GB Cordless Hammer Driver Drill Instruction manual F Perceuse Percussion-Visseuse Manuel d’instructions sans Fil D Akku-Bohrhammer Betriebsanleitung I Trapano avvitatore a batterie con percussione Istruzioni per l’uso Accuschroefboorhamermachine Gebruiksaanwijzing E Rotomartillo Atornillador Inalámbrico Manual de instrucciones P Furadeira de Impacto / Parafusadeira a Bateria Manual de instruções DK Ledningsfri slagboremaskine Brugsanvisning GR Κρουστικό δραπανοκατσάβιδο μπαταρίας Οδη
1 4 2 3 1 2 B A 5 6 3 4 11 7 9 8 10 5 6 12 7 2 8
ENGLISH (Original instructions) Explanation of general view 1. 2. 3. 4. 5. 6. 7. 8. Red indicator Button Battery cartridge Switch trigger 9. 10. 11. 12. Reversing switch lever Speed change lever Adjusting ring Action mode changing ring Graduation Arrow Sleeve Blow-out bulb SPECIFICATIONS Model HP347D Capacities No load speed (min-1 ) Blows per minute (min-1) Overall length HP457D Concrete 10 mm 13 mm Steel 10 mm 13 mm Wood 25 mm 36 mm Wood screw 5.
IMPORTANT SAFETY INSTRUCTIONS ENC009-1 FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4.
or “1” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. CAUTION: • Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and “2” side, the tool may be damaged. • Do not use the speed change lever while the tool is running. The tool may be damaged. Selecting the action mode (Fig.
exert care when the bit begins to break through the workpiece. • A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. • Always secure small workpieces in a vise or similar hold-down device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
The technical documentation is kept by our authorised representative in Europe who is: Makita International Europe Ltd. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England 23. 8.
NEDERLANDS (Originele instructies) Verklaring van het onderdelenoverzicht 1. 2. 3. 4. 5. 6. 7. 8. Rode deel Knop Accu Aan/uit-schakelaar 9. 10. 11. 12. Omkeerschakelaar Snelheidsinstelknop Instelring Werkingsfunctie-keuzering Schaalverdeling Pijl Bus Blaasbalgje TECHNISCHE GEGEVENS Model HP347D HP457D Beton 10 mm 13 mm Staal 10 mm 13 mm Hout 25 mm 36 mm Houtschroef 5,1 mm x 63 mm Maximale dikten 6 mm Hoog (2) 0 - 1.
BEWAAR DEZE INSTRUCTIES. WAARSCHUWING: Laat u NIET misleiden door een vals gevoel van comfort en bekendheid met het gereedschap (na veelvuldig gebruik) en neem alle veiligheidsvoorschriften van het betreffende product altijd strikt in acht. VERKEERD GEBRUIK of het niet volgen van de veiligheidsinstructies in deze gebruiksaanwijzing kan leiden tot ernstig persoonlijk letsel. BELANGRIJKE VEILIGHEIDSINSTRUCTIES ENC009-1 VOOR ACCU’S 1.
schakelt en weer terugkeert naar de uit-stand nadat deze is losgelaten. Om het gereedschap in te schakelen, knijpt u gewoon de aan/uit-schakelaar in. De draaisnelheid van het gereedschap neemt toe naarmate u meer druk uitoefent op de aan/uit-schakelaar. Laat de aan/uit-schakelaar los om het gereedschap te stoppen. Werking van de omkeerschakelaar (zie afb. 3) Dit gereedschap is uitgerust met een omkeerschakelaar waarmee u de draairichting kunt omkeren.
Gebruik als schroevendraaier (zie afb. 8) Draai eerst de werkingsfunctie-keuzering zodat de pijlpunt op de behuizing van het gereedschap op het symbool staat. Stel de instelring in op het juiste draaikoppelniveau voor uw klus. Ga daarna als volgt te werk. Plaats de punt van het schroefbit in de schroefkop en oefen druk uit op het gereedschap. Start het gereedschap op lage snelheid en voer vervolgens de snelheid geleidelijk op. Laat de aan/uit-schakelaar los zodra de koppeling begint te slippen.
Geluid ENG905-1 De typische, A-gewogen geluidsniveaus zijn gemeten volgens EN60745: Model HP347D Geluidsdrukniveau (LpA): 82 dB (A) Geluidsvermogenniveau (LWA): 93 dB (A) Onzekerheid (K): 3 dB (A) Model HP457D Geluidsdrukniveau (LpA): 81 dB (A) Geluidsvermogenniveau (LWA): 92 dB (A) Onzekerheid (K): 3 dB (A) Draag gehoorbescherming.
Makita Corporation Anjo, Aichi, Japan 885011-991 ALA www.makita.