Specifications

ManualsBrandsMakita ManualsSawLS1030N

SPECIFICATIONS

Model LS1030N

Blade diameter .....................................................................................................................255 mm — 260 mm

Hole (arbor) diameter

For all countries other than European countries ............................................................. 25.4 mm and 25 mm

For European countries ......................................................................................................................... 30 mm

Max. cutting capacities (H x W) with blade 260 mm in diameter

No load speed (min

–1

) ............................................................................................................................... 4,600

Dimensions (L x W x H) ........................................................................................530 mm x 476 mm x 532 mm

Net weight ...................................................................................................................................................11 kg

• Due to our continuing program of research and development, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They are double-insulated in accordance with European

Standard and can, therefore, also be used from sockets without earth wire.

Miter angle

Bevel angle

0° 45° (left and right)

0°

90.5 mm x 95 mm

69 mm x 135 mm

90.5 mm x 67 mm

69 mm x 95 mm

Miter Saw

LS1030N

Summary of content (12 pages)

PAGE 1
Miter Saw LS1030N SPECIFICATIONS Model LS1030N Blade diameter .....................................................................................................................255 mm — 260 mm Hole (arbor) diameter For all countries other than European countries ............................................................. 25.4 mm and 25 mm For European countries ......................................................................................................................... 30 mm Max.
PAGE 2
1 1 2 2 5 3 4 3 3 4 7 6 8 10 10 8 12 9 6 11 5 6 5 13 14 7 2 8
PAGE 3
16 15 17 9 10 18 20 19 11 12 22 23 3 21 13 14 24 27 25 26 135 mm 15 16 3
PAGE 4
32 31 28 29 22 33 22 30 17 18 35 5 34 19 20 29 37 38 36 37 21 29 22 39 41 30 42 43 40 23 4 42 24
PAGE 5
45 44 90 mm 40 mm 46 137 mm 70 mm 70 mm 46 137 mm 25 47 48 27 29 30 36 26 27 49 12 28 29 50 51 30 5
PAGE 6
Symbols The following show the symbols used for the tool. Be sure that you understand their meaning before use. ❏ Read instruction manual. ❏ DOUBLE INSULATION ❏ To avoid injury from flying debris, keep holding the saw head down, after making cuts, until the blade has come to a complete stop. ❏ For your safety, remove the chips, small pieces, etc. from the table top before operation.
PAGE 7
ENGLISH Explanation of general view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Bolt Center cover Socket wrench Shaft lock Loosen Arrow Blade case Saw blade Spindle Flange Ring Hex bolt Tighten Safety cover Dust spout Dust bag Fastener 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Lock-off button Switch lever Lever Kerf board Turn base Adjusting bolt Pointer Miter scale Latch spring Grip Vise rod Screw Guide fence Clamp screw Vise arm Support Knob SAFETY INSTRUCTIONS Warning! When using electric tool
PAGE 8
20. Check damaged parts Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.
PAGE 9
CAUTION: • For all countries other than European countries (Fig. 6) The silver ring 25.4 mm in outer diameter is factoryinstalled onto the spindle. The black ring 25 mm in outer diameter is included as standard equipment. Before mounting the blade onto the spindle, always be sure that the correct ring for the arbor hole of the blade you intend to use is installed onto the spindle. • For European countries (Fig. 6) The ring 30 mm in outer diameter is factory-installed onto the spindle.
PAGE 10
If some part contacts the vise, re-position the vise arm. Press the workpiece flat against the guide fence and the turn base. Position the workpiece at the desired cutting position and secure it firmly by tightening the clamp screw of the vise. CAUTION: When cutting long workpieces, use supports that are as high as the top surface level of the turn base. (Fig. 18) 2. 3. Horizontal vise (optional accessory) (Fig. 19 & 20) The horizontal vise can be installed on either the left or right side of the base.
PAGE 11
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Alignment for squareness (Fig. 27 & 28) This tool is carefully adjusted and aligned at the factory, but rough handling may have affected the alignment. If your tool is not aligned properly, perform the following: Loosen the grip and set the turn base at zero degrees by turning the turn base. Tighten the grip securely and loosen the hex bolts on the guide fence.
PAGE 12
Makita Corporation Anjo, Aichi, Japan Made in China 884146A8