ENGLISH (Original instructions) INSTRUCTION MANUAL Router RP0900 009743 DOUBLE INSULATION IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model RP0900 Collet chuck capacity 6mm, 1/4", 8 mm and/or 3/8" Plunge capacity 0 - 35 mm No load speed (min-1) 27,000 Overall height 217 mm Net weight 2.7 kg Safety class /II • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country.
electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20.
FUNCTIONAL DESCRIPTION • • CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. • Adjusting the depth of cut 1. Stopper pole 2. Screw 1 CAUTION: Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 15 mm at a pass when cutting grooves with an 8 mm diameter bit.
Adjusting the lock lever CAUTION: Install the bit securely. Always use only the wrenches provided with the tool. A loose or overtightened bit can be dangerous. • Do not tighten the collet nut without inserting a bit. It can lead to breakage of the collet cone. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. A 6 mm or 1/4" collet cone is also provided as standard equipment besides the 8 mm or 3/8" collet cone that is factory installed on the tool.
2 3 1 Templet guide (Accessory) 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Straight guide 4 001985 Straight guide 009752 The templet guide provides a sleeve through which the bit passes, allowing use of the tool with templet patterns. To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. 1 2 1. Screw 2. Base 3.
Dust nozzle set (Accessory) 1 2 1. Dust nozzle 2. Thumb screw 009754 Use the dust nozzle for dust extraction. Install the dust nozzle on the tool base using the thumb screw so that protrusion on the dust nozzle fit to the notch in the tool base. Then connect a vacuum cleaner to the dust nozzle. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Drill point flush trimming bit Router bits Straight bit 005120 mm 005116 mm D 6 A L1 L2 20 50 15 8 8 60 25 6 1/4" 8 50 18 6 1/4" 6 50 18 1/4" D A L1 L2 L3 8 8 60 20 35 6 6 60 18 28 009806 Drill point double flush trimming bit 009802 "U"Grooving bit 005121 mm R D A L1 L2 L3 L4 8 8 80 55 20 25 6 6 70 40 12 14 009807 Corner rounding bit 005117 mm D A L1 L2 R 6 6 50 18 3 009803 "V"Grooving bit 005125 mm D A1 A2 L1 L2 L3 R 6
Ball bearing corner rounding bit Chamfering bit 005126 005131 mm D A L1 L2 L3 6 23 46 11 6 6 20 50 13 5 6 20 49 14 2 60 mm D A1 A2 L1 30 6 15 8 45 6 21 8 1/4" L2 L3 R 37 7 3.5 3 40 10 3.
Ball bearing cove beading bit 005134 mm R D A1 A2 A3 A4 L1 L2 L3 6 20 18 12 8 40 10 5.5 3 6 26 22 12 8 42 12 5 5 009815 Ball bearing roman ogee bit 005135 D A1 A2 L1 L2 L3 R1 mm R2 6 6 20 26 8 8 40 42 10 12 4.5 4.5 2.5 3 4.5 6 009816 NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
Makita Corporation Anjo, Aichi, Japan 884875D229 12 www.makita.
