ENGLISH (Original instructions) INSTRUCTION MANUAL Combination Hammer HR3540C HR3541FC 008719 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH (Original instructions) SPECIFICATIONS Model Concrete HR3540C HR3541FC Tungsten-carbide tipped bit 35 mm Core bit 90 mm Capacities Steel 13 mm Wood 32 mm No load speed (min-1) 315 - 630 Blows per minute 1,650 - 3,300 Overall length 439 mm Net weight 5.2 kg Safety class 5.6 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
ENG215-2 Vibration The vibration total value (tri-axial vector determined according to EN60745: Work mode : chiseling function Vibration emission (ah,CHeq) : 9.0 m/s2 Uncertainty (K) : 1.5 m/s2 30th January 2009 sum) 000230 Tomoyasu Kato Director Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN ENG303-2 Work mode : hammer drilling into concrete Vibration emission (ah,HD) : 11.0 m/s2 Uncertainty (K) : 1.
must be repaired. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 22.
. 6. 7. 8. 9. 10. 11. 12. 13. 14. FUNCTIONAL DESCRIPTION highly recommended that you wear a dust mask and thickly padded gloves. Be sure the bit is secured in place before operation. Under normal operation, the tool is designed to produce vibration. The screws can come loose easily, causing a breakdown or accident. Check tightness of screws carefully before operation. In cold weather or when the tool has not been used for a long time, let the tool warm up for a while by operating it under no load.
Speed change Rotation only 1. Adjusting dial 2 1. Lock button 2. Change lever 3. Pointer 3 1 1 008538 008600 The revolutions and blows per minute can be adjusted just by turning the adjusting dial. The dial is marked 1 (lowest speed) to 5 (full speed). Refer to the table below for the relationship between the number settings on the adjusting dial and the revolutions/blows per minute. For drilling in wood or metal, materials, etc.
Indicator lamp Installing or removing the bit 1. Power-ON indicator lamp (green) 2. Service indicator lamp (red) 1 1. Bit shank 2. Bit grease 2 1 2 008541 003150 The green power-ON indicator lamp lights up when the tool is plugged. If the indicator lamp does not light up, the main cord or the controller may be defective.
clogged with chips or particles. Instead, run the tool at an idle, then remove the bit partially from the hole. By repeating this several times, the hole will be cleaned out and normal drilling may be resumed. The bit can be secured at 24 different angles. To change the bit angle, depress the lock button and rotate the change lever so that the pointer points to the symbol. Turn the bit to the desired angle. Depress the lock button and rotate the change lever so that the pointer points to the symbol.
longer tool life. Run the tool for several minutes to warm it up. Switch off and unplug the tool. Loosen the four screws and remove the handle. Note that the top screws are different from other screws. Use the optional keyless drill chuck assembly. When installing it, refer to "Installing or removing the bit" described on the previous page. Set the change lever so that the pointer points to the symbol. Hold the ring and turn the sleeve counterclockwise to open the chuck jaws.
1. Connector 1 008604 • 008606 Connect the connector firmly and then reinstall the handle. CAUTION: Always remove the crank cap only after aligning the change lever with the symbol . Never remove it forcibly without aligning the change lever with the symbol . Failure to do so does not allow reassembling. CAUTION: Be careful not to damage the connector or lead wires especially when installing the handle.
Makita Corporation Anjo, Aichi, Japan 884815C227 12
