Specifications

SPECIFICATIONS
GENERAL POWER TOOL SAFETY WARNINGS
Makita HM1810 Electric Breaker
Supplied by Centenary Hire. Ph: [phone]
Blows per minute: 1,100
Joules: 63
Net weight: 30kg
Overall length: 824mm
Intended Use
The tool is intended for heavy chiselling and demolition work as well as
for driving and compacting with appropriate accessories.
Power Supply
The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated on
single-phase AC supply. They are double-insulated in accordance with
European Standard and can, therefore, also be used from sockets
without an earth wire.
For public low-voltage distribution systems between 220V – 240V
Switching operations of electric apparatus cause voltage fluctuations.
The operation of this device under unfavourable mains conditions can
have adverse effects to the operation of other equipment. With a mains
impedance equal or less than 0.31 Ohms it can be presumed that
there will be no negative effects. The mains socket used for this device
must be protected with a fuse or protective circuit breaker having slow
tripping characteristics.
Noise
A typical A-weighted noise level determined according to EN60745:
Sound pressure level (LpA): 84dB(A)
Sound power level (LWA): 104dB (A)
Uncertainty (K): 2.30dB(A)
WEAR EAR PROTECTION
Vibration
The vibration total value (tri-axial vector sum) determined according to
EN60745:
Work mode: chiselling
Vibration emission (ah,CHeq): 9.0m/s
2
Uncertainty(K): 1.5m/s
2
The declared vibration emission value has been measured in
accordance with the standard test method and may be used for
comparing one tools with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power tool can differ
from the declared emission value depending on the ways in which the
tool is used.
Be sure to identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions of use
(taking account of all parts pf the operating cycle such as the times
when the tool is switched off and when it is running idle in addition to
the trigger time).
WARNING Read all safety warnings and all instructions.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains operated (corded) power
tool or battery-operated (cordless) power tool.
Work Area Safety
1. Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
2. Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
5. Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Electrical safety Damaged or
entangled cords increase the risk of electric shock.
8. When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
Personal safety
9. Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may
result in serious personal injury.
10. Use safety equipment. Always wear eye protection. Safety
equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal
injuries.
11. Avoid accidental starting. Ensure the switch is in the off-
position before plugging in. Carrying power tools with your finger
on the switch or plugging in power tools that have the switch on invites
accidents.
12. Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
13. Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations.
14. Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing, and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
15. If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and properly
used. Use of these devices can reduce dust related hazards.
Power tool use and care
16. Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed.
17. Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
18. Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
19. Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands of
untrained users.
20. Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by poorly
maintained power tools.
21. Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier to
control.