Demolition Hammer MODEL HM1301 INSTRUCTION MANUAL SPEC1F ICATIONS Blows per minute 1,200 I Overall length Net weight 6 4 3 mm (25-5/16") 16.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to 15. 16. 17. 18. 19. 20. 21. see that keys and adjusting wrenches are removed from tool before turning it on, AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT. Watch what you are doing, use common sense.
For all grounded tools with American type plug. GROUNDING INSTRUCTIONS: Thistool should be grounded while i n use t o protect the operator from electric shock. The tool i s equipped with a threetonductor cord and three-prong groundingtype plug to fit the proper grounding-type receptacle. The green (or green and yellow) conductor in the cord i s the grounding wire. Never connect the green (or green and yellow) wire t o a live terminal. Your unit is for use on 115 volts and has a plug that looks like Fig.
0 Installing or removing'hull point or other bits (cold chisel, etc.) CAUTION : Always be sure that the tool i s switched off and unplugged before installing or removing the bit. Pull out and turn the tool retainer so that the boss on the tool retainer faces in the direction of the arrow. Insert the bit into the tool holder as far as it will go. Then turn the tool retainer 180 degrees to secure the bit. To remove the bit, follow the installation procedure in reverse. Fig. 1 Fig.
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. Trigger switch Fig. 1 CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the “OFF” position when released. - Demolishing . Chipping Scaling Choose the right accessories for your work. After mounting the suitable accessory and switching on the demolition hammer, l e t the mere weight of the tool itself apply pressure to the work surface. Fig.
MAINTENANCE CAUTION : ALWAYS be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. e Oiling Oiling should be performed every three hours (once a day before use). Hold the tool vertically and pull the lubrication knob three to five times. Oil in the tank should be replenished about every 20 days, presuming 3 - 4 hours’ operation daily, or when oil is out of sight through the window after placing the tool vertically. Fig.
Use the screwdriver to remove the screw holding the holder cap plate as shown in the figure. Fig. 9 Use the screwdriver to remove the brush holder cap as shown in the figure. Take out the worn brush, insert the new one and secure the brush holder cap. Fig. 1 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool-specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. Bull point 410 mm (16-118”) Part No. 751407-0 Cold chisel 36 mm (1-318”) x 4 1 0 mm (16-118“) Part No. 751207-8 Scaling chisel 100 mm ( 4 “ ) x 310 mm (12-114”) Part No.
July-16-'84 US DEMOLITION HAMMER Model HM1301 Note: The switch and other part configurations may differ from country to country.
MODEL HM1301 Nov-09-'84 SDDESCRIPTION "0" 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 2 2 I 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 3 2 1 1 2 2 1 1 1 1 1 4 4 4 1 1 I 1 1 1 4 4 2 1 1 - DESCRIPTION MACHINE MACHINE ~ ~ 1 At, US Hex Socket Head Bolt M6x16 Spring Washer 6 Rear Cover Motor Housing CORD ASSEMBLY IAssembled Cord Plug & Item 61 Cord Guard Pan Head Screw M 4 ~ 1 8(With Washer1
MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
