EBH341U/EBH341L GB Petrol Brushcutter F Débroussailleuse thermique D Motorsense I Decespugliatore a benzina NL Benzinebosmaaier E Desbrozadora P Roçadeira a gasolina DK Benzindrevet buskrydder GR Βενζινοκίνητο Θαμνοκοπτικό ORIGINAL INSTRUCTION MANUAL MANUEL D’INSTRUCTIONS ORIGINAL ORIGINALBEDIENUNGSANLEITUNG MANUALE DI ISTRUZIONI ORIGINALE ORIGINELE GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ORIGINAL MANUAL DE INSTRUÇÕES ORIGINAL ORIGINAL BRUGSANVISNING ΑΡΧΙΚΟ ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ EBH341U E
Important: Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully! Important : Veuillez lire attentivement ce mode d'emploi avant d'utiliser la débroussailleuse thermique, et observez strictement les consignes de sécurité ! Veillez à conservez ce mode d'emploi ! Wichtig: Lesen Sie vor Verwendung der Motorsense diese Bedienungsanleitung aufmerksam durch und halten Sie die Sicherheitsregeln
English Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points that will demonstrate its outstanding performance. This will assist you to obtain the best possible result from your MAKITA Petrol Brushcutter. Table of Contents Page Symbols..............................
SAFETY INSTRUCTIONS General Instructions – To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol Brushcutter. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. – It is recommended only to lend the Petrol Brushcutter to people who have proven to be experienced with Petrol Brushcutters. Always hand over the instruction manual.
Start the Petrol Brushcutter only in accordance with the instructions. – Do not use any other methods for starting the engine! – Use the Petrol Brushcutter and the tools only for such applications as specified. – Only start the Petrol Brushcutter engine, after the entire assembly is done. Operation of the device is only permitted after all the appropriate accessories are attached! – Before starting make sure that the cutting tool has no contact with hard objects such as branches, stones etc.
Method of operation – Only use the Petrol Brushcutter in good light and visibility. During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. – Never cut above waist height. – Never stand on a ladder and run the Petrol Brushcutter. – Never climb up into trees to perform cutting operation with the Petrol Brushcutter. – Never work on unstable surfaces. – Remove sand, stones, nails etc. found within the working range.
Never straighten or weld damaged cutting tools. – Operate the Petrol Brushcutter with as little noise and contamination as possible. In particular check the correct setting of the carburetor. – Clean the Petrol Brushcutter at regular intervals and check that all screws and nuts are well tightened. – Never service or store the Petrol Brushcutter in the vicinity of naked flames. – Always store the Petrol Brushcutter in locked rooms and with an emptied fuel tank.
TECHNICAL DATA EBH341U, EBH341L Model Dimensions: length x width x height (without cutting blade) Mass (without plastic guard and cutting blade) mm kg EBH341U EBH341L Bike handle Loop handle 1,810 x 620 x 500 1,810 x 330 x 275 7.1 6.7 Volume (fuel tank) L 0.65 Volume (oil tank) L 0.1 3 33.5 Engine displacement Maximum engine performance cm ISO8893 1.07 at 7,000 min-1 kw Maximum rotational frequency of the spindle min-1 6,850 Engine speed at recommended max.
DESIGNATION OF PARTS EBH341U ⑤ ⑨ ④ ⑪ ⑫ ⑤ ⑦ ⑯ ⑫ ④ ⑩ ⑨ ⑩ ⑬ ⑦ ⑪ ⑮ ⑰ ⑬ ⑭ ⑮ EBH341L ⑭ ⑱ GB DESIGNATION OF PARTS 1 Fuel Tank 2 Rewind Starter 3 Air Cleaner 4 I-O Switch (on/off) 5 Spark Plug 6 Exhaust Muffler 7 Clutch Case 9 Hanger 10 Handle 11 Throttle Lever 12 Control Cable 13 Shaft 14 Protector 15 Gear Case/Head Case 16 Handle Holder 17 Cutter Blade 18 Nylon Cutting Head 19 Fuel Filler Cap 20 Starter Knob 21 Primmer Pump 22 Choke Lever 23 Exhaust
MOUNTING OF HANDLE CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely. For machines with bike handle models – Loosen knob (1). – Place handle (4) between handle clamp (2) and handle holder (3).
MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA cutter blades or nylon cutting head. Metal blade Protector for metal blades Nylon cutting head Protector for nylon cutting head – The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately.
MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily. – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench. – Loosen the nut (1) (left-hand thread) with the socket wrench and remove the nut (1), cup (2), and clamp washer (3). (4) Hex wrench (3) (2) (1) Mounting of cutterblade With the hex wrench still in place.
BEFORE START OF OPERATION Inspection and refill of engine oil – Perform the following procedure, with the engine cooled down. – While keeping the engine level, remove the oil gauge, and confirm that the oil is filled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular with the oil gauge remaining inserted in the crankcase without screwing-in (Fig. 1), refill new oil near the port (Fig. 2).
REFUELING Handling of fuel It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufficiently ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still irritated, consult your doctor.
CORRECT HANDLING OF MACHINE Attachment of shoulder strap – Adjust the strap length so that the cutter blade will be kept parallel with the ground. Buckle For EBH341U NOTE: Be careful not to trap clothing, etc., in the buckle. EBH341U Detachment For EBH341L – In an emergency, push the notches (1) at both sides, and you can detach the machine from you. Be extremely careful to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity.
4) Primer pump Continue to push the primer pump until fuel enters into the primer pump. (In general, fuel enters into the primer pump by 7 to 10 pushes.) If the primer pump is pushed excessively, an excess of gasoline returns to the fuel tank. Carburetor Primer Pump 5) Recoil starter Pull the start knob gently until it is hard to pull (compression point). Then, return the start knob, and pull it strongly. Never pull the rope to the full.
Operation of Throttle Lever With the throttle lever main unit held by hand (with the lock-off lever pushed), pull the throttle lever and the engine rotation will be increased. Release the throttle lever, and the engine will run idle again. Release the hand from the throttle lever main unit, and the lock-off lever will return automatically so that the throttle lever will not be pulled by mistake.
Replacing the nylon cord 1. Put off cover from housing, pressing two cover locking tabs located oppositely on side of the housing. Pull up Cover Locking Tab Housing Window 2. Take off tap knob and spool from the housing. Spool Tab knob 3. Put each one end of two cutting lines into each holes at inner most of the slot on one of spool outer flanges. Put the lines into spool gutters through each slit on the flanges. 4.
7. Put in the cutting lines through the slot of eyelets. 8. Put the cover onto the housing, aligning the tabs on cover and the windows on housing. Make sure the cover is secured exactly to the housing. Outer edge of cover locking tab and outer surface of the housing should be on same circumference.
In replacement, perform the following procedure. 1) Confirm that the tank cap is tightened securely. 2) Detach the oil gauge. Keep the oil gauge free from dust or dirt. Fuel tank cap Oil gauge 3) Place waste or paper near the oil refill port. Waste or paper 4) Detach the oil gauge, and drain oil, tilting the main unit toward the oil refill port. Drain oil in a container for orderly disposal. 5) Keep the engine level, and feed new oil up to the edge of the oil refill port.
CLEANING OF AIR CLEANER DANGER: INFLAMMABLES STRICTLY PROHIBITED Element (sponge) Interval of Cleaning and Inspection: Daily (every 10 operating hours) – Turn the choke lever to the full close side, and keep the carburetor off from dust or dirt. – Remove the air cleaner cover-fixing bolts. – Pull the cover lower side and detach the air cleaner cover. – If oil adheres to the element (sponge), squeeze it firmly.
CLEANING OF FUEL FILTER WARNING: INFLAMMABLES STRICTLY PROHIBITED Interval of Cleaning and Inspection: Monthly (every 50 operating hours) Fuel filter (1) House clamp Fuel pipe Suction head in the fuel tank – The fuel filter (1) of the suction head is used to filler the fuel required by the carburetor. – A periodical visual inspection of the fuel filter is to be conducted. For that purpose open the tank cap, use a wire hook and pull out the suction head through the tank opening.
