INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Impact Driver Atornillador de Impacto Inalámbrico XDT14 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities No load speed (RPM) Impacts per minute XDT14 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 14 mm (3/16" - 9/16") Hard impact mode 0 - 3,600 /min Medium impact mode 0 - 2,100 /min Soft impact mode 0 - 1,100 /min T mode 0 - 3,600 /min Hard impact mode 0 - 3,800 /min Medium impact mode 0 - 2,600 /min Soft impact mode 0 - 1,100 /min T mode 0 - 2,600 /
2. 3. 4. 5. 6. 7. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
Tips for maintaining maximum battery life revolutions or reciprocation per minute number of blow Important safety instructions for battery cartridge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
Overload protection CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.
NOTE: The tool automatically stops if you keep pulling the switch trigger for about 6 minutes. NOTE: To confirm the lamp status, pull the trigger. When the lamp lights up by pulling the switch trigger, the lamp status is ON. When the lamp does not come on, the lamp status is OFF. Electric brake NOTE: When the tool is overheated, the light flashes for one minute, and then the LED display goes off. In this case, cool down the tool before operating again. This tool is equipped with an electric brake.
Changing the impact force 2 3 T S H T S H 1 T T S S H H 4 6 T S H 5 ► 1. Changed in four steps 2. Hard 3. Medium 4. Soft 5. T mode 6. Button You can change the impact force in four steps: hard, medium, soft, and T mode. This allows a tightening suitable to the work. Every time the button is pressed, the number of blows changes in four steps. “T” is a special mode for fastening self drilling screws.
ASSEMBLY NOTE: If the driver bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the driver bit will not be secured. In this case, try re-inserting the bit according to the instructions above. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. NOTE: When it is difficult to insert the driver bit, pull the sleeve and insert it into the sleeve as far as it will go.
Proper fastening torque for standard bolt N•m (ft•lbs) 140 (101) NOTE: When fastening M8 or smaller screw, carefully adjust pressure on the switch trigger so that the screw is not damaged. M16(5/8") NOTE: Hold the tool pointed straight at the screw. M14(9/16") 120 (87) NOTE: If the impact force is too strong or you tighten the screw for a time longer than shown in the figures, the screw or the point of the driver bit may be overstressed, stripped, damaged, etc.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete Velocidad sin carga (rpm) Impactos por minuto XDT14 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 16 mm (3/16" - 5/8") Tornillo de alta resistencia 5 mm - 14 mm (3/16" - 9/16") Modo de impacto duro 0 r/min - 3 600 r/min Modo de impacto medio 0 r/min - 2 100 r/min Modo de impacto suave 0 r/min - 1 100 r/min Modo T 0 r/min - 3 600 r/min Modo de impacto duro 0 ipm - 3 800 ipm Modo d
4. 5. 6. No maltrate el cable. Nunca utilice el cable para transportar, jalar o desconectar la herramienta eléctrica. Mantenga el cable alejado del calor, aceite, objetos cortantes o piezas móviles. Los cables dañados o enredados aumentan el riesgo de sufrir una descarga eléctrica. Cuando utilice una herramienta eléctrica en exteriores, utilice un cable de extensión apropiado para uso en exteriores.
Servicio 1. Haga que una persona calificada repare la herramienta eléctrica utilizando sólo piezas de repuesto idénticas. Esto asegura que se mantenga la seguridad de la herramienta eléctrica. 2. Siga las instrucciones para la lubricación y cambio de accesorios. 3. Mantenga las agarraderas secas, limpias y sin aceite o grasa. Advertencias de seguridad para el atornillador de impacto inalámbrico 1. 2. 3. 4. 5. 6. Instrucciones importantes de seguridad para el cartucho de batería 1. 2. 3.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Luces indicadoras Iluminadas Apagadas Capacidad restante 1 Parpadeando 75% a 100% 50% a 75% 25% a 50% 0% a 25% Cargar la batería. ► 1. Marca de estrella La batería pudo haber funcionado mal. Accionamiento del interruptor NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Sistema de protección para la herramienta/batería 1 La herramienta está equipada con un sistema de protección de la herramienta/batería.
Accionamiento del conmutador de inversión de giro 1 A ► 1. Luz 1 T S H B ► 1. Palanca del interruptor de inversión PRECAUCIÓN: Confirme siempre la dirección de rotación antes de la operación. PRECAUCIÓN: Utilice el conmutador de inversión solamente después de que la herramienta haya parado completamente. Si cambia la dirección de rotación antes de que la herramienta haya parado podría dañarla.
Cambio de la fuerza de impacto 2 3 T S H T S H 1 T T S S H H 4 6 T S H 5 ► 1. Cambio a cuatro niveles 2. Alta 3. Media 4. Baja 5. Modo T 6. Botón La fuerza de impacto puede cambiarse a cuatro niveles: duro, medio, suave y modo T. Esto permite un apriete adecuado para el trabajo. Cada vez que el botón es oprimido, el número de percusiones cambia a cuatro niveles. El modo “T” es especial para la inserción de tornillos de autoperforación.
Para quitar la punta de destornillador, jale el mandril en dirección de la flecha y jale la punta de destornillador hacia afuera. MONTAJE PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería haya sido extraído antes de realizar cualquier trabajo en la misma.
Torsión de apriete apropiada para un tornillo estándar NOTA: Utilice la broca apropiada para la cabeza del tornillo/perno que desee utilizar. NOTA: Cuando inserte tornillos de 8 mm o un tornillo más pequeño, ajuste cuidadosamente la presión sobre el gatillo interruptor para evitar que el tornillo se dañe. 2 N•m (ft•lbs) 140 N•m (101 ft•lbs) 16 mm(5/8") NOTA: Sujete la herramienta dirigida en línea recta al tornillo.
ACCESORIOS OPCIONALES PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual. El empleo de cualquier otro accesorio o aditamento puede conllevar el riesgo de lesiones personales. Utilice los accesorios o aditamentos solamente para su fin establecido. Esta garantía le concede derechos legales específicos y usted podrá tener también otros derechos que varían de un estado a otro.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.