User Manual
9ENGLISH
SаТtМСăКМtТШЧ
ŻТР.ń2Śă1. Lock-off lever 2. Switch trigger
CAUTION: ŰОПШrОăТЧsОrtТЧРătСОăЛКttОrвăМКr-
trТНРОăТЧtШătСОătШШХĽăКХаКвsăМСОМФătШăsООătСКtătСОă
sаТtМСătrТРРОrăКМtuКtОsăЩrШЩОrХвăКЧНărОturЧsătШă
tСОăąЇŻŻąăЩШsТtТШЧăаСОЧărОХОКsОН.
CAUTION: DШăЧШtăЩuХХătСОăsаТtМСătrТРРОră
СКrНăаТtСШutăЩrОssТЧРătСОăХШМФľШППăХОЯОr.ăTСТsăМКЧă
МКusОăsаТtМСăЛrОКФКРО.
the lock-off lever and pull the switch trigger. Release the
switch trigger to stop.
WARNING: ŻШrăвШurăsКПОtвĽătСТsătШШХăТsă
ОquТЩЩОНăаТtСăХШМФľШППăХОЯОrăаСТМСăЩrОЯОЧtsătСОă
tШШХăПrШЦăuЧТЧtОЧНОНăstКrtТЧР.ăІźVźRăusОătСОă
tШШХăТПăТtăruЧsăаСОЧăвШuăsТЦЩХвăЩuХХătСОăsаТtМСă
trТРРОrăаТtСШutăЩrОssТЧРătСОăХШМФľШППăХОЯОr.ăRОturЧă
tШШХăКăMůKITůăsОrЯТМОăМОЧtОrăПШrăЩrШЩОrărОЩКТrsă
ŰźŻЇRźăПurtСОrăusКРО.
WARNING: ІźVźRătКЩОăНШаЧăШrăНОПОКtăЩur-
ЩШsОăКЧНăПuЧМtТШЧăШПăХШМФľШППăХОЯОr.
ASSEMBLY
CAUTION: ůХаКвsăЛОăsurОătСКtătСОătШШХăТsă
sаТtМСОНăШППăКЧНătСОăЛКttОrвăМКrtrТНРОăТsărОЦШЯОНă
ЛОПШrОăМКrrвТЧРăШutăКЧвăаШrФăШЧătСОătШШХ.
RОЦШЯТЧРăШrăТЧstКХХТЧРăМТrМuХКrăsКаă
blade
ŻТР.ń3Śă1. Shaft lock 2. Hex wrench
CAUTION: ŰОăsurОătСОăМТrМuХКrăsКаăЛХКНОăТsă
ТЧstКХХОНăаТtСătООtСăЩШТЧtТЧРăuЩăКtătСОăПrШЧtăШПătСОă
tool.
CAUTION: UsОăШЧХвătСОăMКФТtКăаrОЧМСătШă
ТЧstКХХăШrărОЦШЯОătСОăМТrМuХКrăsКаăЛХКНО.
ŻТР.ńŐŚă
-
ŻТР.ńőŚă
NOTE:
-
mulated sawdust as discussed in the Maintenance
section. Such efforts do not replace the need to check
HОбăаrОЧМСăstШrКРО
ŻТР.ń6Śă1. Hex wrench
When not in use, store the hex wrench as shown in the
űШЧЧОМtТЧРăКăЯКМuuЦăМХОКЧОr
Optional accessory
ŻТР.ń7Śă1. Dust nozzle (optional accessory)
2. Screw (optional accessory)
ŻТР.ńŘ
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Install
the dust nozzle (optional accessory) on the tool using
OPERATION
CAUTION: ŰОăsurОătШăЦШЯОătСОătШШХăПШrаКrНă
ТЧăКăstrКТРСtăХТЧОăРОЧtХв. Forcing or twisting the tool
will result in overheating the motor and dangerous
NOTE:
time, for example, use the tool for a light-duty cut for
full capacity.
ŻТР.ńř
move the tool forward over the workpiece surface,
is completed.
your speed of advance uniform. If the cut fails to prop-
erly follow your intended cut line, do not attempt to turn
-
avoid positioning which exposes operator to chips and