INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Impact Driver Tournevis à Chocs sans Fil Atornillador de Impacto Inalámbrico XDT11 IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities XDT11 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 12 mm (3/16" - 1/2") No load speed (RPM) 0 - 2,900 /min Impacts per minute 0 - 3,500 /min Overall length 137 mm (5-3/8") Rated voltage Standard battery cartridge D.C. 18 V BL1815, BL1815N, BL1820, BL1820B BL1830, BL1840, BL1850, BL1840B, BL1850B 1.3 kg (2.8 lbs) 1.5 kg (3.
Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery. Switch action Indicating the remaining battery capacity Only for battery cartridges with "B" at the end of the model number 1 1 1. Switch trigger 2 1. Indicator lamps 2. Check button Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds.
Reversing switch action 1 A 2 B 1 1. Driver bit 2. Sleeve To install the driver bit, insert it into the sleeve as far as it will go. 1. Reversing switch lever CAUTION: Always check the direction of rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. CAUTION: When not operating the tool, always set the reversing switch lever to the neutral position.
The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation.
Replacing carbon brushes 1 1 1. Carbon brush cap 4. Make sure to place the lead wire in opposite side of the arm. 1. Limit mark Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. All carbon brushes should be replaced at the same time. Use only identical carbon brushes. 2 1. Use a screwdriver to remove two screws then remove the rear cover. 1 1 1. Lead wire 2. Carbon brush cap 5.
be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. implied warranty lasts, so the above limitation may not apply to you. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle : Capacités de serrage XDT11 Vis de mécanique 4 mm - 8 mm (5/32" - 5/16") Boulon standard 5 mm - 16 mm (3/16" - 5/8") Boulon à haute résistance 5 mm - 12 mm (3/16" - 1/2") Vitesse à vide (T/MIN) 0 - 2 900 /min Percussions par minute 0 - 3 500 /min Longueur totale 137 mm (5-3/8") Tension nominale Batterie standard Poids net • • • C.C.
Évitez les démarrages accidentels. Assurezvous que l’interrupteur est en position d’arrêt avant de brancher l’outil à la prise de courant et/ou au bloc-piles, et avant de prendre ou de transporter l’outil. Vous ouvrez la porte aux accidents si vous transportez les outils électriques avec le doigt sur l’interrupteur ou si vous les branchez alors que l’interrupteur est en position de marche. 4. Retirez toute clé de réglage ou de serrage avant de mettre l’outil électrique sous tension.
6. être extrêmement chauds et vous brûler la peau. Gardez les mains éloignées des pièces en rotation. CONSERVEZ CES INSTRUCTIONS. MISE EN GARDE : NE vous laissez PAS tromper (au fil d’une utilisation répétée) par un sentiment d’aisance ou de familiarité avec le produit en négligeant les consignes de sécurité qui accompagnent le produit. UNE UTILISATION INCORRECTE ou le non-respect des règles de sécurité énoncées dans le présent manuel d’instructions peut provoquer des blessures graves.
Dans cette situation, libérez la gâchette et arrêtez l’activité qui entraîne une surcharge de l’outil. Ensuite, appuyez de nouveau sur la gâchette pour redémarrer. Si l’outil ne démarre pas, la batterie est en surchauffe. Dans cette situation, laissez refroidir la batterie avant d’appuyer de nouveau sur la gâchette. Tension de la batterie faible : La charge restante de la batterie est trop faible pour que l’outil puisse fonctionner. Dans cette situation, retirez et rechargez la batterie. 1 2 3 1.
Interrupteur Fonctionnement de l’inverseur A B 1 1 1. Gâchette ATTENTION : Avant d’insérer la batterie dans l’outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d’arrêt lorsque libérée. Pour mettre l’outil en marche, appuyez simplement sur la gâchette. La vitesse de l’outil augmente à mesure que l’on accroît la pression exercée sur la gâchette. Pour arrêter l’outil, libérez la gâchette. Allumage de la lampe avant 1.
Utilisez uniquement l’embout-tournevis ou l’embout-douille indiqué sur la figure. N’utilisez aucun autre embout-tournevis ou embout-douille. Installation du crochet 1 1 2 2 3 1. Embout-tournevis 2. Manchon Pour installer l’embout-tournevis, insérez-le à fond dans le manchon. 1. Rainure 2. Crochet 3. Vis L’outil est équipé d’un crochet pratique qui permet de le suspendre temporairement. Il s’installe d’un côté comme de l’autre de l’outil.
1. M14(9/16") M16(5/8") M12(1/2") M14(9/16") 60 (43) 40 (29) 20 (14) M10(3/8") M12(1/2") M8(5/16") 0 1,0 2,0 Temps de serrage (s) Couple de serrage Boulon à haute résistance N•m (ft•lbs) 160 (116) 140 (101) 120 (87) 100 (72) 80 (58) M8(5/16") 60 (43) 40 (29) 20 (14) 0 M10(3/8") M8(6/16") 1,0 2. Couple de serrage adéquat 80 (58) M16(5/8") 3,0 3. 4. 5.
2 1 1 2 1. Couvercle arrière 2. Vis 1. Fil de sortie 2. Capuchon de charbon 2. Soulevez le bras du ressort puis placez-le dans la partie creuse du boîtier à l’aide d’un tournevis à pointe plate et tige mince, ou d’un outil similaire. 5. Assurez-vous que les capuchons de charbon sont bien verrouillés dans les orifices des porte-charbons. 1 1 2 2 3 1. Orifice 1. Partie creuse 2. Ressort 3. Bras 3. Utilisez une paire de pinces pour retirer les capuchons de charbon.
Si vous désirez obtenir plus de détails sur ces accessoires, veuillez contacter le centre de service aprèsvente Makita le plus près. • Embouts-tournevis • Crochet • Mallette de transport en plastique • Chargeur et batterie authentiques Makita • Protecteur de batterie NOTE : Certains éléments de la liste peuvent être inclus avec l’outil comme accessoires standards. Ils peuvent varier suivant les pays.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete XDT11 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 16 mm (3/16" - 5/8") Tornillo de alta resistencia 5 mm - 12 mm (3/16" - 1/2") Velocidad sin carga (rpm) 0 - 2 900 r/min Impactos por minuto 0 - 3 500 ipm Longitud total 137 mm (5-3/8") Tensión nominal Cartucho de batería estándar Peso neto • • • 18 V c.c.
zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. 3. Impida el encendido accidental. Asegúrese de que el interruptor esté en la posición de apagado antes de conectar a la alimentación eléctrica y/o de colocar el cartucho de batería, así como al levantar o cargar la herramienta.
6. extremadamente calientes y provocarle una quemadura. Mantenga las manos alejadas de las piezas giratorias. GUARDE ESTAS INSTRUCCIONES. ADVERTENCIA: NO DEJE que la comodidad o familiaridad con el producto (a base de utilizarlo repetidamente) evite que siga estrictamente las normas de seguridad para dicho producto. El USO INCORRECTO o el no seguir las normas de seguridad indicadas en este manual de instrucciones puede ocasionar lesiones graves.
1 2 3 1. Indicador rojo 2. Botón 3. Cartucho de batería Para quitar el cartucho de batería, deslícelo de la herramienta mientras desliza el botón sobre la parte delantera del cartucho. Para colocar el cartucho de batería, alinee la lengüeta sobre el cartucho de batería con la ranura en la carcasa y deslice en su lugar. Inserte por completo hasta que se fije en su lugar con un pequeño clic. Si puede ver el indicador rojo del lado superior del botón, esto indica que no ha quedado fijo por completo.
NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Accionamiento del interruptor de inversión Accionamiento del interruptor A B 1 1 1. Gatillo interruptor PRECAUCIÓN: Antes de insertar el cartucho de batería en la herramienta, compruebe siempre y cerciórese de que el gatillo interruptor se acciona debidamente y que vuelve a la posición “OFF” (apagado) cuando lo suelta.
Instalación o extracción de la punta de destornillador/punta de atornillar 12 mm (15/32”) 9 mm (3/8”) NOTA: Si la punta de destornillador no se encuentra insertada hasta el fondo en el mandril, éste no regresará a su posición original y la punta de destornillador no quedará asegurada. En este caso, procure insertar la broca de nuevo siguiendo las instrucciones de arriba. NOTA: Si tiene dificultades para insertar la punta de destornillador, jale el mandril e inserte la broca tanto como sea posible.
1. 100 N•m (72 ft•lbs) 80 N•m (58 ft•lbs) 16 mm(5/8") 14 mm(9/16") 2. Torsión de apriete adecuada Torsión de apriete Tornillo estándar N•m (ft•lbs) 140 N•m (101 ft•lbs) 120 N•m (87 ft•lbs) 16 mm(5/8") 12 mm(1/2") 14 mm(9/16") 60 N•m (43 ft•lbs) 10 mm(3/8") 40 N•m (29 ft•lbs) 20 N•m (14 ft•lbs) 12 mm(1/2") 8 mm(5/16") 0 1,0 s 10 mm(3/8") 8 mm(6/16") 2,0 s 3,0 s 4. Tiempo de apriete (s) 1,0 s 2,0 s 5.
2 1 1 2 1. Cubierta posterior 2. Tornillo 1. Cable conductor 2. Tapa de las escobillas de carbón 2. Levante la parte del brazo del resorte y después póngalo en la parte empotrada del alojamiento con un destornillador de punta plana de eje largo y fino o similar. 5. Asegúrese de que las tapas de las escobillas de carbón hayan encajado en forma segura en los orificios de los portaescobillas. 1 2 1 2 3 1. Parte empotrada 2. Resorte 3. Brazo 1. Orificio 3.
ACCESORIOS OPCIONALES consecuentes, por lo que la limitación o exclusión arriba mencionada podría no aplicar para usted. Algunos estados no permiten la limitación sobre la duración de una garantía implícita, por lo que la limitación arriba mencionada podría no aplicar para usted. PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL Cordless Angle Grinder XAG03 XAG04 015078 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model XAG03 XAG04 Wheel diameter 115 mm (4-1/2") 125 mm (5") Max. wheel thickness 6 mm (1/4") Spindle thread Rated speed (n) / No load speed (n0) Overall length Net weight 6 mm (1/4") 5/8" 8,500 /min With battery cartridge BL1815N, BL1820 348 mm (13-3/4") With battery cartridge BL1830, BL1840, BL1850 362 mm (14-1/4") With battery cartridge BL1815N, BL1820 2.3 kg (5.0 lbs) With battery cartridge BL1830, BL1840, BL1850 2.5 kg (5.5 lbs) 2.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
5. 6. 7. 8. 9. 10. 11. 12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 13. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 14. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 15.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. ENC007-8 Do not leave the tool running. Operate the tool only when hand-held. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. Use only flanges specified for this tool.
FUNCTIONAL DESCRIPTION • 1. Slide switch 1 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 015082 1. Button 2. Red indicator 3. Battery cartridge 1 To start the tool, slide the slide switch toward the "I (ON)" position by pushing the rear of the slide switch. For continuous operation, press the front of the slide switch to lock it.
Releasing protection lock When the protection system works repeatedly, the tool is locked and the battery indicator shows the following state. Automatic speed change function 1. Mode indicator 1 Battery indicator On Off Blinking Protection lock works 015200 In this situation, the tool does not start even if turning the tool off and on. To release the protection lock, remove the battery, set it to the battery charger and wait until the charging finishes.
For tool with locking screw type wheel guard Installing or removing wheel guard (For depressed center wheel, multi disc / abrasive cut-off wheel, diamond wheel) 1. Wheel guard 2. Bearing box 3. Screw WARNING: When using a depressed center grinding wheel/Multi-disc, wire wheel brush, cut-off wheel or diamond wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
Grinding and sanding operation Installing or removing abrasive disc (optional accessory) 1 2 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad 3 A B 015097 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.
Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel/diamond wheel 1 2 3 4 010855 Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Mount the inner flange and abrasive cut-off / diamond wheel onto the spindle. Tighten the lock nut securely with supplied wrench.
Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc and wire wheel brush.
1 6 2 3 7 4 8 2 11 10 9 3 12 5 5 115 mm (4-1/2") model 1 2 3 125 mm (5") model Grip 36 Wheel Guard (for grinding wheel) Inner flange 45 Inner flange 45 4 Depressed center wheel/Multi-disc 5 Lock nut 5/8-45 Lock nut 5/8-45 6 Rubber pad 100 Rubber pad 115 7 8 Abrasive disc Sanding lock nut 5/8-48 9 Sanding lock nut 5/8-48 Wire wheel brush 10 Wire cup brush 11 Wheel Guard (for cut-off wheel) 12 - Abrasive cut-off wheel/Diamond wheel Lock nut wrench 28 Lock nut wrench 28 01530
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
EN Job Site Radio Instruction manual FRCA Radio de chantier Manuel d’instructions ESMX Radio de Trabajo Manual de instrucciones XRM05 IMPORTANT: Read Before Using. IMPORTANT : Lisez les instructions avant l’utilisation. IMPORTANTE: Leer antes de usar.
12 10 2 3 14 1 4 5 6 7 8 9 (22) (21) 13 L K A B C J PM I D 20 H E G F 11 (23) 1 2 (24)
14 15 15 11 15 15 16 2 3 17 18 19 17 18 4 5 19 19 6 19 7 3
10 25 26 8 9 10 8 9 10 4 11
ENGLISH (Original instructions) IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: 1. Read this instruction manual and the charger instruction manual carefully before use. 2. Clean only with dry cloth. 3. Do not block any ventilation opening. Install in accordance with the manufacturer’s instruction. 4.
Features: • • • • • • • • • • • AM/FM-stereo PLL Synthesized Large LCD display with illumination Manual/Preset/Scan tuning Rotary tuning and volume control 5 preset stations each band Time and 2 alarm timers (radio and HWS buzzer) with Snooze Adjustable sleep (auto shut off) timer Stereo speaker for rich sound performance Ultra rugged design Water resistant to IPX 4 Powered by both Makita battery pack and supplied power adaptor Explanation of general view (Fig. 1) Controls: 1. Power and Sleep timer 2.
Note: Table regarding to the battery operating time above is for reference. The actual operating time may differ with the type of the battery, charging condition, or usage environment. Indicator lamps Remaining capacity Lighted Off Blinking Installing or removing Slide battery cartridge (Fig. 4 & 5) 75% to 100% • To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place.
3. Long press the time set button for more than 2 seconds, display will flash time set symbol and also the hour digit, followed by a beep. 4. Rotate Tuning/Volume control knob to set the required hour. 5. Press button to confirm hour setting, the minute digit will flash. 6. Rotate Tuning/Volume control knob to set the required minute. 7. Press the button again to complete clock setting. Operating the radio This radio equips with three tuning methods - Scan tuning, Manual tuning and Memory presets recall.
b. Setting radio alarmed station 1. During setting radio alarm time and radio alarm symbol is flashing, press Band button to activate the radio to select required wake-up band and station by manual tuning and recall the preset stations. Press button to complete radio alarm setting. Display will show . 2. When above radio alarm time and station are set, press and hold down radio alarm button for 2 seconds followed by a beep to switch alarm on or off. Display will show when radio alarm is set.
Dimension (W x H x D) in mm 280 x 302 x 163 (11” x 11-7/8” x 6-3/8”) Weight Battery cartridge (kg) (Without battery) BL0715 BL7010 (lbs) 4.0 8.9 4.1 9.1 4.2 9.3 4.3 9.5 4.4 9.7 4.5 10.0 4.6 10.
FRANÇAIS (Mode d’emploi original) CONSIGNES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT : Lors de l’utilisation d’outils électriques, il faut toujours prendre des précautions élémentaires de sécurité, dont les suivantes, pour réduire les risques d’incendie, de décharge électrique et de blessure. 1. Lisez attentivement ce manuel d’instructions et celui du chargeur avant l’utilisation. 2. Nettoyez uniquement avec un chiffon sec. 3. Ne bloquez aucun orifice de ventilation.
Pour les États-Unis : Attention à l’intention de l’utilisateur Tout changement ou modification non expressément approuvés par la partie responsable de la conformité peut entraîner l’annulation du droit de l’utilisateur à utiliser cet appareil.
les polarités comme indiqué dans le compartiment. Remettre le couvercle. 3. Après avoir introduit les batteries de secours, mettre les batteries principales dans la radio. Les batteries compatibles pour cette radio sont répertoriées dans le tableau suivant. Le tableau suivant indique le temps de fonctionnement par charge.
0 % à 25 % 2. A l’écran apparaît « -: - - » quand les batteries de secours sont installées. 3. Appuyer sur le bouton de réglage de l’heure plus de 2 secondes. Le symbole clignote à l’écran, ainsi que le chiffre des heures, suivi d’un bip. 4. Tourner le bouton de commande Réglage/Volume pour sélectionner l’heure. 5. Appuyer sur le bouton pour confirmer. Le chiffre des minutes clignote. 6. Tourner le bouton de commande Réglage/Volume pour sélectionner la minute. 7.
2. Sélectionner la bande de fréquence en appuyant sur le bouton de fréquence. Régler l’antenne comme indiqué ci-dessus. 3. Une simple rotation du bouton de commande Réglage/Volume modifiera la fréquence : FM : 50 ou 100 kHz AM (MW) : 9 ou 10 kHz Remarque : Si le volume de la radio est préréglé, appuyer sur le bouton de réglage pour avoir un nouveau statut. 4. Tourner le bouton de commande Réglage/Volume jusqu’à ce que la fréquence requise apparaisse sur l’écran. 5.
Fonction « Sieste » 1. Quand l’alarme fonctionne, appuyer sur n’importe quel bouton, sauf le bouton de mise en marche, pour arrêter l’alarme. L’alarme radio ou le buzzer reste silencieux par intervalle de 5 minutes. 2. Le symbole « sieste » et le symbole d’alarme clignotent à l’écran. La fonction « sieste » peut être active pendant une heure. Fonction « Sommeil » La fonction de sommeil arrête automatiquement la radio en fonction de l’heure choisie pour l’arrêt. 1.
Poids Batterie (kg) (lbs) (sans batterie) 4,0 8,9 4,1 9,1 4,2 9,3 4,3 9,5 4,4 9,7 4,5 10,0 4,6 10,2 BL0715 BL7010 BL1014 BL1016 BL1021B BL1415 BL1415N BL1041B BL1815 BL1815N BL1820 BL1820B BL1430 BL1430B BL1440 BL1450 BL1460B BL1830 BL1830B BL1840 BL1840B BL1850 BL1850B BL1860B 17
ESPAÑOL (Instrucciones originales) INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA: Cuando utilice herramientas eléctricas, deberá tomar siempre precauciones de seguridad básicas, incluyendo las siguientes, para reducir el riesgo de incendios, descargas eléctricas y heridas personales: 1. Lea este manual de instrucciones y el manual de instrucciones del cargador con cuidado antes de usar. 2. Limpie sólo con un paño limpio. 3. No obstruya ninguna apertura de ventilación.
Para Estados Unidos: Precauciones para el usuario Los cambios o modificaciones que no hayan sido expresamente autorizados por la entidad responsable por el cumplimiento de las regulaciones podrían anular la autoridad del usuario de utilizar este equipo.
2. Retire la cubierta del compartimento para pilas de respaldo e inserte 2 pilas nuevas UM-3 (tamaño AA). Asegúrese de colocar las pilas con la polaridad correcta como se indica adentro del compartimento. Vuelva a colocar la cubierta de batería. 3. Una vez colocadas las pilas de respaldo, inserte el paquete de baterías principal que alimentará la radio. Los paquetes de baterías adecuados para esta radio se listan en la tabla que se muestra a continuación.
Luces indicadoras Capacidad restante Encendidas Apagadas Parpadeando 75% a 100% 50% a 75% 25% a 50% 0% a 25% Recargue la batería. Puede que haya habido un mal funcionamiento de la batería. 2. La pantalla mostrará “-: - -” cuando al colocar las pilas de respaldo. 3. Presione prolongadamente el botón para el ajuste hora durante más de 2 segundos, la pantalla mostrará el símbolo de ajuste , así como el dígito para la hora seguido de un pitido. 4.
5. Para apagar la radio, presione el botón encendido. La pantalla mostrará “OFF”. Sintonía manual 1. Presione el botón de encendido de la radio para encenderla. 2. Seleccione la banda de frecuencia requerida al presionar el botón para la banda de frecuencia. Ajuste la antena como se describe anteriormente. 3.
El pitido de la alarma se acortará cada 15 segundos durante un minuto seguido de un minuto de silencio antes de que el ciclo se repita. La alarma de timbre HWS continuará sonando durante una hora, salvo que sea apagada mediante el botón de encendido. Al presionar el botón de encendido mientras la alarma se encuentra sonando cancelará su funcionamiento por un periodo de 24 horas. 1. La alarma de timbre HWS puede ajustarse ya sea con la radio encendida o apagada. 2.
Terminal de entrada 3,5 mm de dia.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Metal Cutter Scie Circulaire à Métaux Sans Fils Cortadora de Metal Inalámbrico XSC01 007522 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XSC01 Blade diameter 136 mm (5-3/8") Max. Cutting depth 51 mm (2") No load speed (RPM) 3,600 /min Overall length 348 mm (13-3/4") Net weight 2.3 kg (5.1 lbs) Rated voltage 2.6 kg (5.7 lbs) D.C. 18 V Standard battery cartridges BL1815N BL1830 / BL1840 • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Service 28. Have your power tool serviced by a qualified repair person using only identical replacement parts.
Lower guard function 16. Intended use This tool is intended to cut mild steel only. 17. Check lower guard for proper closing before each use. Do not operate the tool if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If tool is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting lever and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. 18.
28. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 ゚ C (122 ゚ F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10.
FUNCTIONAL DESCRIPTION • Lithium-ion batteries with a star marking are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: • Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current.
Switch action 1 CAUTION: Do not look in the light or see the source of light directly. Only to turn on the light, pull the switch trigger without pressing the lock-off lever. To turn on the light and run the tool, press the lock-off lever and pull the switch trigger with the lock-off lever being pressed. 1. Switch trigger 2. Lock-off lever 2 • NOTE: • Use a cotton stick to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
When changing blade, make sure to also clean the upper and lower blade guards of accumulated sawdust as discussed in the Maintenance section. Such efforts do not replace the need to check lower guard operation before each use. move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the cutting is completed. To get clean cuts, keep your cutting line straight and your speed of advance uniform.
MAINTENANCE • • • Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. After replacing brushes, insert the battery cartridge into the tool and break in brushes by running tool with no load for about 1 minute. Then check the tool while running and electric brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XSC01 Diamètre de la lame 136 mm (5-3/8") Profondeur de coupe max. 51 mm (2") Vitesse à vide (T/MIN) 3 600 /min Longueur totale 348 mm (13-3/4") Poids net 2,3 kg (5,1 lbs) Tension nominale 2,6 kg (5,7 lbs) C.C. 18 V Batteries standard BL1815N BL1830 / BL1840 • Étant donné l'évolution constante de notre programme de recherche et de développement, les spécifications contenues dans ce manuel sont sujettes à modification sans préavis.
présentes instructions d'utilisation. Les outils électriques représentent un danger entre les mains de personnes qui n'en connaissent pas le mode d'utilisation. 21. Veillez à l’entretien des outils électriques. Assurez-vous que les pièces mobiles ne sont pas désalignées ou coincées, qu’aucune pièce n’est cassée et que l’outil électrique n’a subi aucun dommage affectant son bon fonctionnement. Le cas échéant, faites réparer l'outil électrique avant de l'utiliser.
