INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Blower SOUFFLEUR SANS FIL Sopladora Inalámbrica XBU02 015474 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XBU02 Capacities Overall length Air volume (max.) 13.4 m3/min (473 cu.ft./min) Air speed 54 m/s (120 MPH) (without long nozzle) 585 mm (23") (with long nozzle) 830, 880, 930 mm (32-3/4", 34-3/4", 36-5/8") Rated voltage D.C. 36 V Standard battery cartridge(s) Warning: Use only the battery(ies) described. Net weight BL1815N / BL1820 BL1830 / BL1840 / BL1850 3.5 kg (7.7 lbs) 4.1 kg (9.
13. Do not handle charger, including charger plug, and charger terminals with wet hands. 14. Do not charge the battery outdoors. 4. Never point the nozzle at anyone in the vicinity when using the blower. 5. Never block suction inlet and/or blower outlet. • Do not block suction inlet or blower outlet to clean up in dusty areas.
may result in loss of your eyesight. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ゚ C (122 ゚ F). 7.
Press the check button to make the battery indicators show the remaining battery capacities. The battery indicators correspond to each battery. Remaining battery capacity indication NOTE: • The tool does not work with only one battery cartridge. Tool / battery protection system The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life.
For continuous operation, pull the switch trigger, push in the lock button and then release the switch trigger. To stop the tool from the locked position, pull the switch trigger fully, then release it. To install the long nozzle: 1. Align the small projection of the housing with the groove of the long nozzle. 2. Slide in the long nozzle, and turn it clockwise until the triangle markings on the long nozzle and the housing meet each other. Speed change 1.
OPTIONAL ACCESSORIES CAUTION: Do not place the blower on the ground while it is switched on. Sand or dust may enter from suction inlet, and they may result in personal injury. Hold the blower firmly with a hand and perform the blowing operation by moving it around slowly. When blowing around a building, a big stone or a vehicle, direct the nozzle away from them. When performing an operation in corner, start from the corner and then move to wide area.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Capacités Longueur totale XBU02 Volume d’air (max.) 13,4 m3/min (473 pi cu./min) Vitesse de l'air 54 m/s (120 mi/h) (sans l’embout allongé) 585 mm (23") (avec l’embout allongé) 830, 880, 930 mm (32-3/4", 34-3/4", 36-5/8") Tension nominale C.C. 36 V Batterie(s) standard Avertissement : Utilisez seulement la/les batterie(s) décrite(s).
USB101-4 CONSIGNES DE SÉCURITÉ POUR LE SOUFFLEUR 1. 2. 3. 4. 5. 6. 7. Portez toujours des lunettes de protection, un casque et un masque antipoussières lorsque vous utilisez le souffleur. Les lunettes ordinaires et les lunettes de soleil ne constituent PAS des lunettes de sécurité. Portez toujours des chaussures robustes et antidérapantes lorsque vous utilisez la machine, ainsi que des pantalons longs.
objets métalliques, par exemple des clous, des pièces de monnaie, etc. (3) Évitez d'exposer la batterie à l'eau ou à la pluie. Un court-circuit de la batterie pourrait provoquer un fort courant, une surchauffe, parfois des brûlures et même une panne. 6. Ne rangez pas l'outil ou la batterie dans des endroits où la température risque d'atteindre ou de dépasser 50 ゚ C (122 ゚ F). 7. Ne jetez pas la batterie au feu même si elle est sérieusement endommagée ou complètement épuisée.
DESCRIPTION DU FONCTIONNEMENT • NOTE: • L’outil ne fonctionne pas lorsqu’une seule batterie est en place. Système de protection de l’outil/de la batterie ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. L’outil est équipé d’un système de protection de l’outil/de la batterie. Ce système coupe automatiquement l’alimentation du moteur pour augmenter la durée de vie de l’outil et de la batterie.
Pour mettre l'outil en marche, appuyez simplement sur la gâchette. La vitesse de l'outil augmente à mesure que l'on accroît la pression exercée sur la gâchette. Pour l'arrêter, relâchez la gâchette. Indication de la puissance résiduelle de la batterie 1. Indicateur de batterie 2. Bouton CHECK 1 2 1 1. Bouton de verrouillage 1 1 015476 Appuyez sur le bouton de vérification pour que les indicateurs de batterie indiquent la capacité résiduelle de la batterie.
Avant de l’utiliser, réglez la longueur de la bandoulière pour vous permettre de travailler dans une position confortable. ASSEMBLAGE • UTILISATION ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant d'effectuer tout travail dessus. Soufflage Installation de l'embout allongé 2 2 1. Embout allongé 2. Triangle 015484 1 ATTENTION: Ne déposez pas le souffleur sur le sol tandis qu'il est en marche.
Nettoyage GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo Capacidades Longitud total XBU02 Volumen de aire (máx.) 13,4 m3/min (473 ft3/min) Velocidad del aire 54 m/s (120 MPH) (sin la boquilla grande) 585 mm (23") (con la boquilla grande) 830, 880, 930 mm (32-3/4", 34-3/4", 36-5/8") Tensión nominal 36 V c.c. Cartucho(s) de batería estándar Advertencia: Use solamente la(s) batería(s) indicada(s).
USB101-4 ADVERTENCIAS DE SEGURIDAD PARA LA SOPLADORA 1. 2. 3. 4. 5. 6. 7. 8. 9. Siempre use gafas protectoras, gorra y máscara al usar la sopladora. Los anteojos comunes o gafas oscuras NO son gafas de seguridad. Mientras opera el equipo, use siempre calzado resistente con suela antiderrapante y pantalón de trabajo. No use ropa holgada ni joyería que pudiera succionarse en la rendija de acceso de aire. Mantenga el cabello largo alejado de las rendijas de acceso de aire.
(2) Evite guardar el cartucho de batería en un cajón junto con otros objetos metálicos, tales como clavos, monedas, etc. (3) No exponga la batería de cartucho a la lluvia o nieve. Un corto circuito en la batería puede causar un flujo grande de corriente, sobrecalentamiento, posibles quemaduras y aún descomposturas. 6. No guarde la herramienta ni el cartucho de batería en lugares donde la temperatura pueda alcanzar o exceder los 50 ゚ C (122 ゚ F). 7.
caer al suelo causando una lesión a usted o alguien a su alrededor. • No instale el cartucho de batería a la fuerza: si el cartucho no se desliza al interior fácilmente, se debe a que no está siendo insertado correctamente. NOTA: • La herramienta no funciona con solo un cartucho de batería. DESCRIPCIÓN DEL FUNCIONAMIENTO • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta.
Para poner en marcha la herramienta, simplemente apriete el gatillo interruptor. La velocidad de la herramienta aumenta incrementando la presión en el gatillo. Suelte el gatillo interruptor para parar. Indicador de la capacidad restante de la batería 1. Indicador de batería 2. Botón de verificación “CHECK” 1 2 1 1. Botón de bloqueo 1 1 015476 Presione el botón de revisión para que los indicadores de la batería muestren la capacidad restante de las baterías.
Enganche la correa para hombro en el colgador de la herramienta. Antes de usar, ajuste la longitud de la correa de tal forma que resulte fácil la operación con ésta. ENSAMBLE • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier trabajo en la misma. OPERACIÓN Soplado Instalación de la boquilla larga 2 2 1. Boquilla larga 2.
Limpieza GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.