INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Recipro Saw Scie Recipro sans Fil Sierra Recíproca Inalámbrica XRJ06 IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ06 Length of stroke Strokes per minute 32 mm (1-1/4″) High (2) 0 - 3,000 /min Low (1) Max. cutting capacities 0 - 2,300 /min Pipe 130 mm (5-1/8″) Wood 255 mm (10″) Rated voltage D.C. 36 V Standard battery cartridge BL1815N, BL1820, BL1820B Overall length 449 mm (17-3/4″) Net weight • • • BL1830, BL1840, BL1850, BL1830B, BL1840B, BL1850B, BL1860B 4.0 kg (8.9 lbs) 4.6 kg (10.
6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Symbols CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. The followings show the symbols used for tool. volts direct current Tips for maintaining maximum battery life no load speed 1. revolutions or reciprocation per minute 2. Important safety instructions for battery cartridge 1. 2. 3.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. Indicating the remaining battery capacity To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
Lighting up the front lamp 3 1 1 2 ► 1 . Lock/speed change lever 2. Switch trigger 3. Status of the lock/speed change lever ► 1 . Lamp CAUTION: Do not look in the light or see the source of light directly. A Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out approximately 10 seconds after releasing the switch trigger. B NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp.
Hook CAUTION: When hanging the tool, set the lock/speed change lever in position to lock the switch trigger. (See the section titled “Switch action” .) 1 CAUTION: Never hang the tool at high or potentially unstable location. 2 3 ► 1 . Blade clamp lever 2. Released position 3. Fixed position Insert the recipro saw blade into the blade clamp as far as it will go. The blade clamp sleeve rotates and fixes the recipro saw blade.
MAINTENANCE CAUTION: Keep hands and fingers away from the lever during the switching operation. Failure to do so may cause personal injuries. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position .
PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle : XRJ06 Longueur de frappe Nombre de frappes par minute Capacités de coupe max. 32 mm (1-1/4″) Élevé (2) 0 - 3 000 /min Bas (1) 0 - 2 300 /min Tuyau 130 mm (5-1/8″) Bois 255 mm (10″) Tension nominale C.C.
3. 4. 5. 6. 7. Évitez les démarrages accidentels. Assurez-vous que l’interrupteur est en position d’arrêt avant de brancher l’outil à la prise de courant et/ou au blocpiles, et avant de prendre ou de transporter l’outil. Vous ouvrez la porte aux accidents si vous transportez les outils électriques avec le doigt sur l’interrupteur ou si vous les branchez alors que l’interrupteur est en position de marche. Retirez toute clé de réglage ou de serrage avant de mettre l’outil électrique sous tension.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. contre une partie du corps. Portez toujours des lunettes de sécurité ou des lunettes à coques. Les lunettes ordinaires et les lunettes de soleil NE sont PAS des lunettes de sécurité. Évitez les clous. Avant de commencer le travail, vérifiez la pièce pour en retirer tous les clous. Ne sciez pas de pièces dont le diamètre dépasse la capacité de coupe de la scie.
Conseils pour maintenir la durée de service maximale de la batterie 1. 2. 3. 4. Rechargez la batterie avant qu’elle ne soit complètement déchargée. Arrêtez toujours l’outil et rechargez la batterie quand vous remarquez que la puissance de l’outil diminue. Ne rechargez jamais une batterie complètement chargée. La surcharge réduit la durée de service de la batterie. Chargez la batterie à une température ambiante comprise entre 10 °C et 40 °C (50 °F et 104 °F).
Affichage de la charge restante de la batterie 3 Uniquement pour les batteries dont le numéro de modèle se termine par « B » 1 1 2 ► 1 . Levier de verrouillage/changement de vitesse 2. Gâchette 3. État du levier de verrouillage/changement de vitesse 2 ► 1 . Témoins indicateurs 2. Bouton de vérification Appuyez sur le bouton de vérification de la batterie pour afficher la charge restante de la batterie. Les témoins indicateurs s’allument pendant quelques secondes.
