Operation Manual

7 ENGLISH
Battery protection system
Thetoolisequippedwithabatteryprotectionsystem.
Thissystemautomaticallycutsoffpowertothemotorto
extendbatterylife.
Thetoolwillautomaticallystopduringoperationifthe
tooland/orbatteryareplacedunderoneofthefollowing
conditions:
Overloaded:
Thetoolisoperatedinamannerthatcausesittodraw
anabnormallyhighcurrent.
In this situation, turn the tool off and stop the application
thatcausedthetooltobecomeoverloaded.Thenturn
the tool on to restart.
Ifthetooldoesnotstart,thebatteryisoverheated.In
thissituation,letthebatterycoolbeforeturningthetool
on again.
Low battery voltage:
Theremainingbatterycapacityistoolowandthetool
will not operate. If you turn the tool on, the motor runs
againbutstopssoon.Inthissituation,removeand
rechargethebattery.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
►Fig.2: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for few seconds.
Indicator lamps Remaining
capacity
Lighted Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
from the actual capacity.
Switch action
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
tool is switched off.
►Fig.3: 1.Slideswitch
Tostartthetool,slidetheslideswitchtowardthe“I
(ON)” position.
Tostopthetool,slidetheslideswitchtowardthe“O
(OFF)” position.
Adjusting the orbital stroke rate
►Fig.4: 1. Dial
Theorbitalstrokerateisadjustable.Tochangethe
orbitalstrokerate,turnthedialbetween1and5.The
higherthenumberis,thehighertheorbitalstroke
rateis.Presetthedialtothenumbersuitableforyour
workpiece.
NOTE:Thedialcannotbeturneddirectlyfrom1to5
or from 5 to 1. Forcing the dial may damage the tool.
Whenchangingthedialdirection,alwaysturnthedial
movingitthrougheachintermediatenumber.
Lighting up the front lamp
CAUTION: Do not look in the light or see the
source of light directly.
►Fig.5: 1. Front lamp
Slidetheslideswitchtowardthe"I(ON)"positionto
lightupthefrontlamp.Thelampkeepsonlightingwhile
theswitchisthe"I(ON)"position.
Thelightautomaticallygoesoutafterpressingtherear
of the slide switch, and then sliding the slide switch
towardthe"O(OFF)"position.
Overload protection
Whenthetoolisoverloadedandtemperatureofthetoolorthe
batterycartridgereachesacertainlevel,thefrontlampblinks
and the tool automatically stops. Remove a cause of overload,
andcooldownthetoolandthebatterycartridgetorestart.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing application
tool
Optional accessory
WARNING: Do not install application tool
upside down. Installing application tool upside down
maydamagethetoolandcauseseriouspersonalinjury.
NOTE: Install application tool in the correct direc-
tion according to your work.Applicationtoolcanbe
installed at an angle of every 30 degree.
ToInstallanapplicationtool(optionalaccessory),put
theapplicationtoolonthetoolangesothattheprotru-
sionsofthetoolangetintheholesintheapplication
tool.Thensecuretheapplicationtoolbytighteningthe
boltrmlywiththehexwrench.
►Fig.6: 1.Protrusionsofthetoolange2. Holes in
the application tool 3.Applicationtoolinstal-
lationbolt
►Fig.7: 1.Applicationtoolinstallationbolt2. Hex
wrench 3.Tighten