29. 30. − Lorsque la lame se trouve coincée ou pincée fermement par le trait de scie qui se referme sur elle, elle se bloque et une réaction du moteur entraîne alors l'outil rapidement vers l'utilisateur. − Si la lame se tord ou se désaligne par rapport à la ligne de coupe, les dents arrière risquent de s'enfoncer dans la surface de la pièce et la lame de quitter le trait de scie en reculant brusquement vers l'utilisateur.
lame peut accrocher des objets cachés en dépassant de l'autre côté de la surface, entraînant un recul. Pour les coupes en plongée, rétractez le protecteur inférieur à l'aide de la poignée de rappel. Fonction du protecteur inférieur 16. Utilisation prévue Cet outil est destiné à la coupe d'acier doux uniquement. 17. Avant chaque utilisation, assurez-vous que le protecteur inférieur se referme correctement.
DESCRIPTION DU FONCTIONNEMENT 3. Cessez immédiatement l'utilisation si le temps de fonctionnement devient excessivement court. Il y a risque de surchauffe, de brûlures, voire d'explosion. 4. Si l'électrolyte pénètre dans vos yeux, rincez-les à l'eau claire et consultez immédiatement un médecin. Il y a risque de perte de la vue. 5. Ne court-circuitez pas la batterie : (1) Ne touchez les bornes avec aucun matériau conducteur.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) réduire les risques de chocs en retour dangereux qui peuvent causer des blessures. Visée 1. Étoile 1 1. Position A 2. Ligne de coupe 3. Base 2 1 3 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection. Ce système coupe automatiquement l’alimentation de l’outil pour augmenter la durée de vie de la batterie.
Le mécanisme de frein à lame ne doit pas être utilisé en remplacement du garde inférieur. N'UTILISEZ JAMAIS L'OUTIL LORSQUE LE GARDE INFÉRIEUR NE FONCTIONNE PAS. CELA COMPORTE DES RISQUES DE BLESSURE GRAVE. ATTENTION: Assurez-vous que la lame est installée avec les dents orientées vers le haut à l'avant de l'outil. • Utilisez exclusivement une clé Makita pour installer ou retirer la lame.
• • • • accidentellement de l'outil, en vous blessant ou en blessant une personne se trouvant près de vous. Assurez-vous de déplacer l'outil doucement vers l'avant, en ligne droite. Le fait de forcer ou de tordre l'outil entraînera une surchauffe du moteur et un dangereux choc en retour, risquant de provoquer une blessure grave. Si l'outil est utilisé de manière continue jusqu'à ce que la batterie soit déchargée, laissez-le reposer 15 minutes avant de poursuivre l'opération avec une batterie fraîche.
• Après avoir remplacé les charbons, insérez la batterie dans l'outil et rodez les brosses en faisant fonctionner l'outil à vide pendant environ 1 minute. Vérifiez ensuite le bon fonctionnement de l'outil, ainsi que l'activation du frein électrique lors du relâchement de la gâchette. Si le frein électrique ne fonctionne pas bien, faites une demande de réparation auprès du centre de service après-vente Makita le plus près.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XSC01 Diámetro del disco 136 mm (5-3/8") Profundidad de corte máxima 51 mm (2") Velocidad sin carga (RPM) 3 600 r/min Longitud total 348 mm (13-3/4") Peso neto 2,3 kg (5,1 lbs) Tensión nominal 2,6 kg (5,7 lbs) 18 V c.c. Cartuchos de batería estándar BL1815N BL1830 / BL1840 • Debido a nuestro programa continuo de investigación y desarrollo, las especificaciones aquí dadas están sujetas a cambios sin previo aviso.
21. Realice el mantenimiento a las herramientas eléctricas. Compruebe que no haya partes móviles desalineadas o estancadas, piezas rotas y cualquier otra condición que pueda afectar al funcionamiento de la herramienta eléctrica. Si la herramienta eléctrica está dañada, haga que se la reparen antes de utilizarla. Muchos accidentes son ocasionados por herramientas eléctricas con un mal mantenimiento. 22. Mantenga las herramientas de corte limpias y filosas.
29. 30. − Cuando el disco está mellado o aprisionado por la entalladura al cerrarse, se atasca y la reacción del motor empuja la unidad rápidamente hacia atrás, hacia el operador. − Si el disco se retuerce o está mal alineado en el corte, los dientes del borde posterior del disco pueden clavarse en la superficie posterior de la pieza de trabajo, haciendo que el disco escale la entalladura y salte hacia el operador.
el protector inferior utilizando el mango retráctil. Función del protector inferior (guarda del disco) 16. Uso pretendido Esta herramienta está diseñada para cortar acero dulce solamente. 17. Compruebe si el protector inferior está bien cerrado antes de cada uso. No utilice la herramienta si el protector inferior no se mueve libremente y/o no se cierra instantáneamente. Nunca sujete ni mantenga el protector inferior en la posición abierta.
DESCRIPCIÓN DEL FUNCIONAMIENTO 4. En caso de que ingresen electrolitos en sus ojos, enjuáguelos bien con agua limpia y consulte de inmediato a un médico. Podría perder la visión. 5. No cortocircuite el cartucho de batería: (1) No toque las terminales con ningún material conductor. (2) Evite guardar el cartucho de batería en un cajón junto con otros objetos metálicos, tales como clavos, monedas, etc. (3) No exponga la batería de cartucho a la lluvia o nieve.
Sistema de protección de batería (batería de ión de litio con marca de estrella) Para obtener cortes más limpios y seguros, ajuste la profundidad de corte de forma que no sobresalga más de un diente del disco de sierra por debajo de la pieza de trabajo. La utilización de una profundidad de corte apropiada ayuda a reducir la posibilidad de que se produzcan peligrosos RETROCESOS BRUSCOS que pueden ocasionar heridas personales. 1. Marca de estrella 1 Guía visual 1. Posición A 2. Línea de corte 3.
Extracción e instalación del disco cortador NUNCA fije con cinta adhesiva ni impida el funcionamiento ni la finalidad de la palanca de bloqueo. • 1. Bloqueo del eje 2. Llave hexagonal Freno eléctrico Esta herramienta está equipada con un freno eléctrico para el disco. Si sistemáticamente ocurre que al soltar el gatillo interruptor el disco no se detiene de inmediato, envíe la herramienta al centro de servicio Makita para su reparación.
OPERACIÓN • • • • • detenga y después retire la herramienta. Vuelva a alinear la herramienta sobre una nueva línea de corte, y comience a cortar de nuevo. Procure evitar reposicionar la herramienta lo cual expone al operador a las partículas y residuos que se expulsan de la misma. Use protección para los ojos para evitar lesiones.
MANTENIMIENTO • • • 1 PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. Limpie los protectores superior e inferior para asegurar que no haya aserrín acumulado, lo cual puede que impida la operación del sistema inferior de protección. Un sistema de protección sucio puede que limite la operación adecuada, lo cual podría resultar en graves lesiones al operador.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
31
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
GB Rechargeable Flashlight Instruction manual F Lampe torche Manuel d’instructions E Linterna recargable Manual de instrucciones DML145/DML185
3 2 4 1 1 2 5 6 3 4 7 5 2
Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning be-fore use. Symboles Les symboles utilisés pour l’appareil sont indiqués ci-dessous. Assurez-vous d’avoir bien compris leur signification avant l’utilisation. Símbolos Se utilizan los siguientes símbolos para el equipo. Asegúrese de que comprende su significado antes del uso. ❏ Read instruction manual. ❏ Veuillez lire le manuel d’instructions. ❏ Lea el manual de instrucciones.
ENGLISH Explanation of general view 1. 2. 3. 4. 5. 6. Battery cartridge Button Red part 7. Switch Ring Bulb Shoulder strap SPECIFICATIONS Model DML145 DML185 Bulb 12 V 0.7 A 18 V 0.6 A Dimensions (without battery) Net weight (with battery) L 284 mm (11 - 1/8”) 284 mm (11 - 1/8”) W 84 mm (3 - 5/16”) 84 mm (3 - 5/16”) H 96 mm (3 - 3/4”) 96 mm (3 - 3/4”) BL1415/BL1415N 0.66 kg (1.44 lbs) BL1430/BL1440 0.85 kg (1.87 lbs) BL1815/BL1815N/BL1820 0.71 kg (1.57 lbs) BL1830/BL1840 0.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge.
FRANÇAIS Descriptif 1. 2. 3. 4. 5. 6. Batterie Bouton Partie rouge 7.
DESCRIPTION DU FONCTIONNEMENT Angle de tête (Fig. 2) L’angle de tête peut être réglé sur l’une ou l’autre de quatre positions. Réglez-le selon vos besoins. Charge Avant l’utilisation, chargez la batterie avec le chargeur Makita. Installation et retrait de la batterie (Fig.1) • Mettez toujours l’outil hors tension avant d’insérer ou de retirer la batterie. • Pour retirer la batterie, sortez-la de l’outil tout en faisant glisser le bouton à l’avant de la batterie.
ESPAÑOL Explicación de los dibujos 1. 2. 3. 4. 5. 6. Cartucho de la batería Botón Parte roja 7.
DESCRIPCIÓN DEL FUNCIONAMIENTO Ángulo de la cabeza (Fig. 2) El ángulo de la cabeza se puede ajustar en cuatro posiciones. Ajústelo como desee. Carga Cargue el cartucho de la batería con el cargador de Makita antes de su uso. Instalación o extracción del cartucho de la batería (Fig. 1) • Apague siempre la herramienta antes de insertar o extraer el cartucho de la batería.
10
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885246-944 ALA www.makita.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Blower ASPIRO / SOUFFLEUR (SANS FIL) Sopladora Inalámbrica DUB142 DUB182 008308 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities DUB142 Air pressure (water column) DUB182 0 - 550 mm (21-5/8") 3 0 - 2.6 m /min Air volume No load speed (RPM) 0 - 18,000 /min Overall length 507 mm (20") 509 mm (20") 523 mm (20-5/8") 525 mm (20-3/4") Net weight 1.6 kg (3.5 lbs) 1.8 kg (3.9 lbs) 1.6 kg (3.6 lbs) 1.9 kg (4.1 lbs) Rated voltage D.C. 14.4 V BL1415 / BL1415N Standard battery cartridges BL1430 / BL1440 / BL1450 D.C.
USD301-1 WARNING: Symbols MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. The followings show the symbols used for tool. ・ volts ENC007-5 IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. 2. 3. 4. 5. 6. 7. 8. 9. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge.
Dust suction 1. Pointer 2. Air volume adjusting dial 3. Switch trigger 1 1 2 2 3 3 008313 4 To start the tool, simply pull the switch trigger. Air volume is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Air volume adjusting dial Air volume can be adjusted to any of three settings by turning the adjusting dial with the switch trigger fully depressed. Refer to the table below for the relationship between the number on the dial and the air volume.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle DUB142 Pression d'air (colonne d'eau) Capacités DUB182 0 - 550 mm (21-5/8") 3 0 - 2,6 m /min Volume d'air Vitesse à vide (T/MIN) 0 - 18 000 /min Longueur totale 507 mm (20") 509 mm (20") 523 mm (20-5/8") 525 mm (20-3/4") Poids net 1,6 kg (3,5 lbs) 1,8 kg (3,9 lbs) 1,6 kg (3,6 lbs) 1,9 kg (4,1 lbs) Tension nominale C.C. 14,4 V BL1415 / BL1415N Batteries standard BL1430 / BL1440 / BL1450 C.C.