Allumage de la lampe avant Crochet ATTENTION : Lorsque vous accrochez l’outil, mettez le levier de verrouillage/changement de vitesse sur la position pour verrouiller la gâchette. (Voir la section intitulée « Interrupteur ».) 1 ATTENTION : N’accrochez jamais l’outil dans un emplacement élevé ou potentiellement instable. ► 1 . Lampe ATTENTION : Évitez de regarder directement le faisceau lumineux ou sa source. 1 Appuyez sur la gâchette pour allumer la lampe.
ATTENTION : Gardez les mains et les doigts à l’écart du levier pendant l’opération de changement. Autrement, il y a risque de blessures. 1 NOTE : Si vous retirez la lame de scie recipro sans faire complètement tourner le levier de serre-lame, il se peut que le levier ne soit pas verrouillé en position ouverte . Dans ce cas, faites complètement tourner le levier de serre-lame, puis assurez-vous qu’il est verrouillé en position ouverte . ► 1 . Levier de serre-lame 2. Position ouverte 3.
MAKITA NE SERA EN AUCUN CAS RESPONSABLE DE TOUS DOMMAGES INDIRECTS, ACCESSOIRES OU CONSÉCUTIFS DE LA VENTE OU DE L’UTILISATION DU PRODUIT. CET AVIS DE NONRESPONSABILITÉ S’APPLIQUE PENDANT ET APRÈS LA PÉRIODE COUVERTE PAR CETTE GARANTIE. MAKITA DÉCLINE TOUTE RESPONSABILITÉ QUANT À TOUTES GARANTIES IMPLICITES, Y COMPRIS LES GARANTIES DE « QUALITÉ MARCHANDE » OU D’« ADAPTATION À UN USAGE PARTICULIER » APRÈS LA PÉRIODE DE GARANTIE D’UN AN.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ06 Extensión de la carrera Carreras por minuto Capacidad máxima de corte 32 mm (1-1/4″) Alta (2) 0 cpm - 3 000 cpm Baja (1) 0 cpm - 2 300 cpm Tubo 130 mm (5-1/8″) Madera 255 mm (10″) Tensión nominal 36 V c.c.
2. 3. 4. 5. 6. 7. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Evite cortar clavos. Revise la pieza de trabajo y quite todos los clavos antes de utilizar la herramienta. No corte piezas de trabajo demasiado grandes. Compruebe que hay espacio suficiente más allá de la pieza de trabajo antes de cortar para que el disco no golpee el suelo, el banco de trabajo, etc. Sujete la herramienta con firmeza. Asegúrese de que el disco no esté haciendo contacto con la pieza de trabajo antes de activar el interruptor.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Si la herramienta no arranca, significa que la batería se sobrecalentó. En este caso, espere a que la batería se enfríe antes de volver a encender la herramienta.
Freno eléctrico La herramienta está equipada con un freno eléctrico. Si la herramienta falla constantemente en detenerse tras soltar el gatillo interruptor, lleve la herramienta a mantenimiento a un centro de servicio Makita. Iluminación de la luz delantera 1 1 2 ► 1 . Zapata 2. Palanca de ajuste de la zapata NOTA: La zapata no podrá ser ajustada si la palanca de ajuste de la zapata no se abre completamente.
Instalación o extracción de la segueta recíproca 2 PRECAUCIÓN: Limpie siempre las astillas y materias extrañas adheridas al disco y alrededor de la abrazadera de la segueta. En caso contrario, el disco podría quedar no bien apretado ocasionando lesiones graves.
GARANTÍA LIMITADA DE UN AÑO DE MAKITA Ésta Garantía no aplica para México Política de garantía MANTENIMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. AVISO: Nunca use gasolina, bencina, diluyente (tíner), alcohol o sustancias similares. Puede que esto ocasione grietas o descoloramiento.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.