ENGLISH (Original instructions) INSTRUCTION MANUAL Rotary Hammer / Combination Hammer HR2300 HR2310T HR2600 HR2601 HR2610 HR2610T HR2611F HR2611FT 010712 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model HR2300 Concrete Capacities HR2310T HR2600 HR2601 HR2610 23 mm HR2610T HR2611F HR2611FT 26 mm Core bit 68 mm 68 mm 68 mm Diamond core bit (dry type) 70 mm 80 mm 80 mm Steel 13 mm 13 mm 13 mm Wood 32 mm 32 mm 32 mm No load speed (min-1) 0 - 1,200 Blows per minute 0 - 4,600 Overall length 356 mm 380 mm Net weight 2.7 kg 2.9 kg 361 mm 2.8 kg Safety class 2.9 kg 2.8 kg 385 mm 361 mm 385 mm 2.9 kg 2.9 kg 3.
Model HR2310T Model HR2611F Work mode : hammer drilling into concrete Vibration emission (ah,HD) : 15.5 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode : hammer drilling into concrete Vibration emission (ah,HD) : 12.0 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode : chiselling function with side grip Vibration emission (ah,CHeq) : 10.5 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode : chiselling function with side grip Vibration emission (ah,CHeq) : 9.0 m/s2 Uncertainty (K) : 1.
GEA005-3 Conforms to the following European Directives: 2006/42/EC And are manufactured in accordance with the following standards or standardised documents: EN60745 The technical documentation is kept by our authorised representative in Europe who is: Makita International Europe Ltd. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions.
22. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 23. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 24. Use the power tool, accessories and tool bits etc.
8. 9. 10. 11. 12. 13. 14. warm-up, hammering operation is difficult. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. Hold the tool firmly with both hands. Keep hands away from moving parts. Do not leave the tool running. Operate the tool only when hand-held. Do not point the tool at any one in the area when operating. The bit could fly out and injure someone seriously.
Attaching the quick change drill chuck Reversing switch action B 1. Reversing switch lever 1. Spindle 2. Quick change drill chuck 3. Change cover line 4. Change cover 1 2 A 1 3 4 011562 010722 Check the line of the quick change drill chuck shows the symbol. Grasp the change cover of the quick change drill chuck and set the line to the symbol. Place the quick change drill chuck on the spindle of the tool.
For Models HR2310T, HR2610, HR2610T, HR2611F, HR2611FT Rotation with hammering 1 When changing from the symbol mode to the symbol mode, the action mode changing knob may no longer move in the symbol position. At this time, turn the tool on or turn the chuck by hand in the symbol position and then rotate the action mode changing knob. Forcing the action mode changing knob may cause tool damage. • 1. Rotation with hammering 2.
The bit can be secured at the desired angle. To change the bit angle, rotate the action mode changing knob to the O symbol. Turn the bit to the desired angle. Rotate the action mode changing knob to the symbol. Then make sure that the bit is securely held in place by turning it slightly. Installing or removing the bit 1. Bit shank 2. Bit grease 2 1 003150 Clean the bit shank and apply bit grease before installing the bit. 1.
Installing or removing the dust cup 1. Lock button 1 1 2 1. symbol 2. Grooves 3. Dust cup 3 010718 Adjust the depth gauge to the desired depth by moving it back and forth while pressing the lock button. After the adjustment, release the lock button to lock the depth gauge. 2 1 011506 Before installing the dust cup, remove the bit from the tool if installed on the tool. Install the dust cup (accessory) on the tool so that the symbol on the dust cup is aligned with the grooves in the tool. 1.
OPERATION 1. Inside periphery 2. Carved side 3. Attachment 4. Cap 5. Groove 1 2 4 Always use the side grip (auxiliary handle) and firmly hold the tool by both side grip and switch handle during operations. Hammer drilling operation 3 5 012895 1. Cap 2. Attachment 1 010729 Set the action mode changing knob to the symbol. Position the bit at the desired location for the hole, then pull the switch trigger. Do not force the tool. Light pressure gives best results.
After drilling the hole, use the blow-out bulb to clean the dust out of the hole. Chipping/Scaling/Demolition 2 1. Spindle 2. Quick change drill chuck 3. Change cover line 4. Change cover 1 For Models HR2310T, HR2610, HR2610T, HR2611F, HR2611FT 3 4 011562 Use the quick change drill chuck as standard equipment. When installing it, refer to "changing the quick change chuck for SDS-plus " described on the previous page. 1. Sleeve 2. Ring 3.
Diamond core drilling OPTIONAL ACCESSORIES When performing diamond core drilling operations, always set the change lever to the position to use "rotation only" action. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
Makita Corporation Anjo, Aichi, Japan 884939A229 16 www.makita.