2. 3. 4. 5. 6. 7. 8. Portez toujours des lunettes de sécurité, un casque et un masque antipoussières lorsque vous utilisez le souffleur. Les lunettes ordinaires et les lunettes de soleil ne sont PAS des lunettes de sécurité. Ne pointez jamais la buse vers les personnes présentes lorsque vous utilisez le souffleur. Utilisez toujours le sac à poussière lorsque vous aspirez des poussières, copeaux et matières similaires.
Pour faire démarrer l’outil, appuyez simplement sur la gâchette. Le volume d’air augmente à mesure que vous augmentez la pression sur la gâchette. Pour arrêter l'outil, relâchez la gâchette. Sélecteur de volume d’air Il est possible de choisir l’un ou l’autre des trois réglages du volume d’air en tournant le sélecteur avec la gâchette entièrement enfoncée. Reportez-vous au tableau ci-dessous pour connaître le lien entre le chiffre sur le sélecteur et le volume d’air.
Aspiration des poussières 1 2 3 Nettoyage 1. Sac à poussières 2. Sortie d'air du souffleur 3. Entrée d'aspiration 4. Buse 4 012984 012985 Pour aspirer les poussières, insérez le bec à poussières dans la prise d'aspiration et le sac à poussières dans la prise de sortie de la soufflerie. Lorsque le sac est rempli de poussières, ouvrez la glissière pour le vider dans une poubelle. De temps à autre, essuyez la surface extérieure de l'outil à l'aide d'un chiffon trempé dans une eau savonneuse.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo DUB142 Presión de aire (columna de agua) Capacidades DUB182 0 - 550 mm (21-5/8") 3 0 - 2,6 m /min Volumen de aire Velocidad sin carga (r.p.m.) 0 - 18 000 r/min Longitud total 507 mm (20") 509 mm (20") 523 mm (20-5/8") 525 mm (20-3/4") Peso neto 1,6 kg (3,5 lbs) 1,8 kg (3,9 lbs) 1,6 kg (3,6 lbs) 1,9 kg (4,1 lbs) Tensión nominal 14,4 V c.c. BL1415 / BL1415N Cartuchos de batería estándar BL1430 / BL1440 / BL1450 18 V c.c.
2. 3. 4. 5. 6. 7. 8. Siempre use gafas protectoras, gorra y máscara al usar la sopladora. Las gafas normales o las gafas de sol NO constituyen gafas de seguridad. Nunca apunte la boquilla en dirección de alguna persona al estar de cerca durante el uso de la sopladora. Siempre use la bolsa recolectora de polvo al estar recogiendo polvo, virutas y similares. No recoja cenizas de cigarrillos que estén aún ardiendo, así como virutas metálicas recientemente cortadas, tornillos, clavos y similares.
DESCRIPCIÓN DEL FUNCIONAMIENTO • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta. 008313 Para iniciar la herramienta, sólo tiene que jalar el gatillo interruptor. El volumen de aire aumenta al incrementar la presión en el gatillo interruptor. Suelte el gatillo interruptor para parar la herramienta.
Para el soplado de polvo, coloque la boquilla a la toma del soplador, girando en dirección de las agujas del reloj para fijar en su lugar. Para quitar la boquilla, gire en sentido contrario a las agujas del reloj. Limpieza Succión de polvo 1 2 1. Bolsa para polvo 2. Toma del soplador 3. Acceso de succión 4. Boquilla 012985 De vez en vez, limpie el exterior de la herramienta usando un paño húmedo y agua enjabonada. Nunca use gasolina, diluyente o algo similar que podría causar decoloración y/o grietas.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Combination Hammer Marteau combiné sans fil Martillo Rotativo Combinado Inalámbrico XRH04 009118 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XRH04 Concrete 24 mm (15/16") Steel 13 mm (1/2") Capacities Wood 26 mm (1") No load speed (RPM) 0 - 1,200 /min Blows per minute 0 - 4,000 Overall length 417 mm (16-3/8") Net weight 3.2 kg (7.1 lbs) Rated voltage 3.5 kg (7.7 lbs) D.C. 18 V Standard battery cartridges BL1815N / BL1820 BL1830 / BL1840 / BL1850 • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
9. 10. 11. 12. 13. 14. Hold the tool firmly with both hands. Keep hands away from moving parts. Do not leave the tool running. Operate the tool only when hand-held. Do not point the tool at any one in the area when operating. The bit could fly out and injure someone seriously. Do not touch the bit or parts close to the bit immediately after operation; they may be extremely hot and could burn your skin. Some material contains chemicals which may be toxic.
Lithium-ion batteries with a star marking are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: • Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the trigger switch on the tool and stop the application that caused the tool to become overloaded.
This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. For chipping, scaling or demolition operations, depress the lock button and rotate the action mode changing knob to the symbol. Use a bull point, cold chisel, scaling chisel, etc.
The bit can be secured at the desired angle. To change the bit angle, depress the lock button and rotate the action mode changing knob to the O symbol. Turn the bit to the desired angle. Depress the lock button and rotate the action mode changing knob to the symbol. Then make sure that the bit is securely held in place by turning it slightly. Installing or removing the bit Clean the bit shank and apply bit grease before installing the bit. 1. Bit shank 2.
Dust cup 5 Dust cup 9 After drilling the hole, use the blow-out bulb to clean the dust out of the hole. Bit diameter 6 mm (1/4") - 14.5 mm (9/16") 12 mm (15/32") - 16 mm (5/8") Chipping/Scaling/Demolition 006386 OPERATION Hammer drilling operation 009132 Set the action mode changing knob to the symbol. Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. There is a tremendous twisting force exerted on the tool/bit at the time of hole breakthrough. Hold the tool firmly and exert care when the bit begins to break through the workpiece. A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Capacités XRH04 Béton 24 mm (15/16") Acier 13 mm (1/2") Bois 26 mm (1") Vitesse à vide (T/MIN) 0 - 1 200 /min Nombre de frappes par minute 0 - 4 000 Longueur totale 417 mm (16-3/8") Poids net 3,2 kg (7,1 lbs) Tension nominale 3,5 kg (7,7 lbs) C.C.
19. Sécurité personnelle 10. Restez alerte, attentif à vos mouvements et faites preuve de bon sens lorsque vous utilisez un outil électrique. Évitez d'utiliser un outil électrique si vous êtes fatigué ou si vous avez pris une drogue, de l'alcool ou un médicament. Un moment d'inattention pendant l'utilisation d'un outil électrique peut entraîner une grave blessure. 11. Portez des dispositifs de protection personnelle. Portez toujours un protecteur pour la vue.
11. Réparation 28. Faites réparer votre outil électrique par un réparateur qualifié qui utilise des pièces de rechange identiques aux pièces d'origine. Le maintien de la sûreté de l'outil électrique sera ainsi assuré. 29. Suivez les instructions de lubrification et de changement des accessoires. 30. Maintenez les poignées de l'outil sèches, propres et exemptes d'huile ou de graisse. 12. 13. GEB046-2 14. CONSIGNES DE SÉCURITÉ POUR LE MARTEAU ROTATIF SANS FIL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
3. Cessez immédiatement l'utilisation si le temps de fonctionnement devient excessivement court. Il y a risque de surchauffe, de brûlures, voire d'explosion. 4. Si l'électrolyte pénètre dans vos yeux, rincez-les à l'eau claire et consultez immédiatement un médecin. Il y a risque de perte de la vue. 5. Ne court-circuitez pas la batterie : (1) Ne touchez les bornes avec aucun matériau conducteur.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) 1 Frein électrique Cet outil est équipé d'un frein électrique. Si à plusieurs reprises l'outil ne s'arrête pas rapidement après le relâchement de la gâchette, faites-le réparer dans un centre de service après-vente Makita. 1. Étoile Inverseur 1. Levier inverseur 1 A B 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection.
Rotation seulement ASSEMBLAGE 1. Rotation seulement • ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant d'effectuer tout travail dessus. Poignée latérale (poignée auxiliaire) 1 009123 1 5 1 Pour percer les matériaux de bois, de métal ou de plastique, appuyez sur le bouton de verrouillage et tournez le levier de changement de mode sur le symbole . Utilisez un foret hélicoïdal ou un foret à bois. Martelage seulement 2 4 3 1.
1 1. Embout 2. Couvercle du mandrin 2 009126 009129 S'il n'est pas possible d'enfoncer le foret, retirez-le. Tirez vers le bas le couvercle du mandrin à quelques reprises. Réinsérez ensuite le foret. Tournez le foret puis enfoncez-le jusqu'à ce qu'il soit engagé. Après l'installation, vérifiez toujours que le foret est solidement fixé en essayant de le sortir. Pour retirer le foret, tirez le couvercle du mandrin à fond vers le bas puis dégagez le foret. 1 Gabarit de profondeur 1. Embout 2.
UTILISATION Une fois le trou percé, utilisez la poire soufflante pour retirer la poussière du trou. Perçage avec martelage Burinage / Ecaillage / Démolition 009131 009132 Réglez le bouton de changement de mode sur le symbole . Posez la pointe du foret à l'emplacement du trou à percer et pressez sur la gâchette. Ne forcez pas sur l'outil. Une pression légère vous donnera les meilleurs résultats. Maintenez bien l'outil en position et veillez qu'il ne dérape pas hors du trou.
Une pression excessive sur l'outil n'accélère pas le perçage. Au contraire, elle risque d'endommager la pointe du foret, de réduire le rendement de l'outil et donc sa durée de service. Une force énorme s'exerce sur le foret et l'outil lorsque le foret émerge sur la face opposée. Tenez l'outil fermement et faites bien attention lorsque le foret commence à sortir de la face opposée de la pièce. Un foret coincé peut se retirer en plaçant l'inverseur sur la direction opposée.
NOTE: • Certains éléments de la liste peuvent être inclus avec l'outil comme accessoires standard. Ils peuvent varier suivant les pays. GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XRH04 Concreto 24 mm (15/16") Acero 13 mm (1/2") Capacidades Madera 26 mm (1") Velocidad sin carga (r.p.m.) 0 - 1 200 r/min Golpes por minuto 0 - 4 000 Longitud total 417 mm (16-3/8") Peso neto 3,2 kg (7,1 lbs) Tensión nominal 3,5 kg (7,7 lbs) 18 V c.c.
Seguridad personal 10. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice la herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera la máquina puede dar como resultado heridas personales graves. 11. Use equipo de protección personal. Póngase siempre protección para los ojos.
29. 30. 12. Siga las instrucciones para la lubricación y cambio de accesorios. Mantenga las agarraderas secas, limpias y sin aceite o grasa. 13. GEB046-2 ADVERTENCIAS DE SEGURIDAD PARA EL MARTILLO ROTATIVO INALÁMBRICO 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 14. Utilice protectores para oídos. La exposición al ruido puede causar la pérdida auditiva. Utilice el/los mango(s) auxiliar(es) si es que se incluye(n) en la herramienta. Una pérdida del control puede ocasionar lesiones personales.
4. En caso de que ingresen electrolitos en sus ojos, enjuáguelos bien con agua limpia y consulte de inmediato a un médico. Podría perder la visión. 5. No cortocircuite el cartucho de batería: (1) No toque las terminales con ningún material conductor. (2) Evite guardar el cartucho de batería en un cajón junto con otros objetos metálicos, tales como clavos, monedas, etc. (3) No exponga la batería de cartucho a la lluvia o nieve.
