Chain Vise Recipro Saw MODEL JR3010 INSTRUCTION MANUAL SPECIFICATIONS Length of stroke 28 m m 11-118") Strokes per minute 0 - 2,200 Vise capacity :,?,--':-:; Overall length Net weight ,without 435 m m 117-1/8") Manufacturer reserves the right t o change specifications without notice. * Note: Specifications may differ from country t o country. 2.9 k g (6.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired. 18.
ADDITIONAL SAFETY RULES 1. Wear a hard hat (safety helmet), safety glasses and/or face shield. It is also highly recommended that you wear a dust mask, ear protectors and thickly padded gloves. 2. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 3. Do not attempt to cut workpieces larger than specified in this manual (especially hollow pipe). The blade might snap and cause an injury. 4. 5. 6. 7. Hold the tool firmly.
Installing or removing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. The blade installing position varies depending upon the type of blade being used. Install the blade in the proper position as shown in the figures below. Installing position for blades No. 25 and 26. Installing position for blades No. 21, 22, 23 and 24. To install the blade, loosen the bolt with the hex wrench.
Installing or removing vise assembly To install the vise assembly, insert the shaft of the vise assembly into the hole in the housing as far as it will go. The shaft of the vise assembly will be grasped by the stopper automatically. Make sure that the vise assembly cannot be removed even though you try t o pull it out. To remove the vise assembly, raise the stopper and then pull the vise assembly out while turning the vise assembly.
Operation 1. Cutting with the vise assembly : Secure the tool to the workpiece as described in “Securing tool to workpiece” section. Bring the blade into light contact with the workpiece. First, make a pilot groove, using a slower speed until the blade has cut t o a depth of 1 - 3 mm (3/64”- 1/8’)). Then use a faster speed to continue cutting. CAUTION : Do not l i f t the tool handle too hard during operation. This may cause a bevel cut, damage to the blade or damage to the tool.
MAINTENANCE CAUTION : Always be sure that the tool i s switched off and unplugged before attempting t o perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Saw Blades Wood Cutting Blade Part ## 1723018-0A 723018-A-5 7230 18-A-2 Oty. Per Pkg. Teeth Per Inch 1 I 1 1 I 1 723018-0E 723018-E-5 723018-P-5 I Metal Cutting Blade For rapid cutting of metal and fiberglass. Made of high speed steel. 10 1 1 /! 1 6 I 1723018-OD 723018-D5 723018-D-2 I 6' 6' 6" High Carbon Steel Fleam Ground 1.049" I Cuts nail free wood -rough In work. 12" High Carbon Steel Fleam Ground 1.049") Cuts nail free wood - rough in work.
Saw Blades Bi-metal Blade Combination of high speed steel teeth welded to a shatter proof flexiblf backed blade. Ultra long l i f e blade. Part I my. I Teeth Per Pkg. Per Inch Overall Length 5 6 12" 1 1 10 10 10 E" 6* 1 I 1 5 4" I 6" 723017-E5 723017-E-2 723017-F-5 723017.
Aug.-17-'89 US CHAIN VISE RECIPRO SAW Model JR3010 Note: The switch, noise suppressor and other part configurations may differ from country t o country.
MODEL JR3010 ,& M :i' Aug - 1 7 ' 8 9 1 2 2 1 15 1 16 17 1 11 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 38 37 38 39 40 41 42 43 44 45 46 47 48 1 1 1 12 13 14 IO ~ 1 2 2 2 2 2 1 US DESCRIPTION MACHINE MACHINE ~ 1 2 3 4 5 6 7 8 9 A&, M :i' DESCRIPTION 1 1 1 3 3 3 1 I I 49 50 51 52 53 54 55 56 1 1 57 58 59 82 83 64 65 66 67 68 69 70 71 72 73 76 77 78 19 80 81 82 83 1 1 1 1 1 1 I 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 - - - 1 1 4 4 1 1 1 1 1 I I 2 1 1 1 1 1 1 1