ENGLISH INSTRUCTION MANUAL Power Planer KP0810 KP0810C 007638 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH SPECIFICATIONS Model KP0810 Planing width KP0810C 82 mm Planing depth 4 mm Shiplapping depth 25 mm No load speed (min-1) 16,000 Overall length 12,000 290 mm Net weight 3.2 kg Safety class 3.3 kg /II • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. • Note: Specifications may differ from country to country. value is not more than 2.5 m/s2. These values have been obtained according to EN60745.
GEA001-3 reduce personal injuries. Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents. 12. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 13. Do not overreach. Keep proper footing and balance at all times.
of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. SERVICE 23. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 24. Follow instruction for lubricating and changing accessories. 25. Keep handles dry, clean and free from oil and grease. 16. 17.
For tool with lock button To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button from either side. To stop the tool from the locked position, pull the switch trigger fully, then release it. For tool with lock-off button To prevent the switch trigger from being accidentally pulled, a lock-off button is provided.
plate into the drum groove, then fit the drum cover on it. Tighten all the installation bolts evenly and alternately with the socket wrench. For tool with mini planer blades 1. Remove the existing blade, if the tool has been in use, carefully clean the drum surfaces and the drum cover. To remove the blades on the drum, unscrew the three installation bolts with the socket wrench. The drum cover comes off together with the blades. 4. 5. 6. 1. Socket wrench 1 pan head screws.
(A) Front base (Movable shoe) (B) Rear base (Stationary shoe) Correct setting (A) (B) Although this side view cannot show it, the edges of the blades run perfectly parallel to the rear base surface. Cause: One or both blades fails to have edge parallel to rear base line. Nicks in surface Gouging at start (A) (B) Cause: One or both blade edges fails to protrude enough in relation to rear base line. (B) Cause: One or both blade edges protrudes too far in relation to rear base line.
OPERATION 1. Fastener Hold the tool firmly with one hand on the knob and the other hand on the switch handle when performing the tool. Planing operation 1 1 2 1. Start 2. End 007802 NOTE: • If you connect a Makita vacuum cleaner to this tool, more efficient and cleaner operations can be performed. 007646 Connecting a vacuum cleaner 1 First, rest the tool front base flat upon the workpiece surface without the blades making any contact. Switch on and wait until the blades attain full speed.
1. Blade edge 2. Cutting line 3. Depth guide 3 2 1 007647 007714 Install the edge fence on the tool and secure it with the washer and thumb screw (A). Loosen the thumb screw (B) and adjust the edge fence until it comes in contact with the side of the workpiece. Then tighten the thumb screw (B) securely. Chamfering 1. Screw (A) 2. Screw (B) 3.
and make many passes of planing as shown in the figure. b a 1. Edge of chamfering rule 1 002590 Replacing carbon brushes 007828 1. Limit mark MAINTENANCE • CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 1 Sharpening the planer blades 001145 For standard blades only Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge.
always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Makita Corporation Anjo, Aichi, Japan 884693B225 12