ENGLISH (Original instructions) INSTRUCTION MANUAL Electric Breaker HM1317C HM1307C HM1317CB HM1307CB 010282 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model HM1317C HM1307C Blows per minute HM1317CB HM1307CB 730 - 1,450 Overall length 715 mm Net weight 17.0 kg 849 mm 15.3 kg Safety class 19.1 kg 17.5 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country.
ENG216-2 Measured Sound Power Level: 101dB Guaranteed Sound Power Level: 103dB Vibration The vibration total value (tri-axial vector sum) determined according to EN60745: Work mode : chiseling function with side handle Vibration emission (ah,CHeq) : 8.5 m/s2 Uncertainty (K) : 1.
Use of dust collection can reduce dust-related hazards. Power tool use and care 17. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 18. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 19.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. FUNCTIONAL DESCRIPTION the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Wear a hard hat (safety helmet), safety glasses and/or face shield. Ordinary eye or sun glasses are NOT safety glasses. It is also highly recommended that you wear a dust mask and thickly padded gloves.
Side handle (auxiliary handle) For model HM1317C,HM1317CB only • 1. Set bolt 2. Nut 3. Side handle 1 NOTE: • Blows at no load per minute becomes smaller than those on load in order to reduce vibration under no load, but this does not show trouble. Once operation starts with a bit against concrete, blows per minute increase and get to the numbers as shown in the table. When temperature is low and there is less fluidity in grease, the tool may not have this function even with the motor rotating.
(1) For bits with a collar CAUTION: Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure. • The bit without a collar cannot be retained by the method shown in Fig.(1). To remove the bit, follow the installation procedure in reverse. 1 • 2 3 OPERATION 5 4 Chipping/Scaling/Demolition 1. Bit 2. Tool retainer 3. Tool holder 4. When the bit is inserted 5.
For model HM1307C,HM1307CB only Remove the six screws using a hex wrench and remove the rear cover. 1. Rear cover 2. Hex wrench 1 1. Crank cap cover 1 2 010289 Remove the six screws using a hex wrench and remove the rear cover. 010295 Pull out the crank cap cover in the direction of arrow and remove it. 1. Crank cap 1 1 1. Hammer grease 010290 Pull out the crank cap in the direction of arrow and remove it. 010296 Then replenish with fresh grease (60g).
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation Anjo, Aichi, Japan 884923-224 12
