INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Slide Compound Miter Saw Scie à Onglet Radiale Sierra de Inglete Telescópica LS0815F LS0815FL 014288 DOUBLE INSULATION DOUBLE ISOLATION DOBLE AISLAMIENTO IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model LS0815F /LS0815FL Blade diameter 216 mm (8-1/2") Hole diameter 15.88 mm (5/8") Max. Miter angle Left 50° Right 60° Max. Bevel angle Left 48° Right 5° Max.
12. 13. 14. 15. 16. 17. 18. 19. 20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop. 22. REPLACEMENT PARTS. When servicing, use only identical replacement parts. 23. POLARIZED PLUGS. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other).
USB036-3 16. ADDITIONAL SAFETY RULES DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to slide compound saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Wear eye protection. 2. Keep hands out of path of saw blade. Avoid contact with any coasting blade. It can still cause severe injury. 3. Do not operate saw without guards in place. Check blade guard for proper closing before each use.
30. 31. 32. Do not abuse cord. Never yank cord to disconnect it from the receptacle. Keep cord away from heat, oil, water and sharp objects. NEVER stack workpieces on the table top to speed cutting operations. Cut only one piece at a time. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. INSTALLATION Bench mounting 1. Stopper pin 1 SAVE THESE INSTRUCTIONS.
secure bolt. Do not remove spring holding blade guard. If guard becomes damaged through age or UV light exposure, contact a Makita service center for a new guard. DO NOT DEFEAT OR REMOVE GUARD. FUNCTIONAL DESCRIPTION • WARNING: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Failure to switch off and unplug the tool may result in serious personal injury from accidental start-up. 1. Blade guard 1 Blade guard 1.
NOTICE: • After setting the bevel angle ensure that the kerf boards are adjusted properly. Correct adjustment of the kerf boards will help provide proper support of the workpiece minimizing workpiece tear out. Stopper arm 1 1. Stopper arm 2. Adjusting screw 2 Maintaining maximum cutting capacity This tool is factory adjusted to provide the maximum cutting capacity for a 216 mm (8-1/2") saw blade. Unplug the tool before any adjustment is attempted.
To adjust the bevel angle, loosen the lever at the rear of the tool counterclockwise. Unlock the arm by pushing the handle somewhat strongly in the direction that you intend to tilt the saw blade. Slide lock adjustment 1. Locking screw NOTE: • Lever can be adjusted to a different lever angle by removing the screw holding the lever and securing the lever at a desired angle. 1 1 1. Lever 2. Arm 3. Pointer 4. Bevel scale 011352 To lock the slide pole, turn the locking screw clockwise.
result in unintentional operation and serious personal injury. Return tool to a Makita service center for proper repairs BEFORE further usage. NEVER defeat the lock-off button by taping down or some other means. A switch with a defeated lock-off button may result in unintentional operation and serious personal injury. • Laser line can be shifted to either the left or right side of the saw blade by loosening the screw holding the laser unit box and shifting it in the desired direction.
Use only the Makita socket wrench provided to install or remove the blade. Failure to use the wrench may result in overtightening or insufficient tightening of the hex bolt and serious personal injury. • 1. Switch for light 1. Stopper pin 1 1 014274 To turn on the light, press the upper position (ON) of the switch. To turn off the light, press the lower position (OFF) of the switch. • CAUTION: Do not look in the light or see the source of light directly.
flanges. Use of the incorrect arbor hole ring may result in the improper mounting of the blade causing blade movement and severe vibration resulting in possible loss of control during operation and in serious personal injury. 2 1 3 Dust bag 1 2 1. Blade case 2. Arrow 3. Arrow 4. Saw blade 1. Dust nozzle 2. Dust bag 3. Fastener 3 014283 The use of the dust bag makes cutting operations cleaner and dust collection easier. To attach the dust bag, fit it onto the dust nozzle.
1 Vertical vise 1. Support 2. Turn base 2 1 5 Guide fence (SLIDING FENCES) adjustment 1 014289 The vertical vise can be installed on either the left or right side of the guide fence. Insert the vise rod into the hole in the guide fence and tighten the screw on the back of the guide fence to secure the vise rod. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw.
