Straight Shear MODEL JS1670 INSTRUCTION MANUAL DOUBLE INSULATION SPEC1FICAT IONS Mild steel 1.0 mm (3164") Hard steel 1 0.7 mm (1132") Stainless I 0.7 mm (1132") Aluminum I 1.5 mm 11/16") I Min cutting radius 3 0 mm (l-l/8'') I 4'500 * Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. I 306 mm (12") I 1.3 kg (2.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor. ADDITIONAL SAFETY RULES 1. Secure the workpiece firmly. 2.
Lubrication Before operation, lubricate the contact point of the center blade and the pin. To keep good cutting performance, also use a cutting lubricant from time to time during operation. Switch action To start the tool, move the slide switch forward, and the slide switch will lock in the "ON" position. To stop, lightly depress the rear of the slide switch, and it will return to the "OFF" position.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting t o perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. Limit mark Use a screwdriver t o remove the brush holder caps.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. 0 Hex wrench 3 Part No. 783201-2 0 Wrench holder Part No.
Apr -24-537 EN STRAIGHT SHEAR Model JS1670 Note: The switch, noise suppressor and other part configuratlons may differ from country to country.
July-17-'89 MODEL JS1670 $2D OM' , : ' DESCRIPTION 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 4 1 1 1 1 1 1 1 1 1 1 1 I 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 $2D DESCRIPTION MACHlNE MACHINE ~ 1 2 3 4 5 6 7 8 9 "0" US Pan Head Screw M4x35 (With Washer1 Block Hex Lock N u t M 4 - 7 Set Screw M5x12 Pan 7 Stop Ring E - 6 Rubber Pin 4 Ball Bearing 627LLB Flat Washer 7 Rod Ball Bearing 6000CLB Crank Shaft Bush Ball Bearing 6000L8 Helical Gear 44 Retaining Ring 5 - 1 0 Ball Bearing 60
MAKlTA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool IS thoroughly inspected and tested before leaving the factory. It IS warranted t o be free of defects from workmanship and materials for the penod of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year penod, return the COMPLETE tool, freight prepaid, lo one of Makita’s Factory or Authorized Service Centers.