INSTRUCTION MANUAL Cordless Vacuum Cleaner LXCV01 LXCV02 011111 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS LXCV01 Model LXCV02 Volume Capacity 3.0 L Max. Air volume 3.3 m3/min. 3.4 m3/min. HIGH Approx. 10 min. (with BL1430) Approx. 13 min. (with BL1830) LOW Approx. 20 min. (with BL1430) Continuous use Overall length Approx. 26 min. (with BL1830) 403 mm Net weight 2.1 kg 2.2 kg Rated voltage D.C. 14.4 V D.C.
ENC007-6 − 3. 4. 5. 6. 7.
• FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the cleaner is switched off and the battery cartridge is removed before adjusting or checking function on the cleaner. NOTE: • This temperature-sensitive protection is applied only when the cleaner is used with a battery cartridge with a star mark. Installing or removing battery cartridge 2 1 When the remaining battery capacity gets low: If any operation of the "HIGH/LOW" button and the "OFF" button, the motor will remain stopped.
ASSEMBLY • • 1. Protrusion 1 CAUTION: Always be sure that the cleaner is switched off and the battery cartridge is removed before carrying out any work on the cleaner. Any work with the battery cartridge being installed on the cleaner may cause a personal injury or damage to the objects around the cleaner. 011115 (2) Installing dust bag Tighten the ring inside the dust bag firmly so that the pins and the ring are positioned as shown in the figure. 2 1 1. Pins 2.
Adjusting the shoulder strap 3 1 1. Pull out 2. For shortening 3. For extending 1 1. Front cuff 2. Hose 3. Remove 4. Install 2 3 2 4 011120 To adjust the length of the shoulder strap, pull it out to your desired length and pull the strap in the direction of arrow as shown in the figure. To remove the front cuff, hold the hose and turn it counterclockwise. To mount the front cuff, turn it clockwise and then screw it in until it stops.
Using as a blower 1 2 1. Outlet (air vent) 2. Nozzle 3. Pin 1 2 3 3 011124 Install the nozzle onto the outlet (air vent) without fail. To install the nozzle, fit the pin protruding from the inside of nozzle to one of the cleaner notches and then turn the nozzle clockwise securely. To remove the nozzle, turn counterclockwise and pull it out. Direct the top point of the cleaner and then switch on. 4 5 1. Decorative paper 2. Saw blade 3. Base 4. Cutting depth 5.
1. Filter area 1 1 2 1. Dust bag joint 2. Square section 011127 Check and clean up the filter area in the suction inlet regularly. Remove foreign objects which will obstruct suction. Cleaning From time to time wipe off the outside (cleaner body) of the cleaner using a cloth dampened in soapy water. 011125 CAUTION: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