Para poner en marcha la herramienta, simplemente apriete el gatillo interruptor. La velocidad de la herramienta aumenta incrementando la presión en el gatillo. Suelte el gatillo interruptor para parar. Sistema de protección de batería (batería de ión de litio con marca de estrella) 1. Marca de estrella 1 Freno eléctrico Esta herramienta está equipada con un freno eléctrico.
Para taladrar concreto, mampostería, etc. pulse la traba y gire la perilla que cambia el modo de accionamento al símbolo . Utilice una broca de carburo de tungsteno. Acción de rotación solamente. ENSAMBLE • 1. Rotación solamente PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier trabajo en la misma.
1 1. Punta 2. Cubierta del mandril 2 009126 009129 Si la broca no puede ser empujada hacia dentro, extráigala. Tire de la cubierta del mandril hacia abajo unas cuantas veces. Después vuelva a insertar la broca. Gire la broca y presiónela hacia dentro hasta que quede encajada. Después de la instalación, asegúrese siempre de que esté bien sujeto en el mandril intentando sacarlo. Para retirar la broca/cincel, jale hacia abajo la cubierta del mandril y empuje la broca/cincel hacia el exterior.
OPERACIÓN Después de taladrar el agujero, utilice el soplador para limpiar el polvo del agujero. Operación de taladrado con percusión Cincelado/Tallado/Demolición 009131 009132 Ajuste la perilla que cambia el modo de accionamento al símbolo . Posicione la broca en el lugar deseado del orificio y luego accione el gatillo interruptor. No fuerce la herramienta. Con una presión menor, obtiene mejores resultados. Mantenga la herramienta en la posición adecuada y evite que se resbale del orificio.
Con ejercer una presión excesiva sobre la herramienta no conseguirá taladrar más rápido. De hecho, esta presión excesiva sólo servirá para dañar la punta de la broca, disminuir el rendimiento de la herramienta y acortar su vida de servicio. Se ejerce una tremenda fuerza de torsión en la broca/herramienta en el momento de pasar por el orificio. Sostenga firmemente la herramienta y tenga cuidado cuando la broca comience a romper la pieza de trabajo.
NOTA: • Algunos de los artículos en la lista puede que vengan junto con el paquete de la herramienta como accesorios incluidos. Puede que estos accesorios varíen de país a país. GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
31
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Recipro Saw Sierra Recíproca Inalámbrica XRJ04 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ04 Length of stroke 32 mm (1-1/4″) Strokes per minute Max. cutting capacities 0 - 2,800 /min Pipe 130 mm (5-1/8″) Wood 255 mm (10″) Rated voltage D.C. 18 V Standard battery cartridge BL1815N, BL1820, BL1820B Overall length 486 mm (19-1/8″) Net weight • • • BL1830, BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B 3.5 kg (7.6 lbs) 3.8 kg (8.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 2. 3. Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off.
Symbols CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. The followings show the symbols used for tool. volts direct current Tips for maintaining maximum battery life no load speed 1. revolutions or reciprocation per minute 2. Important safety instructions for battery cartridge 1. 2. 3.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. Indicating the remaining battery capacity To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
1 1 2 B A 2 ► 1 . Lock-off button 2. Switch trigger 3 ► 1 . Blade clamp lever 2. Released position 3. Fixed position To prevent the switch trigger from accidentally pulled, the lock-off button is provided. To start the tool, depress the lock-off button from B side and pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. After use, always press in the lock-off button from A side.
MAINTENANCE CAUTION: Keep hands and fingers away from the lever during the switching operation. Failure to do so may cause personal injuries. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position .
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ04 Extensión de la carrera 32 mm (1-1/4″) Carreras por minuto Capacidad máxima de corte 0 - 2 800 cpm Tubo 130 mm (5-1/8″) Madera 255 mm (10″) Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Use siempre gafas de seguridad o protectoras. Los anteojos comunes o para el sol NO son gafas de seguridad. Evite cortar clavos. Revise la pieza de trabajo y quite todos los clavos antes de utilizar la herramienta. No corte piezas de trabajo demasiado grandes. Compruebe que hay espacio suficiente más allá de la pieza de trabajo antes de cortar para que el disco no golpee el suelo, el banco de trabajo, etc. Sujete la herramienta con firmeza.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Si la herramienta no arranca, significa que la batería se sobrecalentó. En este caso, espere a que la batería se enfríe antes de volver a encender la herramienta.
Para instalar la segueta recíproca, asegúrese siempre de que la palanca de la abrazadera de la segueta (parte del manguito de la abrazadera de la segueta) esté en en la cubierta de aislamiento la posición liberada antes de insertar la segueta recíproca. Si la palanca de la abrazadera de la segueta se encuentra en la posición fija, gírela en la dirección de la flecha para que pueda ser trabada en la posición liberada . 2 1 1 ► 1 . Segueta recíproca 2.
1 ► 1 . Tapa del portaescobillas MANTENIMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. 3. Inserte el cartucho de batería en la herramienta y haga el rodaje de las escobillas poniendo a funcionar la herramienta sin carga durante 1 minuto aproximadamente. 4. Revise la herramienta mientras está funcionando y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA DE UN AÑO DE MAKITA Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de la fábrica. Se garantiza que está libre de defectos de mano de obra y materiales por el período de UN AÑO a partir de la fecha original de compra. Si durante este período de un año se desarrollara algún problema, devuelva la herramienta COMPLETA, con el envío prepagado, a un centro de servicio autorizado o de fábrica Makita.
17
18
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Angle Drill Perceuse d'Angle sans Fil Taladro Angular XAD01 014174 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XAD01 Steel Capacities 10 mm (3/8") Wood 25 mm (1") No load speed (RPM) 0 - 1,800 /min Overall length 314 mm (12-3/8") Net weight 1.5 kg (3.3 lbs) Rated voltage 1.8 kg (4.0 lbs) D.C. 18 V Standard battery cartridges BL1815N BL1830 / BL1840 • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from country to country.
27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Service 28. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 29. Follow instruction for lubricating and changing accessories. 30.
USD301-1 Tips for maintaining maximum battery life Symbols 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. Charge the battery cartridge with room temperature at 10 ゚ C - 40 ゚ C (50 ゚ F - 104 ゚ F). Let a hot battery cartridge cool down before charging it.
Battery protection system (Lithium-ion battery with star marking) Electric brake This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after switch trigger release, have tool serviced at a Makita service center. 1. Star marking 1 • CAUTION: Be sure to hold the tool firmly before the tool is switched off. Lighting up the front lamp 1. Lamp 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
• • • CAUTION: Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. Chuck key holder 1. Chuck key holder 2.
Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. • • • • • NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. CAUTION: Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XAD01 Acier Capacités 10 mm (3/8") Bois 25 mm (1") Vitesse à vide (T/MIN) 0 - 1 800 /min Longueur totale 314 mm (12-3/8") Poids net 1,5 kg (3,3 lbs) Tension nominale 1,8 kg (4,0 lbs) C.C. 18 V Batteries standard BL1815N BL1830 / BL1840 • Étant donné l'évolution constante de notre programme de recherche et de développement, les spécifications contenues dans ce manuel sont sujettes à modification sans préavis.
19. Débranchez la fiche de la source d'alimentation et/ou retirez le bloc-piles de l'outil électrique avant d'effectuer tout réglage, de changer un accessoire ou de ranger l'outil électrique. De telles mesures préventives réduisent les risques de démarrage accidentel de l'outil électrique. 20.
27. Dans des conditions d'utilisation inadéquates de la batterie, il peut y avoir fuite d'électrolyte; évitez tout contact avec ce liquide. En cas de contact accidentel, rincez avec beaucoup d’eau. Si le liquide pénètre dans vos yeux, il faut aussi consulter un médecin. L'électrolyte qui s'échappe de la batterie peut causer des irritations ou des brûlures. Réparation 28. Faites réparer votre outil électrique par un réparateur qualifié qui utilise des pièces de rechange identiques aux pièces d'origine.
7. 8. 9. Ne jetez pas la batterie au feu même si elle est sérieusement endommagée ou complètement épuisée. La batterie peut exploser au contact du feu. Prenez garde d'échapper ou de heurter la batterie. N'utilisez pas une batterie si elle est endommagée. DESCRIPTION DU FONCTIONNEMENT • CONSERVEZ CE MODE D'EMPLOI. ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. Installation ou retrait de la batterie 1.
L'outil s’arrête automatiquement pendant l'utilisation lorsque l'outil et/ou la batterie sont dans l’une des situations suivantes : • En surcharge : L'outil est utilisé d’une manière entraînant une consommation anormale de courant. Dans cette situation, relâchez la gâchette et arrêtez l'activité qui entraîne une surcharge de l'outil. Puis appuyez de nouveau sur la gâchette pour redémarrer. Si l’outil ne démarre pas, la batterie est en surchauffe.
Clavette de mandrin ASSEMBLAGE • 1. Clavette de mandrin 2. Vis ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant d'effectuer tout travail dessus. Installation de la poignée latérale (poignée auxiliaire) 1 2 014180 Pour installer la clavette de mandrin, fixez-la à la partie convexe du boîtier de l’outil (de chaque côté) et ensuite vissez-la solidement. Pour l’enlever, desserrez les vis et retirez-la. Crochet 1. Rainure 2. Crochet 3.
Perçage ACCESSOIRES EN OPTION Perçage du métal Pour empêcher le foret de glisser en début de perçage, faites une indentation au point de perçage à l'aide d'un poinçon et d'un marteau. Placez ensuite la pointe du foret dans l'indentation et commencez à percer. Quand vous forez dans du métal, utilisez un lubrifiant. Seuls le fer et le laiton peuvent se percer à sec.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XAD01 Acero Capacidades 10 mm (3/8") Madera 25 mm (1") Velocidad sin carga (r.p.m.) 0 - 1 800 r/min Longitud total 314 mm (12-3/8") Peso neto 1,5 kg (3,3 lbs) Tensión nominal 1,8 kg (4,0 lbs) 18 V c.c. Cartuchos de batería estándar BL1815N BL1830 / BL1840 • Debido a nuestro programa continuo de investigación y desarrollo, las especificaciones aquí dadas están sujetas a cambios sin previo aviso.
19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20. Guarde la herramienta eléctrica que no use fuera del alcance de los niños y no permita que las personas que no están familiarizadas con ella o con las instrucciones la operen.
27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. Servicio de mantenimiento 28. Haga que una persona calificada repare la herramienta utilizando sólo piezas de repuesto idénticas. Esto asegura que se mantenga la seguridad de la herramienta eléctrica. 29.
7. 8. 9. Nunca incinere el cartucho de batería incluso en el caso de que esté dañado seriamente o ya no sirva en absoluto. El cartucho de batería puede explotar si se tira al fuego. Tenga cuidado de no dejar caer ni golpear el cartucho de batería. No use una batería dañada. DESCRIPCIÓN DEL FUNCIONAMIENTO • GUARDE ESTAS INSTRUCCIONES. Instalación o desmontaje del cartucho de batería Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4.
Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección. Este sistema corta en forma automática el suministro de energía a la herramienta para prolongar la vida útil de la batería. La herramienta se detendrá automáticamente durante el funcionamiento si la herramienta y/o la batería se someten a una de las siguientes condiciones: • Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta.
Cuando no esté utilizando la herramienta, ponga siempre la palanca del conmutador de inversión en la posición neutral. • Sujetador de llave de portabroca 1. Sujetador de llave de portabroca 2. Tornillo ENSAMBLE • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier trabajo en la misma.
