Backpack BrushCutter EBH340R INSTRUCTION MANUAL EBH340R Warning Read this instruction manual carefully before putting the Brush Cutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully!
English Thank you very much for selecting the MAKITA Brush Cutter. We are pleased to be able to you the MAKITA Brush Cutter which is the result of a long development programme and many years of knowledge and experience. Please read, understand and follow this booklet which refers in detail to the various points that will demonstrate its outstanding performance. This will assist you to safely obtain the best possible result from your MAKITA Brush Cutter. Table of Contents Page Symbols ......................
SAFETY INSTRUCTIONS General Instructions – To ensure correct and safe operation, the user must read, understand and follow this instruction manual to assure familiarity with the handling of the brush cutter. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. – It is recommended only to loan the brush cutter to people who have proven to be experienced with brush cutters. Always hand over the instruction manual.
Start the brush cutter only in accordance with the instructions. Do not use any other methods for starting the engine! – Use the brush cutter and the tools supplied only for applications specified. – Start the brush cutter engine only after the entire tool has been assembled. Operation of the tool is permitted only after all the appropriate accessories are attached! – Before starting, make sure that the cutter blade will not contact any objects such as branches, stones, etc.
Method of operation – Use the brush cutter only in good light and visibility. During cold seasons beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. – Do not overreach. Keep proper footing, balance and hand control of the unit at all times. – Never cut above waist level. – Never stand on a ladder while running the brush cutter. – never climb up into trees to perform any cutting operation with the brush cutter. – Never work on unstable surfaces or steep terrain.
Never straighten or weld damaged cutting blades. – Be kind to the environment. Operate the brush cutter with as little noise and pollution as possible. In particular check the correct adjustment of the carburetor. – Clean the brush cutter at regular intervals and check that all screws and nuts are securely tightened. – Never service or store the brush cutter in the vicinity of open flames, sparks, etc. – Always store the brush cutter in a well-ventilated locked room and with an emptied fuel tank.
TECHNICAL DATA EBH340R Model Loop handle Dimensions : length x width x height (without pipe case length) mm Mass (without guard and cutting blade) 400 x 325 x 395 kg 9.8 L 0.65 Cutting attachments (cutter blade dia.) mm 255 Engine displacement cm3 33.5 kw 1.07 at 7000 min-1 Volume (fuel tank) Maximum engine performance Engine speed at recommended max.
DESIGNATION OF PARTS Ԡ Ԝ ԟ Ԟ ԛ ԥ ԡ ԣ Ԣ Ԥ Ԛ ԝ ԩ Ԩ Ԫ ԧ ԫ Ԧ Ԙ ԙ 8 GB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DESIGNATION OF PARTS Fuel Tank Rewind Starter Air Cleaner I-O Switch (on/off) Spark Plug Exhaust Muffler Handle Control Lever Control Cable Shaft Protector Gear Case/Head Case Cutter Blade Shoulder Strap Fuel Filter Cap Starter Knob Primmer Pump Choke Lever Exhaust Pipe Oil Gauge Flexible Pipe Grip
ASSEMBLY OF ENGINE AND DRIVE SHAFT CAUTION : Before performing any work on the brush cutter, always switch off the motor and pull the spark plug connectors off the spark plug. Beware of hot engine pars and sharp blade edges. Always wear protective gloves! CAUTION : Start the brush cutter only after having assembled it completely. 1. Joining flexible pipe with engine and pipe case holder Insert on end of a flexible pipe (1) into a clutch housing (2) on an engine until it locks with a slight “click” noise.
CONNECTION OF SWITCH CORD – Connect the switch cords to the two cords from the engine by inserting one into the other. – Fix the cord connector by clamp (7). ADJUSTMENT OF CONTROL CABLE – Adjust the control cable by adjusting bolt so that it will have 1 to 2 mm play when the throttle lever is set to the low-speed position by carburetor adjusting bolt. (Be careful that the cutter blade will not turn in idling.
MOUNTING OF HANDLE – Fix the loop handle to the drive shaft by 2 bolts firmly. – Do not adjust position of the loop handle too close to the control grip. Keep not less than 25cm distance between the handle and the grip. t ine ng e o MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/protector combinations as indicated in the table must be used. Failure to do so may result in serious injury or death to user or bystanders. Be sure to use genuine MAKITA cutter blade.
BEFORE START OF OPERATION Inspection and Refill of Engine Oil – Perform the following procedure, with the engine cooled down. – While keeping the engine level, remove the oil gauge, and confirm that the oil is filled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular with the oil gauge remaining inserted in the crankcase without screwing-in (Fig. 1), refill new oil near the port (Fig. 2).
REFUELING Handling of Fuel It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still irritated, consult your doctor.
POINTS IN OPERATION AND HOW TO STOP Observe all applicable accident prevention regulations! STARTING Move at least 3m away from the place of refuelling. Place the brush cutter on a clean piece of ground taking care that the cutting tool does not come into contact with the ground or any other objects. Low speed (start position) A:Cold start 1) Set this machine on a flat space. 2) Move the throttle lever (1) to the start position (Low speed). High speed (1) 3) Choke lever Close the choke lever.
Note: – If the starter handle is pulled repeatedly when the choke lever remains at "CLOSE" position, the engine will not start easily due to excessive fuel intake. – In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also, dry the electrode section of the spark plug. Caution during operation: If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000rpm or more.
SERVICING INSTRUCTIONS CAUTION : Before doing any work on the brush cutter, always stop the engine and pull the plug cap off the spark plug (see "checking the spark plug"). Always wear protective gloves! To ensure a long service life and to avoid any damage to the equipment, the following servicing operations should be performed at regular intervals. Daily checkup and maintenance – Before operation, check the machine for loose screws or missing parts.
5) Keep the engine level, and feed new oil up to the edge of the oil refill port. In refill, use a lubricant refill container. 6) After refill, securely tighten the oil gauge. Insufficient tightening of the oil gauge will lead to oil leakage. POINTS ON OIL – Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the relevant laws and regulations. For any points remaining unknown, contact Authorized Service Agent.
SUPPLY OF GREASE TO GEAR CASE Grease case – Supply grease (Shell Alvania 2 or equivalent) to the gear case through the grease hole every 30 hours. (Genuine MAKITA grease may be purchased from your MAKITA dealer.
STORAGE WARNING: When draining the fuel, be sure to stop the engine and confirm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire. ATTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the fuel tank and carburetor, and keep it at a dry and clean place.
Operating time Before After operation lubrication Item Inspect/clean Daily (10h) 30h 50h 200h Shutdown Corres-po /rest nding P ٤ 13 Engine oil ٤ *1 Replace Tightening parts (bolt, nut) 17 Inspect ٤ 19 Clean/inspect ٤ ̆ Fuel tank ٤ *3 Drain fuel 20 Throttle lever Check function ٤ 15 Stop switch Check function ٤ 15 Cutting blade Inspect Low-speed rotation ٤ ٤ 12 Inspect/adjust ٤ 16 Air cleaner Clean ٤ 18 Ignition plug Inspect ٤ 18 Cooling air duct Clean/inspect
TROUBLESHOOTING Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership. State of abnormality Probable cause (malfunction) Remedy Failure to operate primer pump Push 7 to 10 times. Low pulling speed of starter rope Pull strongly. Lack of fuel Feed fuel.
MEMO
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan 6119522700 08.