Recipro Saw MODEL JR3030 Variable MODEL Speed JR3030T Variable Speed INSTRUCTION MANUAL [_ DOUgLE INSULATION SPECIFICATIONS Model Length of stroke Strokes per minute 28 mm (1-3/32") I * Manufacturer WARNING: SAVE reserves Specifications For your THESE the right to change may differ personal INSTRUCTIONS Overall length 0 -- 2,600 JR3030 JR3030T Note: __ from safety, FOR specifications country READ FUTURE and 438 mm (17-1/4"1 460 mm (18-118") without notic_ to country.
GENERAL SAFETY RULES (For All Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS READ ALL INSTRUCTIONS. WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2, Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. 12. Remove adjusting keys or switches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 14.
Specific Safety Rules 1. Hold tool by insulated gdpping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator. 2. Avoid cutting operation. nails. Inspect workplace 3. Do not cut oversize for any nails and remove them before workpiece. 4. Check for the proper clearance beyond the workpiece the blade will not strike the floor, workbench, etc.
SYMBOLS The followings show the symbols used for tool. V ................................. volts A ................................. amperes Hz ................................. herts kg h ................................. ................................. kilograms hours rain ................................. minutes S ................................. seconds ................................. alternating current .... ................................. direct current n, .............
FUNCTIONAL DESCRIPTION Ad]. ng =11oo When the blade loses its cutting efficiency in one place along its cutting edge, reposition the shoe to unitize a shaqo, unused portion of its cutting edge. This will help to lengthen the life of the blade. To reposition the shoe, loosen the lever and slide the shoe forward or back to the desired position. Then tighten the lever to firmly secure the shoe.
ASSEMBLY Installing or removing the saw blade CAUTION: • Always be sure that the tool is switched off and unplugged before installing or removing the blade. oAIways clean out all chips or foreign matter adhering to the blade, blade clamp and/or slider. Failure to do so may cause insufficient tightening of the blade, resulting in a serious injury. For JR3030 To install the blade, loosen the screw on the blade clamp with the hex wrench 4 provided.
For JR30301" To installthe blade,pushthe pushbutton in the directionof the arrowand insertthe blade between the bladeclamp and the slider as far as it will go. Then release the pushbutton and make sure that the bladecannotbe extractedeven thoughyou try to pull it out. CAUTION: If you releasethe pushbuttonwithout insertingthe bladedeep enough,the blademay be ejected unexpectedlyduringoperation.Thiscan be extremely dangerous.
OPERATION Press the shoe firmly against the workpiece. Do not allow the tool to bounce. Bringthe blade into light contact with the workpiece. First,make a pilotgroove, using a slower speed.Then use a faster speed to continuecutting. CAUTION: • Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so wil{ cause premature blade wear. • Always wear gloves to protect your hands from hot flying chips when cutting metal.
MAINTENANCE CAUTION: Always be sure that the tool is switchedoff and unpluggedbefore attemptingto perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Urnit mark Use a screwdriver to remove the brush holder caps.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessoriesor attachmentsmight present a riskof injuryto persons. These accessories or attachments should be used only in the proper and intended manner, NOTE: The accessories listed in this manual are available at the extra cost from your Makita distributor or Makita Factory Service Center.
ACCESSORIES Saw Ehdm Combination of high spud stui tleth welded to a shatter. flexible blade. blade, Ultra-long Oty PwPkg Part# Bi-metM Blades proof, continuedOwlrllll Llmgth : Tooth SIHclflcltiOml AppliCation Cuts nail embedded 723017-E-5 723017-E-2 66,* Bi-metsl Milled (0.050") 723017-F-5 12" B_,metal milled (0,050") Cuts nail embedded wood -- roughing in work. Bi-metal Milled (0.031 ") CUts nail embedded wood _ nonferrous metals. backed wood work.
Feb--18 ,99 US RECIPRO SAW Model JR3030 65 68_ 70 Note: The switch and other part configurations may differ from country to country.
Feb.-18-'99 MODEL JR3030 ITEM NO. NO_ USED ITEM N_ DESCRIPTION 1 2 3 2 I I I ! 2 I 2 I made C4amp Hex. Socket Screw Head BO_ M5x15 MSxl0 Twppin9 Scxew Felt Retorter 5 6 ? 8 9 10 11 12 13 14 lS 16 17 18 19 2O 21 22 23 14 25 28 27 28 29 Bind CT 5xl2 Fell Ring 14 Fta_ Wuhe_ 14 X R_ng 14 Flal Wesher Gear 16 Housing Cover Pan Head Screw _0 MSx30 Shoe F_Btt Stop Rirtg EFlex. 52 _3 _4 S6 _6 57 58 59 _0 3 Lock Nut MS-8 Pm4 He_.
MAKITA LIMrI ) ONE YEAR WARRANTY Warranty Policy Ev©ry Makilatoolb thoroughly "ms_scted and t_ted beforele_ thefactow. Iti_w_mt ed to be fxceof defectsfTom workmlp L_dmaterials forthepe, r_odofONE YEAR fromthedateof o_Inal _Me. _ould an},trouble, d_elop dad_ th=_m_-y_ pe_od,_tusn.t_eO_MPLETE cool fn_t pn_p.id, to one of Mskita s FL-_P/or Autho"_. Se_e _tcrL Ifmsp_tion shpws the trouble b csmed by dcfcc_e wodmumship or matcr_l, Makiu win _*_it (or at our optton, repine) without cktrl_.