Operación de taladrado ACCESORIOS OPCIONALES Taladrado en metal Para evitar que la broca resbale al empezar a hacer el agujero, haga una mella con punzón y un martillo en el punto a taladrar. Coloque la punta de la broca en la mella y comience a taladrar. Emplee un lubricante para operaciones de corte cuando taladre metales. Las excepciones son hierro y latón que deberán ser taladrados en seco.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Impact Wrench Boulonneuse sans Fil Llave de Impacto Inalámbrica XWT05 007450 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities XWT05 Standard bolt M10 - M16 (3/8" - 5/8" ) High tensile bolt M10 - M14 (3/8" - 9/16" ) Square drive 12.7 mm (1/2") No load speed (RPM) 0 - 2,100 /min Impacts per minute 0 - 3,200 Max. fastening torque 230 N·m (2,040 in.lbs) Overall length 165 mm (6-1/2") Net weight 1.5 kg (3.3 lbs) Rated voltage 1.7 kg (3.8 lbs) D.C.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
7. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 8. 9. SAVE THESE INSTRUCTIONS. USD302-1 Tips for maintaining maximum battery life 1. Symbols The followings show the symbols used for tool.
• Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the trigger switch on the tool and stop the application that caused the tool to become overloaded. Then pull the trigger switch again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the trigger switch again. Low battery voltage: The remaining battery capacity is too low and the tool will not operate.
CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The light automatically goes out 10 - 15 seconds after the switch trigger is released. Installing or removing socket • 3 4 1. Socket 2. Hole 3. Anvil 4. Detent pin 1 2 3 4 NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.
The proper fastening torque may differ depending upon the kind or size of the bolt, the material of the workpiece to be fastened, etc. The relation between fastening torque and fastening time is shown in the figures. 1. When the battery cartridge is discharged almost completely, voltage will drop and the fastening torque will be reduced. Socket • Failure to use the correct size socket will cause a reduction in the fastening torque.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1. Rear cover 2. Screws 1 2 OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Capacités XWT05 Boulon standard M10 - M16 (3/8" - 5/8" ) Boulon à haute résistance M10 - M14 (3/8" - 9/16" ) Tournevis carré 12,7 mm (1/2") Vitesse à vide (T/MIN) 0 - 2 100 /min Percussions par minute 0 - 3 200 Couple de serrage max. 230 N·m (2 040 in.lbs) Longueur totale 165 mm (6-1/2") Poids net 1,5 kg (3,3 lbs) Tension nominale 1,7 kg (3,8 lbs) C.C.
l'interrupteur est défectueux représente un danger et doit être réparé. 19. Débranchez la fiche de la source d'alimentation et/ou retirez le bloc-piles de l'outil électrique avant d'effectuer tout réglage, de changer un accessoire ou de ranger l'outil électrique. De telles mesures préventives réduisent les risques de démarrage accidentel de l'outil électrique. 20.
27. Dans des conditions d'utilisation inadéquates de la batterie, il peut y avoir fuite d'électrolyte; évitez tout contact avec ce liquide. En cas de contact accidentel, rincez avec beaucoup d’eau. Si le liquide pénètre dans vos yeux, il faut aussi consulter un médecin. L'électrolyte qui s'échappe de la batterie peut causer des irritations ou des brûlures. Réparation 28. Faites réparer votre outil électrique par un réparateur qualifié qui utilise des pièces de rechange identiques aux pièces d'origine.
7. 8. 9. Ne jetez pas la batterie au feu même si elle est sérieusement endommagée ou complètement épuisée. La batterie peut exploser au contact du feu. Prenez garde d'échapper ou de heurter la batterie. N'utilisez pas une batterie si elle est endommagée. DESCRIPTION DU FONCTIONNEMENT • CONSERVEZ CE MODE D'EMPLOI. Installation ou retrait de la batterie Conseils pour obtenir la durée de service maximale de la batterie 1. 2. 3. 4.
L'outil s’arrête automatiquement pendant l'utilisation lorsque l'outil et/ou la batterie sont dans l’une des situations suivantes : • En surcharge : L'outil est utilisé d’une manière entraînant une consommation anormale de courant. Dans cette situation, relâchez la gâchette et arrêtez l'activité qui entraîne une surcharge de l'outil. Puis appuyez de nouveau sur la gâchette pour redémarrer. Si l’outil ne démarre pas, la batterie est en surchauffe.
Installation et retrait de la douille 3 4 1 2 3 4 1. Douille 2. Orifice 3. Enclume 4. Broche de détente 007461 Le couple de serrage adéquat peut varier suivant la sorte ou taille de boulon, suivant le matériau dont se compose la pièce faisant l'objet du serrage, etc. La relation entre le couple de serrage et le temps de serrage est indiquée dans les figures.
Avant de commencer le travail, effectuez toujours un essai pour vérifier que le temps de serrage conviennent pour le boulon ou l'écrou en question. • Si vous utilisez l'outil en continu jusqu'à ce que la batterie soit à plat, attendez 15 minutes avant d'insérer une autre batterie. Le couple de serrage dépend d'un certain nombre de facteurs, comme suit. Une fois le serrage terminé, vérifiez toujours le couple avec une clé dynamométrique. 1.
Assurez-vous que les bouchons sont bien introduits dans les orifices des charbons. 1 GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo Capacidades XWT05 Tornillo estándar M10 - M16 (3/8" - 5/8" ) Tornillo de alta tracción M10 - M14 (3/8" - 9/16" ) Adaptador cuadrado 12,7 mm (1/2") Velocidad sin carga (r.p.m.) 0 - 2 100 r/min Impactos por minuto 0 - 3 200 Torsión de fijación máxima 230 N·m (2 040 in.lbs) Longitud total 165 mm (6-1/2") Peso neto 1,5 kg (3,3 lbs) Tensión nominal 1,7 kg (3,8 lbs) 18 V c.c.
18. No utilice la herramienta eléctrica si el interruptor no la enciende y apaga. Cualquier herramienta eléctrica que no pueda ser controlada con el interruptor es peligrosa y debe ser reemplazada. 19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20.
26. Cuando no se esté usando el cartucho de la batería, manténgalo alejado de otros objetos metálicos, como sujetapapeles (clips), monedas, llaves, clavos, tornillos u otros objetos pequeños de metal los cuales pueden actuar creando una conexión entre las terminales de la batería. Cerrar el circuito las terminales de la batería puede causar quemaduras o incendios. 27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua.
6. 7. 8. 9. No guarde la herramienta ni el cartucho de batería en lugares donde la temperatura pueda alcanzar o exceder los 50 ゚ C (122 ゚ F). Nunca incinere el cartucho de batería incluso en el caso de que esté dañado seriamente o ya no sirva en absoluto. El cartucho de batería puede explotar si se tira al fuego. Tenga cuidado de no dejar caer ni golpear el cartucho de batería. No use una batería dañada.
Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección. Este sistema corta en forma automática el suministro de energía a la herramienta para prolongar la vida útil de la batería. La herramienta se detendrá automáticamente durante el funcionamiento si la herramienta y/o la batería se someten a una de las siguientes condiciones: • Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta.
OPERACIÓN ENSAMBLE • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier trabajo en la misma. PRECAUCIÓN: Inserte siempre el cartucho de la batería a tope hasta que se bloquee en su sitio. Si puede ver la parte roja del lado superior del botón, no estará bloqueado completamente. Insértelo completamente hasta que no pueda verse la parte roja.
4. La utilización de una junta universal o de una barra de extensión reduce de alguna manera la fuerza de apriete de la llave de impacto. Compense esto alargando el tiempo de apriete. La forma de sostener la herramienta o el material en la posición a apretar afectará a la torsión. La operación de la herramienta a baja velocidad ocasionará una reducción de la torsión de apriete.
ACCESORIOS OPCIONALES 1. Resorte 2. Brazo 3. Parte rebajada 1 PRECAUCIÓN: Estos accesorios o aditamentos (incluidos o no) están recomendados para utilizar con su herramienta Makita especificada en este manual. El empleo de cualesquiera otros accesorios o acoplamientos conllevará un riesgo de sufrir heridas personales. Utilice los accesorios o acoplamientos solamente para su fin establecido.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
27
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Impact Wrench Boulonneuse sans Fil Llave de Impacto Inalámbrica XWT04 008145 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities XWT04 Standard bolt M12 - M22 (1/2 " - 7/8") High tensile bolt M12 - M16 (1/2" - 5/8") Square drive 12.7 mm (1/2") No load speed (RPM) 1,600 /min Impacts per minute 2,200 Max. fastening torque 440 N·m (3,900 in.lbs) Overall length 266 mm (10-1/2") Net weight 3.1 kg (6.8 lbs) Rated voltage 3.4 kg (7.5 lbs) D.C.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
7. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 8. 9. SAVE THESE INSTRUCTIONS. USD302-1 Tips for maintaining maximum battery life 1. Symbols The followings show the symbols used for tool.
The switch is reversible, providing either clockwise or counterclockwise rotation. To start the tool, simply pull the lower part (A) of the switch trigger for clockwise or the upper part (B) for counterclockwise. Release the switch trigger to stop. FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Lighting up the front lamp Installing or removing battery cartridge 2 1. Red part 2.
Installing or removing socket OPERATION For tool with light fit detent pin 3 4 1. Socket 2. Hole 3. Anvil 4. Detent pin 1 2 CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Hold the tool firmly and place the socket over the bolt or nut.
4. Nm (ft lbs) The use of the universal joint or the extension bar somewhat reduces the fastening force of the impact wrench. Compensate by fastening for a longer period of time. The manner of holding the tool or the material of driving position to be fastened will affect the torque. Operating the tool at low speed will cause a reduction in the fastening torque.
OPTIONAL ACCESSORIES MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Capacités XWT04 Boulon standard M12 - M22 (1/2 " - 7/8") Boulon à haute résistance M12 - M16 (1/2" - 5/8") Tournevis carré 12,7 mm (1/2") Vitesse à vide (T/MIN) 1 600 /min Percussions par minute 2 200 Couple de serrage max. 440 N·m (3 900 in.lbs) Longueur totale 266 mm (10-1/2") Poids net 3,1 kg (6,8 lbs) Tension nominale 3,4 kg (7,5 lbs) C.C.
18. N'utilisez pas l'outil électrique s'il n'est pas possible de mettre sa gâchette en position de marche et d'arrêt. Un outil électrique dont l'interrupteur est défectueux représente un danger et doit être réparé. 19. Débranchez la fiche de la source d'alimentation et/ou retirez le bloc-piles de l'outil électrique avant d'effectuer tout réglage, de changer un accessoire ou de ranger l'outil électrique. De telles mesures préventives réduisent les risques de démarrage accidentel de l'outil électrique. 20.
USD302-1 27. Dans des conditions d'utilisation inadéquates de la batterie, il peut y avoir fuite d'électrolyte; évitez tout contact avec ce liquide. En cas de contact accidentel, rincez avec beaucoup d’eau. Si le liquide pénètre dans vos yeux, il faut aussi consulter un médecin. L'électrolyte qui s'échappe de la batterie peut causer des irritations ou des brûlures. Réparation 28.
9. N'utilisez pas endommagée. une batterie si elle est DESCRIPTION DU FONCTIONNEMENT CONSERVEZ CE MODE D'EMPLOI. • Conseils pour obtenir la durée de service maximale de la batterie 1. 2. 3. Rechargez la batterie avant qu'elle ne soit complètement déchargée. Arrêtez toujours l'outil et rechargez la batterie quand vous remarquez que la puissance de l'outil diminue. Ne rechargez jamais une batterie complètement chargée. La surcharge réduit la durée de service de la batterie.