STORAGE WARNING: When draining the fuel, be sure to stop the engine and confirm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inflammability and fire. ATTENTION: W hen the machine is kept out of operation for a long time, drain up all fuel from the fuel tank and carburetor, and keep it at a dry and clean place.
Item Operating time Engine oil Tightening parts (bolt, nut) Fuel tank Before After operation lubrication Daily (10h) 30h 50h 200h Shutdown/ Corresrest ponding P Inspect/clean 13 Replace *1 19 Inspect 22 Clean/inspect — Drain fuel *3 23 Throttle lever Check function — Stop switch Check function 16 Cutting blade Inspect 11 Low-speed rotation Inspect/adjust 17 Air cleaner Clean 21 Ignition plug Inspect 21 Cooling air duct Clean/inspect 22 Inspect 22 Fuel pipe Replac
TROUBLESHOOTING Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership.
Français Merci pour votre achat de cette débroussailleuse thermique de MAKITA. Nous sommes ravis de vous proposer la débroussailleuse thermique de MAKITA, résultat d’un long programme de développement et de nombreuses années d’expérience et de connaissances. Veuillez lire ce livret qui explique en détails les nombreuses caractéristiques qui en font un outil d’une performance exceptionnelle. Il vous aidera à obtenir le meilleur résultat possible avec votre débroussailleuse thermique de MAKITA.
CONSIGNES DE SÉCURITÉ Instructions générales – Pour vous assurer d’une utilisation correcte, lisez ce mode d’emploi pour vous familiariser avec le fonctionnement de la débroussailleuse thermique. Sans ces informations, vous risquez de vous mettre en danger ou de blesser d’autres personnes à cause d’une utilisation incorrecte. – Nous vous recommandons de prêter la débroussailleuse thermique uniquement à des personnes qui ont de l’expérience avec les débroussailleuses thermiques.
Ne démarrez la débroussailleuse thermique qu’en conformité avec les instructions. – N’utilisez pas d’autre méthode pour démarrer le moteur ! – Utilisez uniquement la débroussailleuse thermique et les outils pour les usages indiqués. – Ne démarrez le moteur de la débroussailleuse thermique qu’après que l’équipement ait été entièrement assemblé.
Mode d’emploi – N’utilisez la débroussailleuse thermique qu’avec une bonne visibilité et un bon éclairage. Pendant l’hiver, soyez attentifs aux zones glissantes ou mouillées, au verglas et à la neige (risques de glissade). Assurez-vous toujours d’avoir une bonne stabilité. – Ne coupez jamais à une hauteur supérieure aux épaules. – Ne montez jamais sur une échelle pour utiliser la débroussailleuse thermique. – Ne grimpez jamais dans les arbres pour utiliser la débroussailleuse thermique.
Ne jamais redresser ou souder des dispositifs de coupes endommagés. – Utilisez la débroussailleuse thermique avec aussi peu de bruit et de contamination que possible. Vérifiez notamment le bon réglage du carburateur. – Nettoyez la débroussailleuse thermique à des intervalles réguliers et vérifiez que toutes les vis ainsi que les écrous sont bien serrés. – N’entretenez ni stockez jamais la débroussailleuse thermique à proximité de flammes.
