Instructions

12 ENGLISH
NOTICE: Before using the powder lter, make
sure that prelter and damper are always used
together. It is not allowed to install powder lter solely.
Installing the water lter
Optional accessory for cloth lter model
CAUTION: Never pick up water or wet dust with-
out the oat and the cloth lter or the water lter.
CAUTION: For picking up wet dust, make sure that
the oat cage and the oat are installed on the cleaner.
CAUTION: When installing the water lter on
the tank, set it tight at the opening of the tank so
that the hook of the water lter engages the tank
opening rmly and there is no space between the
water lter and the tank.
To pick up water or wet dust only, the water lter is more
suitable than the cloth lter.
When installing the water lter, align its mounting posi-
tion mark with the one on the tank.
► Fig.15: 1. Water lter 2. Tank 3. Mounting position
marking
NOTE: It is recommended using water lter when
picking up large amount of water repeatedly.
Otherwise vacuum ability may be reduced in case of
cloth lter.
Installing the paper pack
Optional accessory
WARNING: When using the paper pack, also
use the cloth lter or prelter together that is
preinstalled on the cleaner. Failure to use the cloth
lter / prelter together may cause unusual noise and
heat, resulting in a re.
CAUTION: (For the cloth lter model)
• Never pick up water or other liquids or wet
dusts when using the paper pack. Picking
up such things may cause the paper pack
breakage.
• Before using the paper pack, make sure that
powder lter (optional accessory), damper
(optional accessory) and prelter are always
used together.
CAUTION: (For the powder lter model)
• Before using the paper pack, make sure
that powder lter, damper and prelter are
always used together.
1. Remove the rubber holder.
► Fig.16: 1. Rubber holder
2. Extend the paper pack.
3. Align the paper pack opening with the dust suction
opening of the cleaner.
4. Insert the cardboard of the paper pack onto the
holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.17: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it between
the holder plate and the tank, and pull it to the hose inlet.
► Fig.18: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the cloth
lter / prelter edge can catch and hold the bag securely.
► Fig.19: 1. Cloth lter / prelter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
Emptying the polyethylene bag
WARNING: Always make sure that the cleaner
is switched off, unplugged, and the battery car-
tridge is removed before emptying the polyeth-
ylene bag. Failure to do so may cause an electric
shock and serious personal injury.
CAUTION: Do not apply a great impact on the
oat cage and tank. Applying a great impact may
cause deformation and damage to the parts.
CAUTION: Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. Or, the suction force will weaken and the
motor may be broken.
CAUTION: Do not grab the hook when empty-
ing the tank. Grabbing the hook may cause the hook
to break.
Unhook and lift up the tank cover.
Shake off the dust from the cloth lter / prelter and then
take the polyethylene bag out of the tank.
► Fig.20
NOTE: Take the polyethylene bag carefully out of the
tank so that the polyethylene bag cannot be caught
and torn by the protrusion inside the tank when emp-
tying it.
NOTE: Empty the polyethylene bag before it
becomes full. Too much dust in the tank may cause
the polyethylene bag to be torn.
Installing the tool box
1. Release the lock of the battery cover, and open
the battery cover.
2. Set the rails on the tool box along the grooves on
the housing.
3. Close the battery cover and apply the lock.
► Fig.21
The tool box is convenient for carrying batteries, exten-
sion code, pipe, or cuffs.
► Fig.22