INSTRUCTION MANUAL Cordless Angle Grinder XAG03 XAG04 015078 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model XAG03 XAG04 Wheel diameter 115 mm (4-1/2") 125 mm (5") Max. wheel thickness 6 mm (1/4") Spindle thread Rated speed (n) / No load speed (n0) Overall length Net weight 6 mm (1/4") 5/8" 8,500 /min With battery cartridge BL1815N, BL1820 348 mm (13-3/4") With battery cartridge BL1830, BL1840, BL1850 362 mm (14-1/4") With battery cartridge BL1815N, BL1820 2.3 kg (5.0 lbs) With battery cartridge BL1830, BL1840, BL1850 2.5 kg (5.5 lbs) 2.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
5. 6. 7. 8. 9. 10. 11. 12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 13. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 14. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 15.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. ENC007-8 Do not leave the tool running. Operate the tool only when hand-held. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. Use only flanges specified for this tool.
FUNCTIONAL DESCRIPTION • 1. Slide switch 1 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 015082 1. Button 2. Red indicator 3. Battery cartridge 1 To start the tool, slide the slide switch toward the "I (ON)" position by pushing the rear of the slide switch. For continuous operation, press the front of the slide switch to lock it.
Releasing protection lock When the protection system works repeatedly, the tool is locked and the battery indicator shows the following state. Automatic speed change function 1. Mode indicator 1 Battery indicator On Off Blinking Protection lock works 015200 In this situation, the tool does not start even if turning the tool off and on. To release the protection lock, remove the battery, set it to the battery charger and wait until the charging finishes.
For tool with locking screw type wheel guard Installing or removing wheel guard (For depressed center wheel, multi disc / abrasive cut-off wheel, diamond wheel) 1. Wheel guard 2. Bearing box 3. Screw WARNING: When using a depressed center grinding wheel/Multi-disc, wire wheel brush, cut-off wheel or diamond wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
Grinding and sanding operation Installing or removing abrasive disc (optional accessory) 1 2 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad 3 A B 015097 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.
Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel/diamond wheel 1 2 3 4 010855 Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Mount the inner flange and abrasive cut-off / diamond wheel onto the spindle. Tighten the lock nut securely with supplied wrench.
Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc and wire wheel brush.
1 6 2 3 7 4 8 2 11 10 9 3 12 5 5 115 mm (4-1/2") model 1 2 3 125 mm (5") model Grip 36 Wheel Guard (for grinding wheel) Inner flange 45 Inner flange 45 4 Depressed center wheel/Multi-disc 5 Lock nut 5/8-45 Lock nut 5/8-45 6 Rubber pad 100 Rubber pad 115 7 8 Abrasive disc Sanding lock nut 5/8-48 9 Sanding lock nut 5/8-48 Wire wheel brush 10 Wire cup brush 11 Wheel Guard (for cut-off wheel) 12 - Abrasive cut-off wheel/Diamond wheel Lock nut wrench 28 Lock nut wrench 28 01530
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