DONNÉES TECHNIQUES DE L’EBH341U, EBH341L Modèle Dimensions : longueur x largeur x hauteur (sans la lame de coupe) Masse (sans la protection plastique et la lame de coupe) mm kg EBH341U EBH341L Poignée de vélo Poignée fermée 1 810 x 620 x 500 1 810 x 330 x 275 7,1 6,7 Volume (réservoir d’essence) L 0,65 Volume (réservoir d’huile) L 0,1 Déplacement du moteur Performance du moteur maximum cm ISO8893 33,5 3 1,07 à 7 000 min-1 kw Fréquence maximale de rotation du moteur min-1 6 850 Vites
NOMENCLATURE DES PIÈCES EBH341U ⑤ ⑨ ④ ⑪ ⑫ ⑤ ⑦ ⑯ ⑫ ④ ⑩ ⑨ ⑩ ⑬ ⑦ ⑪ ⑮ ⑰ ⑬ ⑭ ⑮ EBH341L ⑭ ⑱ F 32 NOMENCLATURE DES PIÈCES 1 Réservoir de carburant 2 Démarreur à rappel 3 Filtre à air 4 Interrupteur E-S (marche/arrêt) 5 Bougie d’allumage 6 Pot d’échappement 7 Carter d’embrayage 9 Crochet de suspension 10 Poignée 11 Levier d’accélération 12 Câble de contrôle 13 Arbre 14 Protecteur 15 Boîte d’engrenage/Boîte de la tête 16 Support de poignée 17 Couteau 18 Tête à fil
MONTAGE DE LA POIGNÉE ATTENTION : Avant de faire un travail quelconque sur la débroussailleuse thermique, il faut toujours arrêter le moteur et débrancher le connecteur des bougies. Portez toujours des gants de protection ! ATTENTION : Démarrez la débroussailleuse thermique après l’avoir entièrement montée. Pour les modèles d’outils avec poignées de vélo – Devissez le bouton (1). – Placez la poignée (4) entre le boulon de serrage (2) et le support de poignée (3).
MONTAGE DU DISPOSITIF DE PROTECTION Pour répondre aux instructions de sécurité applicables, seules les combinaisons d’outil/protections indiquées dans le tableau doivent être utilisées. Utilisez toujours des couteaux ou têtes à fil de nylon d’origine MAKITA. Lame métallique Dispositif de protection pour les lames métalliques Tête à fils de nylon Protection pour tête à fils de nylon – Le couteau doit être bien aiguisé, et sans fissures ou cassures.
MONTAGE DU COUTEAU OU DE LA TÊTE À FIL EN NYLON Tournez la machine la tête en bas pour pouvoir remplacer le couteau ou la tête à fil de nylon facilement. – Insérez la clé hexagonale à travers le trou dans la boîte d’engrenage et tournez la rondelle de réception (4) jusqu’à ce qu’elle soit verrouillée avec la clé hexagonale. – Desserrez l’écrou (1) (filetage gauche) avec la clé à douille, et enlevez l’écrou (1), la bague (2) et la rondelle de serrage (3).
AVANT DE COMMENCER Inspection et remplissage de l’huile du moteur – Suivez la procédure suivante, lorsque le moteur est froid. – En conservant le moteur à plat, retirez la jauge d’huile, puis confirmez que le niveau d’huile se situe entre les limites haute et basse.
FAIRE LE PLEIN D’ESSENCE Maniement de l’essence Veillez à manipuler l’essence avec la plus grande attention. Elle peut contenir des substances similaires à des solvants. Pour faire le plein, placez-vous dans une pièce suffisamment ventilée ou à l’extérieur. N’inhalez jamais les vapeurs d’essence, et restez à distance du carburant. En cas de contact répété ou prolongé de votre peau avec de l’essence, elle peut se dessécher, ce qui pourrait causer des maladies de peau ou des allergies.
MANIEMENT CORRECT DE LA MACHINE Attachement du harnais – Réglez la longueur de sangle de sorte que le couteau soit gardé parallèle au sol. Boucle Pour EBH341U REMARQUE : V eillez à ne pas coincer vos vêtements etc. dans la boucle. EBH341U Détachement Pour EBH341L – En cas d’urgence, appuyez sur les entailles (1) des deux côtés pour vous séparer de la machine. Faites très attention de conserver le contrôle de la machine à ce moment-là.
4) Poire d’amorçage Continuez à pousser la poire d’amorçage jusqu’à ce que le carburant pénètre dans la poire d’amorçage. (En général, le carburant pénètre dans la poire d’amorçage après 7 à 10 pressions.) Si vous poussez trop la poire d’amorçage, un surplus de carburant retourne au réservoir d’essence. Carburateur Poire d’amorçage 5) Démarreur Tirez doucement le bouton du démarreur, jusqu’à ce qu’il résiste (point de compression).