ATTENTION: Avant d'insérer la batterie dans l'outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d'arrêt lorsque relâchée. • Attendez que l'outil soit complètement arrêté avant de changer le sens de rotation. Vous risquez d'endommager l'outil si vous changez le sens de rotation avant que l'outil ne soit complètement arrêté. La gâchette est réversible, permettant ainsi de faire tourner l'outil dans le sens des aiguilles d'une montre ou en sens inverse.
Boulon standard Nm (ft lbs) Couple de serrage 3 008150 L'outil est équipé d'un crochet pratique qui permet de le suspendre temporairement. Il s'installe d'un côté comme de l'autre de l'outil. Pour installer le crochet, insérez-le dans les rainures situées de chaque côté du carter de l'outil, puis serrez-le avec une vis. Pour le retirer, desserrez la vis et enlevez-la.
Si vous utilisez l'outil en continu jusqu'à ce que la batterie soit à plat, attendez 15 minutes avant d'insérer une autre batterie. Le couple de serrage dépend d'un certain nombre de facteurs, comme suit. Une fois le serrage terminé, vérifiez toujours le couple avec une clé dynamométrique. 1. Lorsque la batterie est presque complètement déchargée, la tension tombe et le couple de serrage diminue. 2. Douille • L'utilisation d'une douille de mauvaise dimension entraînera une réduction du couple de serrage.
ACCESSOIRES EN OPTION GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo Capacidades XWT04 Tornillo estándar M12 (1/2” - 12,7 mm) - M22 (7/8” - 22 mm) Tornillo de alta tracción M12 (1/2” - 12,7 mm) - M16 (5/8” - 15,8 mm) Adaptador cuadrado 12,7 mm (1/2") Velocidad sin carga (r.p.m.) 1 600 r/min Impactos por minuto 2 200 Torsión de fijación máxima 440 N·m (3 900 in.lbs) Longitud total 266 mm (10-1/2") Peso neto 3,1 kg (6,8 lbs) Tensión nominal 3,4 kg (7,5 lbs) 18 V c.c.
18. No utilice la herramienta eléctrica si el interruptor no la enciende y apaga. Cualquier herramienta eléctrica que no pueda ser controlada con el interruptor es peligrosa y debe ser reemplazada. 19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20.
monedas, llaves, clavos, tornillos u otros objetos pequeños de metal los cuales pueden actuar creando una conexión entre las terminales de la batería. Cerrar el circuito las terminales de la batería puede causar quemaduras o incendios. 27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras.
6. 7. 8. 9. No guarde la herramienta ni el cartucho de batería en lugares donde la temperatura pueda alcanzar o exceder los 50 ゚ C (122 ゚ F). Nunca incinere el cartucho de batería incluso en el caso de que esté dañado seriamente o ya no sirva en absoluto. El cartucho de batería puede explotar si se tira al fuego. Tenga cuidado de no dejar caer ni golpear el cartucho de batería. No use una batería dañada.
PRECAUCIÓN: Antes de insertar el cartucho de batería en la herramienta, compruebe siempre y cerciórese de que el gatillo interruptor se acciona debidamente y que vuelve a la posición "OFF"(apagado) cuando lo suelta. • Cambie la dirección de giro solamente después de que la herramienta haya parado completamente. Si lo cambia antes, la herramienta se puede averiar. El interruptor es reversible y provee una rotación bien a la derecha o bien a la izquierda.
Perno o Tornillo estándar 3 008150 El gancho resulta útil para colgar temporalmente la herramienta. Se puede instalar en cualquiera de los lados de la herramienta. Para instalar el gancho, insértelo en una ranura del alojamiento de la herramienta de cualquiera de los lados y después sujételo con un tornillo. Para quitarlo, afloje el tornillo y después sáquelo.
perno o la tuerca que quiere apretar. Si se opera la herramienta de forma continua hasta que se agote la batería, permita unos 15 minutos de descanso de la herramienta antes de cambiar y continuar con un cartucho de batería recargado. La torsión de apriete se ve afectada por una amplia variedad de factores incluyendo los siguientes. Después del apriete, compruebe siempre la torsión de apriete con una llave de torsión. 1.
ACCESORIOS OPCIONALES GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México PRECAUCIÓN: Estos accesorios o aditamentos (incluidos o no) están recomendados para utilizar con su herramienta Makita especificada en este manual. El empleo de cualesquiera otros accesorios o acoplamientos conllevará un riesgo de sufrir heridas personales. Utilice los accesorios o acoplamientos solamente para su fin establecido.
25
26
27
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Circular Saw Scie Circulaire sans Fil Sierra Circular Inalámbrica XSS01 XSS02 006699 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XSS01 Blade diameter Max. Cutting depth XSS02 165 mm (6-1/2") at 90° 57 mm (2-1/4") at 45° 40 mm (1-9/16") at 50° 36 mm (1-7/16") No load speed (RPM) 3,700 /min Overall length 347 mm (13-5/8") Net weight 3.2 kg (7.1 lbs) Rated voltage 3.5 kg (7.6 lbs) 3.1 kg (6.8 lbs) 3.3 kg (7.3 lbs) D.C.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
12. 5. Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and could give the operator an electric shock. 6. When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding. 7. Always use blades with correct size and shape (diamond versus round) of arbour holes.
Additional safety warnings 23. Intended use This tool is intended to cut wood products only. Accumulated sawdust on the lower guard and hub from other materials may effect the proper closure of the lower guard which could lead to serious personal injury. 24. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing knots. Maintain smooth advancement of tool without decrease in blade speed to avoid overheating the blade tips. 25.
ENC007-8 IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4.
Battery protection system (Lithium-ion battery with star marking) FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1. Star marking 1 Installing or removing battery cartridge 1 2 1. Red indicator 2. Button 3. Battery cartridge 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
Bevel cutting Switch action 1. Lever 1 2 1. Switch trigger 2. Lock-off lever 1 006702 006705 For Model XSS01 CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. • Do not pull the switch trigger hard without pressing the lock-off lever. This can cause switch breakage. To prevent the switch trigger from being accidentally pulled, a lock-off lever is provided.
NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. • Do not use gasoline, thinner or the like to clean the lens of lamp. Using such substances will damage the lens. Hex wrench storage 1. Hex wrench 1 ASSEMBLY • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
• If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. 1 2 MAINTENANCE 1. Rear handle 2. Front grip 3. Base • • 3 006709 Hold the tool firmly. The tool is provided with both a front grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by the blade. Set the base on the workpiece to be cut without the blade making any contact.
Replacing carbon brushes Combination 1. Limit mark General purpose blade for fast and smooth rip, crosscuts and miters. 006540 • • • • Rip fence (Guide rule) Hex wrench 5 Dust nozzle Makita genuine battery and charger 1 NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. 001145 Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XSS01 Diamètre de la lame Profondeur de coupe max. XSS02 165 mm (6-1/2") à 90° 57 mm (2-1/4") à 45° 40 mm (1-9/16") à 50° 36 mm (1-7/16") Vitesse à vide (T/MIN) 3 700 /min Longueur totale 347 mm (13-5/8") Poids net 3,2 kg (7,1 lbs) Tension nominale 3,5 kg (7,6 lbs) 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) C.C.
Sécurité personnelle 10. Restez alerte, attentif à vos mouvements et faites preuve de bon sens lorsque vous utilisez un outil électrique. Évitez d'utiliser un outil électrique si vous êtes fatigué ou si vous avez pris une drogue, de l'alcool ou un médicament. Un moment d'inattention pendant l'utilisation d'un outil électrique peut entraîner une grave blessure. 11. Portez des dispositifs de protection personnelle. Portez toujours un protecteur pour la vue.
contact avec un conducteur sous tension, les pièces métalliques à découvert de l'outil deviendraient également sous tension et risqueraient de transmettre une décharge à l'utilisateur. 6. Lors du sciage en long, utilisez toujours un garde parallèle ou un guide de coupe rectiligne. Cela améliore la précision de la coupe et réduit le risque de coincement de la lame. 7. Employez toujours une lame de diamètre approprié et dont le trou central est de forme correcte (angulaire ou ronde).
15. la cause du coincement de la lame et prenez les mesures correctives pour éliminer le problème. 11. Avant de faire redémarrer la scie dans la pièce, centrez la lame dans le trait de scie et assurez-vous que les dents de la lame ne mordent pas déjà dans le matériau. Si la lame est coincée, elle risque de remonter dans le trait de scie ou de causer un recul au moment du redémarrage de la scie. 12.
rappel et libérez le protecteur inférieur dès que la lame pénètre dans le matériau. Pour toute autre opération de sciage, le protecteur inférieur devrait fonctionner automatiquement. 21. Assurez-vous toujours que le protecteur inférieur couvre bien la lame avant de déposer l'outil sur l'établi ou sur le sol. Si la lame n'est pas protégée et n'a pas fini de tourner, elle entraînera la scie vers l'arrière en coupant tout sur son passage.
31. 32. 33. 34. 35. N'appliquez jamais une pression latérale sur la lame pour l'arrêter. N'utilisez aucune meule abrasive. N'utilisez que la lame dont le diamètre correspond aux indications données sur l’outil ou dans le manuel. L’utilisation d’une lame d’une taille incorrecte peut affecter la protection de la lame ou le fonctionnement du protecteur et cela pourrait causer de graves blessures. Maintenez la lame affûtée et propre.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) DESCRIPTION DU FONCTIONNEMENT 1. Étoile 1 • ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. Installation ou retrait de la batterie 1 2 1. Indicateur rouge 2. Bouton 3. Batterie 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection.
d'une dent de lame ne dépasse sous la pièce. L'utilisation d'une profondeur de coupe adéquate aide à réduire les risques de chocs en retour dangereux qui peuvent causer des blessures. Interrupteur 1 Coupe en biseau 2 1. Gâchette 2. Levier de sécurité 1. Levier 006705 ATTENTION: Avant d'insérer la batterie dans l'outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d'arrêt lorsque relâchée.
Pour allumer la lumière sans faire démarrer l'outil, appuyez sur la gâchette sans appuyer sur le levier de déverrouillage. Pour allumer la lumière et faire démarrer l'outil, appuyez sur le levier de déverrouillage et appuyez sur la gâchette alors que le levier de verrouillage est enfoncé. 2 3 NOTE: • Utilisez un chiffon sec pour essuyer la saleté qui recouvre la lentille de la lampe. Prenez garde de rayer la lentille de la lampe, pour éviter une diminution de l'éclairage.
Garde parallèle (règle de guidage) UTILISATION • • • 1. Vis de serrage 2. Garde parallèle (règle de guidage) ATTENTION: Insérez toujours la batterie jusqu'au fond, jusqu'à ce qu'elle verrouille en place. Si vous pouvez voir la partie rouge de la face supérieure du bouton, la batterie n'est pas parfaitement verrouillée. Insérez-la à fond, jusqu'à ce que la partie rouge ne soit plus visible.
demande de réparation auprès du centre de service après-vente Makita le plus près. Réglage de précision pour la coupe à 90° (coupe verticale) Pour le modèle XSS02 Ce réglage est réalisé en usine. S'il se défait, ajustez la vis de réglage au moyen d'une clé hexagonale tout en mesurant l'angle de 90° de la lame par rapport à la base à l'aide d'une règle triangulaire, d'une équerre, etc. 2 1 1 2 1. Réglage de la vis à 45 ゚ (XSS01 seulement) 2.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XSS01 Diámetro del disco Profundidad de corte máxima XSS02 165 mm (6-1/2") a 90° 57 mm (2-1/4") a 45° 40 mm (1-9/16") a 50° 36 mm (1-7/16") Velocidad sin carga (r.p.m.) 3 700 r/min Longitud total 347 mm (13-5/8") Peso neto 3,2 kg (7,1 lbs) 3,5 kg (7,6 lbs) Tensión nominal 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) 18 V c.c.
