Instruction manual

ENGLISH
Explanation of general view
1 Push button
2 Battery cartridge
3 Charging light
4 Battery charger
5 Cutter head
6 Hex socket head bolt
7 Flat washer
8 Cutter head
9 Vents
10 Switch trigger
11 Steel rod
12 Cutters
13 Adjusting hex bolt
14 Protector
15 Vent hole
16 Hex wrench
17 Return valve
18 Hex bolt
SPECIFICATIONS
Model SC190D
Cutting capacity
(Diameter) ..........................3–19mm(1/8″ — 3/4″)
Cutting speed ........................................... 6 seconds
Overall length ............................... 430 mm (16-3/8″)
Net weight ........................................ 10.5 kg (23 lbs)
Rated voltage ............................................ D.C. 18 V
•
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
•
Note: Specifications may differ from country to
country.
For Your Own Safety
Read Instruction Manual
Before Operating Tool
Save it for future reference
GENERAL SAFETY PRECAUTIONS
(For all tools)
1. KNOW YOUR POWER TOOL. Read the own-
er’s manual carefully. Learn the tool’s applica-
tions and limitations, as well as the specific
potential hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working
order.
3. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed
from tool before turning it on.
4. KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
5. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet loca-
tions, or expose them to rain. Keep work area
well lighted. Don’t use tool in presence of
flammable liquids or gases.
6. KEEP CHILDREN AWAY. All visitors should be
kept safe distance from work area.
7. MAKE WORKSHOP KID PROOF with pad-
locks, master switches, or by removing starter
keys.
8. DON’T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don’t force tool or attach-
ment to do a job for which it was not designed.
10. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long
hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resis-
tant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and it frees both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and
balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating and
changing accessories.
15. DISCONNECT BATTERY FROM TOOL before
servicing; when changing accessories such
as blades, bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off position
before inserting battery.
17. USE RECOMMENDED ACCESSORIES. Con-
sult the owner’s manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool
is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function - check for align-
ment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade
or cutter against the direction of rotation of the
blade or cutter only.
21. NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Don’t leave tool
until it comes to a complete stop.
4
SC190DW (E) (’100. 11. 17)