ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Impact Driver DTD134 DTD146 012010 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities DTD134 DTD146 Machine screw 4 mm - 8 mm Standard bolt 5 mm - 14 mm High tensile bolt 5 mm - 12 mm No load speed (min-1) 0 - 2,400 0 - 2,300 Impacts per minute 0 - 3,200 Overall length 138 mm Net weight 1.2 kg (with battery BL1415/BL1415N) 1.4 kg (with battery BL1430/BL1440) 1.3 kg (with battery BL1815/BL1815N/BL1820) 1.5 kg (with battery BL1830/BL1840/BL1850) Rated voltage D.C.14.4 V D.C.
Electrical safety 4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 5. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 6. Do not expose power tools to rain or wet conditions.
coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Service 28.
2. 3. Do not disassemble battery cartridge. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
When the tool is overloaded: At this time, release the switch trigger, remove the battery cartridge and remove causes of overload and then pull the switch trigger again to restart. When battery cells get hot: If any operation of the switch trigger, the motor will remain stopped. At this time, stop use of the tool and cool or charge the battery cartridge after removing it from the tool. When the remaining battery capacity gets low: If any operation of the switch trigger, the motor will remain stopped.
For tool with deep bit hole LED indicator status Remaining battery capacity A=17mm B=14mm About 50% or more A=12mm B=9mm About 20% - 50% To install these types of bits, follow the procedure (1). To install these types of bits, follow the procedure (2). (Note) Bit-piece is necessary for installing the bit. 011405 1. About less than 20% To install the bit, pull the sleeve and insert the bit into the sleeve as far as it will go. 012023 1. Bit 2.
High tensile bolt Nm (kgf cm) 120 (1,224) 1. Hook 2. Screw M12 (M12) 1 Fastening torque 100 (1,020) 2 012014 The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. (M14) (M12) (M10) (M8) Proper fastening torque Fastening torque 1.0 2.0 3.
4. The manner of holding the tool or the material of driving position to be fastened will affect the torque. Operating the tool at low speed will cause a reduction in the fastening torque. 5. Raise the arm part of the spring and then place it in the recessed part of the housing with a slotted bit screwdriver of slender shaft or the like. 1.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885243B229 12 www.makita.