Maniement du levier d’étranglement En tenant à la main le bloc principal du levier d’étranglement (avec le levier de verrouillage enfoncé), levez le levier d’étranglement pour augmenter la vitesse de rotation du moteur. Relâchez-le pour que le moteur repasse au ralenti. Relâchez la main du bloc principal du levier d’étranglement : le levier de verrouillage retournera automatiquement à sa position initiale afin que le levier d’étranglement ne puisse pas à être activé par erreur.
Remplacement du fil en nylon 1. Enlevez le capot de son logement en appuyant sur les deux boutons de verrouillage du capot situés de part et d’autre du bloc. Tirez vers le haut Bouton de verrouillage du capot Fente du bloc 2. Otez le bouton à engrenages et la bobine du bloc. Bobine Bouton de verrouillage 3. Placez chacune des deux extrémités du fil de coupe dans un trou situé au fond de la fente sur l’un des rebords extérieurs de la bobine.
7. Faites passer les fils de coupe à travers la fente des œillets. 8. Placez le capot dans le bloc en alignant les boutons de verrouillage du capot sur les fentes du bloc. Assurez-vous que le capot est solidement en place dans le bloc. Le bord extérieur du bouton de verrouillage du capot et la surface du bloc doivent former un aligement.
Alternativement, suivez la procédure suivante. 1) Assurez-vous que le bouchon du réservoir est bien serré. 2) Enlevez la jauge d’huile. Conservez la jauge d’huile à l’abri de la poussière et des saletés. Bouchon du réservoir d’essence Jauge d’huile 3) Placez du papier ou un carton à côté de l’orifice de remplissage d’huile. Papier ou carton 4) Enelvez la jauge d’huile et le filtre à huile en inclinant le bloc principal dans la direction de l’orifice de remplissage d’huile.
NETTOYAGE DU FILTRE À AIR DANGER : FLAMMES STRICTEMENT INTERDITES Élément (éponge) Intervalle de nettoyage et d’inspection : tous les jours (toutes les 10 heures d’utilisatino) Plateau Capot du filtre à air – Tournez le levier d’étrangleur vers le côté complètement fermé et gardez le carburateur éloigné de toute poussière ou saleté. – Retirez les boulons de fixation du couvercle du filtre à air. – Tirez la partie inférieure du couvercle et enlevez le capot du filtre à air.
NETTOYAGE DU FILTRE À ESSENCE ATTENTION : FLAMMES STRICTEMENT INTERDITES Intervalle de nettoyage et d’inspection : tous les mois (toutes les 50 heures d’utilisatino) Crépine d’aspiration dans le réservoir Filtre à essence (1) Fixation Tuyau d’alimentation – Le filtre à essence (1) de la crépine d’aspiration est utilisé pour alimenter le carburant requis par le carburateur. – Une inspection visuelle périodique du fitre à essence doit être effectuée.
ENTREPOSAGE ATTENTION : P our vidanger l’essence, veillez à arrêter le moteur et à vous assurer que le moteur ait refroidi. Juste après l’arrêt du moteur, il peut encore être chaud et provoquer des brûlures ou un incendie. ATTENTION : L orsque vous prévoyez de ne pas utiliser la machine pendant une longue période, vidangez le réservoir d’essence et le carburateur, et entreposez-le dans un endroit sec et propre.
Élément Temps d’utilisation Huile du moteur Avant Après Journalière utilisation lubrification (10 h) Réservoir de carburant 50 h 200 h Arrêt/ repos Inspecter/ nettoyer P correspondante 36 *1 Remplacez.
RÉSOLUTION DE PROBLÈMES Avant d’envoyez votre machine en réparation, vérifiez si vous pouvez régler le problème vous-même. Si vous trouvez un problème, contrôlez votre machine selon les descriptions de ce mode d’emploi. Ne démontez pas et de modifiez pas de pièce d’une manière contraire à la description. Pour toute réparation, contactez un agent d’entretien agréé ou un revendeur local.
Nederlands Hartelijk dank voor uw aankoop van deze benzinebosmaaier van MAKITA. Met trots bevelen wij u deze benzinebosmaaier van MAKITA van harte aan als resultaat van een langdurig ontwikkelingsprogramma en jarenlange kennis en ervaring. Lees deze handleiding met daarin nauwkeurige beschrijvingen van de diverse punten die zijn hoogstaande prestaties demonstreren. Hierdoor bent u in staat de best mogelijke resultaten te behalen die de benzinebosmaaier van MAKITA u kan bieden. Inhoud Pagina Symbolen.....