Push the carriage toward the guide fence fully and tighten the locking screw clockwise to secure the carriage. Secure the workpiece correctly with the proper type of vise. Switch on the tool without the blade making any contact and wait until the blade attains full speed before lowering. Then gently lower the handle to the fully lowered position to cut the workpiece.
• • • • WARNING: Whenever performing a slide cut, first pull the carriage full towards you and press the handle all the way down, then push the carriage toward the guide fence. Never start the cut with the carriage not pulled fully toward you. If you perform the slide cut without the carriage pulled fully toward you unexpected kickback may occur and serious personal injury may result. Never attempt to perform a slide cut by pulling the carriage towards you.
In the case of left bevel cut 1. 52/38 ﾟ type crown molding 2. 45 ﾟ type crown molding 3. 45 ﾟ type cove molding 1 2 Table (A) Bevel angle Molding position in 52/38° type 45° type Fig. A For inside corner 3 For outside corner (1) (2) (3) (4) Miter angle 52/38° type 45° type Right 31.6° Right 35.3° Left 33.9° Left 30° Left 31.6° Left 35.3° Right 31.6° Right 35.3° 006361 001555 There are crown and cove molding joints which are made to fit "Inside" 90° corners ((1) and (2) in Fig.
Compound Miter Saw Miter and Bevel Angle Settings Wall Ceiling 000031 Wall to Crown Molding Angle: 52/38 degrees Wall Angle (deg.) 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Bevel Angle (deg.) 43.0 42.8 42.5 42.2 41.9 41.7 41.4 41.1 40.8 40.5 40.2 39.9 39.6 39.3 39.0 38.7 38.4 38.1 37.8 37.4 37.1 36.8 36.5 36.2 35.8 35.5 35.2 34.9 34.5 34.2 33.9 33.5 33.2 32.8 32.5 32.2 31.8 31.5 31.1 30.8 30.4 Miter Angle (deg.) 46.8 46.
Compound Miter Saw Miter and Bevel Angle Settings Wall Ceiling 000032 Wall to Crown Molding Angle: 45 degrees Wall Angle (deg.) 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Bevel Angle (deg.) 37.8 37.5 37.3 37.1 36.8 36.6 36.4 36.1 35.9 35.6 35.4 35.1 34.9 34.6 34.4 34.1 33.9 33.6 33.3 33.1 32.8 32.5 32.3 32.0 31.7 31.4 31.1 30.9 30.6 30.3 30.0 29.7 29.4 29.1 28.8 28.5 28.2 27.9 27.6 27.3 27.0 Miter Angle (deg.) 50.8 50.
7. NOTICE: • When the wood facing is attached, do not turn the turn base with the handle lowered. The blade and/or the wood facing will be damaged. Cutting aluminum extrusion 2 3 4 1 1. Guide fence 2. Vise 3. Spacer block 4. Aluminum extrusion 5. Spacer block 9. Groove cutting 1 1. Cut grooves with blade 5 010404 When securing aluminum extrusions, use spacer blocks or pieces of scrap as shown in the figure to prevent deformation of the aluminum.
Make sure that the tool is unplugged. Secure the blade at 0° bevel angle and the turn base at the full right miter angle position. Secure the slide poles so that the lower slide pole is locked in the position of the carriage fully pulled to operator and the upper poles are locked in the position of the carriage fully pushed forward to the guide fence (refer to the section titled "Slide lock adjustment ".) Lower the handle fully and lock it in the lowered position by pushing in the stopper pin.
2. Bevel angle (1) 0° bevel angle 1. Screw 2. Pointer 3. Bevel scale 1. Lever 2. Arm 1 2 3 1 2 014286 Make sure that the pointer on the arm point to 0° on the bevel scale on the arm holder. If they do not point to 0°, loosen the screw which secure the pointer and adjust it so that it will point to 0°. 45° bevel angle 014299 Push the carriage toward the guide fence and tighten the locking screw to secure the carriage.
Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. • • • 1. Screwdriver 2. Brush holder cap • • Vertical vise Socket wrench with hex wrench on its other end Holder Dust bag Triangular rule NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
