ENGLISH: Original instructions INSTRUCTION MANUAL Cordless Impact Wrench TW140D Read before use.
SPECIFICATIONS Model: TW140D Fastening capacities Standard bolt M8 - M16 High tensile bolt M6 - M12 Square drive 9.5 mm No load speed 0 - 2,600 min-1 Impacts per minute 0 - 3,200 min-1 Overall length 161 mm Rated voltage D.C. 10.8 V - 12 V max Net weight • • • 1.0 - 1.2 kg Due to our continuing program of research and development, the specifications herein are subject to change without notice. Specifications may differ from country to country.
SAFETY WARNINGS General power tool safety warnings 2. WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 3. Save all warnings and instructions for future reference. 4. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety 1.
2. 3. 4. 5. 6. 7. 8. 9. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
. 6. 7. 8. 9. 10. 11. 12. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F).
Indicating the remaining battery capacity Switch action Only for battery cartridges with the indicator 1 1 ► 1. Switch trigger 2 CAUTION: Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. ► 1. Indicator lamps 2. Check button Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds.
Reversing switch action Installing or removing impact socket 1 2 B A 1 ► 1. Reversing switch lever ► 1. Impact socket 2. Square drive To install the impact socket, push it onto the square drive of the tool until it locks into place. To remove the impact socket, simply pull it off. CAUTION: Always check the direction of rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop.
Proper fastening torque for high tensile bolt OPERATION N•m (kgf•cm) CAUTION: Always insert the battery cartridge 140 (1430) all the way until it locks in place. If you can see the red indicator on the upper side of the button, it is not locked completely. Insert it fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan www.makita.