VEILIGHEIDSINSTRUCTIES Algemene instructies – Voor een correcte gebruik dient de gebruiker deze gebruiksaanwijzing te lezen om zichzelf bekend te maken met de juiste manier van omgaan met de benzinebosmaaier. Gebruikers die onvoldoende geïnformeerd zijn, lopen de kans zichzelf en anderen in gevaar te brengen als gevolg van onjuist omgaan met de benzinebosmaaier.
Start de benzinebosmaaier alleen in overeenstemming met de instructies. – Gebruik geen enkele andere methode om de motor te starten! – Gebruik de benzinebosmaaier en de gereedschappen uitsluitend voor de beschreven toepassingen. – Start de motor van de benzinebosmaaier alleen nadat deze volledig is gemonteerd.
Gebruiksmethode – Gebruik de benzinebosmaaier alleen bij een goede verlichting en zichtbaarheid. Wees in de winter bedacht op gladde of natte plaatsen, ijs en sneeuw (gevaar voor uitglijden). Zorg er altijd voor dat u stevig staat. – Maai nooit boven heuphoogte. – Sta nooit op een ladder terwijl u de benzinebosmaaier gebruikt. – Klim nooit in een boom om daar de benzinebosmaaier te gebruiken. – Werk nooit op een instabiele ondergrond. – Verwijder zand, stenen, spijkers, enz.
Probeer nooit beschadigde snijgarnituren recht te trekken of te lassen. – Gebruik de benzinebosmaaier met zo weinig mogelijk lawaai en vervuiling. Controleer met name de carburator op een verkeerde afstelling. – Maak de benzinebosmaaier regelmatig schoon en controleer of alle bouten en moeren stevig zijn vastgedraaid. – Onderhoud of bewaar de benzinebosmaaier niet in de buurt van open vuur. – Bewaar de benzinebosmaaier altijd in een afgesloten ruimte en met een leeggemaakte brandstoftank.
TECHNISCHE GEGEVENS - EBH341U, EBH341L Model Afmetingen: lengte x breedte x hoogte (zonder snijblad) Gewicht (zonder kunststofbeschermkap en snijblad) mm kg Volume (brandstoftank) EBH341U EBH341L Handgreep Beugelhandgreep 1.810 x 620 x 500 1.810 x 330 x 275 7,1 6,7 l 0,65 Volume (olietank) l 0,1 Cilinderinhoud 3 33,5 cm Maximaal motorvermogen ISO8893 1,07 bij 7.000 min-1 kW Maximaal astoerental min-1 6.850 Motortoerental bij aanbevolen maximaal astoerental min-1 10.
NAMEN VAN ONDERDELEN EBH341U ⑤ ⑨ ④ ⑪ ⑫ ⑤ ⑦ ⑯ ⑫ ④ ⑩ ⑨ ⑩ ⑬ ⑦ ⑪ ⑮ ⑰ ⑬ ⑭ ⑮ EBH341L ⑭ ⑱ 101 NL NAMEN VAN ONDERDELEN 1 Brandstoftank 2 Trekstartinrichting 3 Luchtfilter 4 Stopschakelaar (stoppen - bedrijf) 5 Bougie 6 Uitlaatdemper 7 Koppelingshuis 9 Bevestigingsoog 10 Handgreep 11 Gashendel 12 Gaskabel 13 Schacht 14 Beschermkap 15 Tandwielhuis 16 Handgreepbevestiging 17 Metalen snijblad 18 Nylondraad-maaikop 19 Brandstofvuldop 20 Trekstarthandgreep 21 Br
DE HANDGREEP MONTEREN LET OP: Voordat u werkzaamheden uitvoert aan de benzinebosmaaier, moet u altijd de motor uitschakelen en de bougiekap van de bougie aftrekken. Draag altijd veiligheidshandschoenen. LET OP: Start de benzinebosmaaier pas nadat deze geheel in elkaar is gezet. Voor gereedschappen met een fietsstuur-type handgreep – Draai knop (1) los. – Plaats de handgreep (4) tussen de handgreepklem (2) en de handgreepvoet (3).
