
housing on either side and then secure it with a screw.
Toremove,loosenthescrewandthentakeitout.
►Fig.10: 1. Groove 2. Hook 3. Screw
OPERATION
Testing the safety system
WARNING: Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
►Fig.11: 1.Trigger-lockbutton2. Switch trigger
3. Contact element 4. Sub magazine
Testsafetysystemsforpossiblefaultbeforeoperation
asfollowing.
1. Unload the tool with staples and keep the sub
magazine opened.
2. Install the battery cartridge.
3. Only pull the switch trigger without touching the
contact element against the material.
4. Only touch the contact element against the mate-
rial without pulling the switch trigger.
Ifthetooloperatesinthecaseof3and4above,the
safetysystemsarefaulty.Stopusingthetoolimmedi-
ately and ask your local service center.
Driving staples
WARNING: Until driving staples completely,
always make sure that the contact element placed
rmly on the material.Unintentionalringmay
causepersonalinjuries.
►Fig.12: 1. Switch trigger 2. Contact element 3. Front
part 4. Rear part
Youcanoperatethetoolineitherwayof“single
sequentialactuation”or“contactactuation”.
Single sequential actuation:
Inthismode,youcandriveonestaplebyonesequen-
tial operation.
1. Placeatthecontactelementonthematerial.
2. Holdbothofthefrontpartandtherearpartofthe
toolrmlyagainstthematerial.
3. Pulltheswitchtriggerfullytodrivethestaples.
4. Releaseyourngerfromtheswitchtriggerbefore
movethecontactelementfromthematerial.
Contact actuation:
In this mode, you can drive staples repetitively.
1. Pulltheswitchtrigger.
2. Withtheswitchtriggerpulled,placeatthecon-
tact element on the material to drive the staples.
3. Movethetooltothenextareaandplaceatthe
contact element on the material again.
NOTE:Thegrooveindicatesthepointthatstapleis
driven.
►Fig.13: 1. Groove
Whentheheadofdrivenstapleremainsabovethe
workpiecesurface,drivethestaplewhileholdingthe
staplerheadrmly.
►Fig.14
Thematerialmaybeunsuitable,iftheheadofdriven
stapleremainsabovetheworkpiecesurfacealthough
thestaplerheadisheldrmly.
NOTE: Using the stapler continuously with the head
ofdrivenstaplesremainingabovethesurfaceof
materialmaycausedamagetothedriverofthesta-
plerandstaplerjammingetc.
Anti dry re mechanism
WARNING: When loading staples, always
make sure that the battery cartridge is removed
from the stapler.Unintentionalringmaycause
personalinjuriesandpropertydamage.
Thistoolisequippedwithanantidryremechanism.
Whenthenumberofremainingstaplesinthemagazine
becomes 5 - 8 pcs., the switch trigger can no longer be
pulled.Atthistime,insertanewstripofstaplesinthe
magazine.Theswitchtriggercanbepulledagain.