DE BESCHERMKAP MONTEREN In naleving van de toepasselijke veiligheidsregels mogen uitsluitend de gereedschap/beschermkap-combinaties worden gebruikt die in de afbeelding worden aangegeven. Verzeker u ervan uitsluitend originele snijbladen of nylondraad-maaikoppen van MAKITA te gebruiken. Metalen snijblad Beschermkap voor metalen snijblad Nylondraad-maaikop Beschermkap voor nylondraad-maaikop – Het snijblad moet goed geslepen zijn en vrij zijn van barsten of breuken.
HET SNIJGARNITUUR MONTEREN Draai het gereedschap ondersteboven zodat u het metalen snijblad of de nylondraad-maaikop gemakkelijk kunt vervangen. – Steek de inbussleutel in de opening van het tandwielhuis en draai de ontvangerring (4) met de inbussleutel tot deze vergrendeld wordt. – Maak de moer (1) (met linksdraaiend schroefdraad) los met de dopsleutel en verwijder de moer (1), de beker (2) en de klemring (3).
VÓÓR HET BEGIN VAN HET WERK Controleren en bijvullen van de motorolie – Voer de volgende procedure uit bij koude motor. – Houd de motor horizontaal, verwijder de oliepeilstok en controleer of het oliepeil tussen de bovenste en onderste merktekens staat. Als het oliepeil zo laag staat dat alleen de punt van de peilstok de olie raakt, ook wanneer de oliepeilstok in het motorblok is gestoken zonder deze vast te draaien (zie afb. 1), vult u via de olievulopening nieuwe olie bij (zie afb. 2).
BRANDSTOF BIJVULLEN Omgaan met brandstof Het is noodzakelijk uiterst voorzichtig om te gaan met brandstof. Brandstof kan stoffen bevatten die ook in oplosmiddelen voorkomen. Het bijvullen van brandstof moet gebeuren in een vertrek met een voldoende goede ventilatie of in de open lucht. Adem nooit brandstofdampen in en houd afstand tot de brandstof. Als uw huid herhaaldelijk in aanraking komt met brandstof gedurende een lange tijd, wordt uw huid droog, waardoor een huidziekte of allergie kan ontstaan.
CORRECTE HANTERING De schouderriem bevestigen – Pas de lengte van de schouderriem zo aan, dat het snijblad parallel aan de grond kan worden gehouden. Gesp Voor EBH341U OPMERKING: Wees voorzichtig dat uw kleding, enz., niet verstrikt raakt in de gesp. EBH341U Losmaken Voor EBH341L – In geval van nood, druk de knoppen (1) aan beide zijkanten in zodat het gereedschap los komt van uw lichaam. Let er goed op dat u op dat moment de controle over het gereedschap behoudt.
4) Brandstofhandpomp Blijf op de brandstofhandpomp drukken tot de brandstof in de brandstofhandpomp stroomt. (Over het algemeen stroomt de brandstof in de brandstofhandpomp na 7 tot 10 keer duwen.) Als te vaak op de brandstofhandpomp wordt gedrukt, vloeit het overschot aan brandstof terug naar de brandstoftank. Carburator Brandstofhandpomp 5) Trekstartinrichting Trek voorzichtig aan de trekstarthandgreep tot u weerstand voelt (compressiepunt).
De gashendel bedienen Houd het gashendelhuis in uw hand vast (met de uit-vergrendelhendel ingeduwd) en knijp de gashendel in zodat het motortoerental toeneemt. Laat de gashendel los zodat het motortoerental afneemt. Laat het gashendelhuis los uit uw hand zodat de uit-vergrendelhendel automatisch terugveert en de gashendel niet per ongeluk kan worden ingeknepen. Het motortoerental afstellen Als u het motortoerental wilt afstellen, knijpt u de gashendel helemaal in en draait u de gasregelschijf.
De nylondaad vervangen 1. Druk de twee lippen op tegenovergestelde zijden van de behuizing in en trek de afdekking van de behuizing af. Lip van behuizing Trek eraf Opening in behuizing 2. Haal de stootknop en draadspoel uit de behuizingsnaaf. Draadspoel Stootknop 3. Steek van ieder van de twee nylondraden een uiteinde in het gaatje dat achteraan de sleuf zit in ieder van de buitenflenzen van de draadspoel. Trek de nylondraden door de sleuf in iedere buitenflens in de geulen van de draadspoel.
7. Trek de nylondraden door de gleuf van de oogjes. 8. Plaats de afdekking op de behuizing, lijn de lippen op de afdekking uit met de openingen in de behuizing. Zorg ervoor dat de afdekking nauwkeurig op de behuizing wordt bevestigd. De buitenrand van de lip van de afdekking en het buitenoppervlak van de behuizing moeten even hoog liggen.
Volg de onderstaande procedure om de olie te verversen. 1) Controleer of de brandstofvuldop stevig vastgedraaid is. 2) Draai de oliepeilstok los en trek hem eruit. Zorg ervoor dat de oliepeilstok schoon blijft. Brandstofvuldop Oliepeilstok 3) Leg absorptiepapier rondom de olievulopening. Absorptiepapier 4) Draai de oliepeilstok los, trek hem eruit, en tap de olie af door de motor te kantelen zodat de olievulopening onder zit.
HET LUCHTFILTER REINIGEN WAARSCHUWING: STRENG VERBODEN VOOR ONTBRANDBARE MATERIALEN Filterelement (spons) Achterplaat Luchtfilterkap Controle- en reinigingsinterval: Dagelijks (iedere 10 bedrijfsuren) – Zet met de chokehendel de choke helemaal dicht en houd de carburator vrij van stof of vuil. – Verwijder de bevestigingsbout van de luchtfilterkap. – Trek aan de onderrand van de luchtfilterkap en haal de luchtfilterkap eraf. – Als er olie op het filterelement (spons) zit, knijpt u deze goed uit.
HET BRANDSTOFFILTER REINIGEN WAARSCHUWING: STRENG VERBODEN VOOR ONTBRANDBARE MATERIALEN Brandstoffilter (1) Slangklem Controle- en reinigingsinterval: Maandelijks (iedere 50 bedrijfsuren) Brandstofleiding Zuigkop in brandstoftank – Het brandstoffilter (1) op de zuigkop wordt gebruikt om de brandstof die door de carburator wordt aangezogen, te filteren. – Het brandstoffilter moet regelmatig visueel worden gecontroleerd.
OPSLAG WAARSCHUWING: C ontroleer of de motor is uitgeschakeld en afgekoeld voordat u begint met het aftappen van de brandstof. Vlak na het uitschakelen van de motor, is deze nog heet en kan brandwonden, ontbranding en brand veroorzaken. LET OP: Als het gereedschap gedurende een lange tijd niet gebruikt gaat worden, tapt u alle brandstof uit de brandstoftank en carburator, en slaat u het op een droge, schone plaats op.
Item Bedrijfsuren Motorolie Vastdraaien (bouten, moeren, enz.) Brandstoftank Voor gebruik Na smeren Dagelijks (10 uur) 30 uur 50 uur 200 uur Langdurige Zie pagina opslag Inspecteren/ reinigen 105 Vervang de bougie. *1 111 Inspecteren 114 Reinigen/ inspecteren — Brandstof aftappen *3 115 Gashendel Werking controleren — Stopschakelaar Werking controleren 108 Snijblad Inspecteren 103 Laag toerental Inspecteren/ afstellen 109 Luchtfilter Reinig.
PROBLEMEN OPLOSSEN Alvorens een verzoek voor reparatie in te dienen, controleer u de storing zelf aan de hand van de onderstaande tabel. Als een probleem is gevonden, repareert u het gereedschap aan de hand van de beschrijvingen in deze gebruiksaanwijzing. Probeer nooit enig onderdeel te demonteren of repareren in strijd met de beschrijvingen. Voor reparatie neemt u contact op met een erkend servicecentrum of uw plaatselijke dealer.