19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20. Guarde la herramienta eléctrica que no use fuera del alcance de los niños y no permita que las personas que no están familiarizadas con ella o con las instrucciones la operen.
27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. Servicio de mantenimiento 28. Haga que una persona calificada repare la herramienta utilizando sólo piezas de repuesto idénticas. Esto asegura que se mantenga la seguridad de la herramienta eléctrica. 29.
11. 12. inmóvil en el material hasta que el disco se pare completamente. No intente nunca extraer el disco de la pieza de trabajo ni tirar de la sierra hacia atrás mientras el disco esté moviéndose porque podrá ocasionar un retroceso brusco. Investigue y tome medidas correctivas para eliminar la causa del atoramiento del disco. Cuando vuelva a poner en marcha la sierra sobre la pieza de trabajo, centre la sierra en la entalladura y compruebe que sus dientes no estén en contacto con el material.
especiales como “cortes de cavidad” y “cortes compuestos.” Levante el protector inferior mediante el mango retráctil y cuando el disco entre en el material, debe soltar el protector inferior. Para todos los otros cortes con sierra, el protector inferior debe funcionar automáticamente. 21. Antes de dejar la sierra en el banco o en el suelo, observe siempre que el protector inferior esté cubriendo el disco.
31. 32. 33. 34. 35. No detenga el disco de la sierra mediante presión lateral sobre el mismo. No use ningún disco abrasivo. Use solamente un disco de sierra cuyo diámetro esté marcado en la herramienta o especificado en el manual. El uso de un disco de sierra de tamaño inadecuado puede que afecte la protección del disco o del protector en sí, lo cual podría resultar en graves lesiones al operador. Mantenga el disco afilado y limpio.
Sistema de protección de batería (batería de ión de litio con marca de estrella) DESCRIPCIÓN DEL FUNCIONAMIENTO 1. Marca de estrella 1 • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Instalación o desmontaje del cartucho de batería 1 2 012128 Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección.
Afloje la palanca del lateral del mango posterior y mueva la base hacia arriba o hacia abajo. Cuando haya alcanzado la profundidad de corte deseada, fije la base apretando la palanca. Para obtener cortes más limpios y seguros, ajuste la profundidad de corte de forma que no sobresalga más de un diente del disco de sierra por debajo de la pieza de trabajo.
Utilice solamente la llave Makita para instalar o desmontar el disco. Para quitar el disco, presione el bloqueo del eje de forma que el disco no pueda girar y afloje el perno hexagonal girándolo en sentido de las agujas del reloj con la llave. Después quite el perno hexagonal, la brida exterior y el disco. Para instalar el disco, siga el procedimiento de desmontaje a la inversa. ASEGÚRESE DE APRETAR EL PERNO HEXAGONAL EN SENTIDO CONTRARIO A LAS AGUJAS DEL RELOJ FIRMEMENTE.
velocidad. Ahora simplemente mueva la herramienta hacia delante sobre la superficie de la pieza de trabajo, manteniéndola plana y avanzando suavemente hasta completar el corte. Para obtener cortes limpios, mantenga la línea de corte recta y la velocidad de avance uniforme. Si se desvía de la línea de corte prevista, no intente girar ni forzar la herramienta para hacerla volver a la línea de corte. Esta acción podría inmovilizar el disco y ocasionar un peligroso retroceso brusco y posibles heridas graves.
Utilice un destornillador para quitar las tapas de los portaescobillas. Extraiga las escobillas gastadas, inserte las nuevas y vuelva a colocar las tapas. Para modelo XSS01 Después de reemplazar las escobillas, inserte el cartucho de batería en la herramienta y hágale el rodaje a las escobillas haciendo funcionar la herramienta sin carga durante 1 minuto aproximadamente. Después compruebe la herramienta mientras está en marcha y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Hammer Driver Drill Perceuse Percussion-Visseuse sans Fil Rotomartillo Atornillador Inalámbrico XPH10 Read Before Using. IMPORTANT : Lire avant usage. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Drilling capacities Fastening capacities XPH10 Concrete 13 mm (1/2") Steel 13 mm (1/2") Wood 38 mm (1-1/2") Wood screw 10 mm x 90 mm (3/8" x 3-1/2") Machine screw No load speed (RPM) Blows per minute M6 (1/4") High (2) 0 - 1,900 /min Low (1) 0 - 600 /min High (2) 0 - 28,500 /min Low (1) 0 - 9,000 /min Overall length 198 mm (7-3/4") Rated voltage Standard battery cartridge D.C.
4. 5. 6. 7. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Symbols The followings show the symbols used for tool. Tips for maintaining maximum battery life 1. volts direct current no load speed 2. 3. revolutions or reciprocation per minute number of blow Important safety instructions for battery cartridge 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge.
CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. CAUTION: Do not install the battery cartridge Indicating the remaining battery capacity Only for battery cartridges with "B" at the end of the model number forcibly. If the cartridge does not slide in easily, it is not being inserted correctly. Battery protection system 1 Lithium-ion battery with star marking 1 2 1.
Switch action Reversing switch action A B 1 1 1. Switch trigger CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Electric brake This tool is equipped with an electric brake.
Position of speed change lever Speed Torque Applicable operation 1 Low High Heavy loading operation 2 High Low Light loading operation 2 To change the speed, switch off the tool first. Select the "2" side for high speed or "1" for low speed but high torque. Be sure that the speed change lever is set to the correct position before operation. If the tool speed is coming down extremely during the operation with "2", slide the lever to the "1" and restart the operation. 3 1 4 1.
Installing driver bit holder ASSEMBLY CAUTION: Always be sure that the tool is Optional accessory switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ drill bit 1 Optional accessory 2 1 3 1. Driver bit holder 2. Driver bit 2 Fit the driver bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the driver bit holders.
Screwdriving operation Drilling operation CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. First, turn the action mode changing ring so that the arrow on the tool body points to the marking. Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually.
Replacing carbon brushes 1 1 1. Carbon brush cap 4. Make sure to place the lead wire in opposite side of the arm. 1. Limit mark Check the carbon brushes regularly. Replace them when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. 2 1. Use a screwdriver to remove two screws then remove the rear cover. 1 1 1. Lead wire 2. Carbon brush cap 5.
OPTIONAL ACCESSORIES Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle : Capacité de perçage Capacité de serrage XPH10 Béton 13 mm (1/2") Acier 13 mm (1/2") Bois 38 mm (1-1/2") Vis à bois 10 mm x 90 mm (3/8" x 3-1/2") Vis de mécanique Vitesse à vide (RPM) Nombre de frappes par minute M6 (1/4") Max. (2) 0 - 1 900 /min Min. (1) 0 - 600 /min Max. (2) 0 - 28 500 /min Min. (1) 0 - 9 000 /min Longueur totale 198 mm (7-3/4") Tension nominale Batterie standard Poids net • • • C.C.
Sécurité personnelle 1. Restez alerte, attentif à vos mouvements et faites preuve de bon sens lorsque vous utilisez un outil électrique. N’utilisez pas les outils électriques si vous êtes fatigué ou avez pris une drogue, de l’alcool ou un médicament. Un moment d’inattention pendant l’utilisation d’un outil électrique peut entraîner une grave blessure. 2. Portez des dispositifs de protection personnelle. Portez toujours une protection oculaire.
Consignes de sécurité pour perceuse percussion-visseuse sans fil 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Portez des protections d’oreilles lorsque vous utilisez une perceuse à percussion. L’exposition au bruit peut entraîner des lésions de l’ouïe. Utilisez la ou les poignées auxiliaires si elles sont fournies avec l’outil. Toute perte de maîtrise comporte un risque de blessure.
CONSERVEZ CES INSTRUCTIONS. Pour retirer la batterie, faites-la glisser hors de l’outil tout en glissant le bouton qui se trouve à l’avant. ATTENTION : Utilisez exclusivement les bat- teries fabriquées par Makita. Les batteries autres que celles fabriquées par Makita ou les batteries modifiées peuvent exploser et causer un incendie, une blessure ou des dommages. Cela annule aussi la garantie Makita de l’outil et du chargeur Makita. Conseils pour maintenir la durée de service maximale de la batterie 1.
Affichage de la charge restante de la batterie Interrupteur Uniquement pour les batteries dont le numéro de modèle se termine par « B » 1 1 2 1. Gâchette 1. Témoins indicateurs 2. Bouton de vérification Appuyez sur le bouton de vérification de la batterie pour afficher la charge restante de la batterie. Les témoins indicateurs s’allument pendant quelques secondes.
Fonctionnement de l’inverseur A B 1 1. Levier inverseur Position du levier de changement de vitesse Vitesse Couple de serrage Type de travail 1 Réduite Élevée Charge de travail lourde 2 Élevé Réduit Charge de travail légère Pour modifier la vitesse, éteignez d’abord l’outil. Sélectionnez « 2 » pour une vitesse élevée, ou « 1 » pour une vitesse réduite avec un couple de serrage élevé.
Réglage du couple de serrage 2 3 1 4 1. Bague de changement de mode 2. Bague de réglage 3. Graduation 4. Flèche Le couple de serrage peut être réglé sur un des 21 niveaux en tournant la bague de réglage. Alignez les graduations avec la flèche sur le bâti de l’outil. Le couple de serrage est au minimum lorsqu’il est à 1 et au maximum lorsqu’il est à 21.
insérez-le dans l’une ou l’autre des rainures situées de chaque côté du boîtier de l’outil, puis serrez-le avec une vis. Pour le retirer, desserrez la vis et enlevez-la. Installation du support d’embout-tournevis Accessoire en option 1 Vissage 2 1. Support d’embout-tournevis 2. Embout-tournevis Placez le support d’embout-tournevis dans la partie saillante au pied de l’outil, du côté droit ou gauche, et fixez-le à l’aide d’une vis.
Poire soufflante ATTENTION : Une pression excessive sur l’outil n’accélère pas le perçage. Au contraire, elle risque d’endommager la pointe de l’embout-foret, d’affecter le rendement de l’outil et de raccourcir sa durée de service. Accessoire en option 1 1. Poire soufflante Une fois le trou percé, utilisez la poire soufflante pour retirer la poussière du trou. Perçage Tournez d’abord la bague de réglage de sorte que le curseur pointe sur l’indication . Procédez ensuite comme suit.
N’utilisez que des charbons identiques. 1. Retirez les deux vis à l’aide d’un tournevis, puis retirez le couvercle arrière. 2 1 1 1. Fil de sortie 2. Capuchon de charbon 2 5. Assurez-vous que les capuchons de charbon sont bien verrouillés dans les orifices des porte-charbons. 1. Couvercle arrière 2. Vis 1 2. Soulevez le bras du ressort puis placez-le dans la partie creuse du boîtier à l’aide d’un tournevis à pointe plate et tige mince, ou d’un outil similaire. 1 2 1. Orifice 3 2 1.
Si vous désirez obtenir plus de détails sur ces accessoires, veuillez contacter le centre de service aprèsvente Makita le plus près. • Embouts-forets • Embouts-tournevis • Embout-mèche à pointe de carbure de tungstène • Poire soufflante • Support d’embout-tournevis • Crochet • Chargeur et batterie authentiques Makita NOTE : Certains éléments de la liste peuvent être inclus avec l’outil comme accessoires standards. Ils peuvent varier suivant les pays.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de taladrado XPH10 Concreto 13 mm (1/2") Acero 13 mm (1/2") Madera Capacidades de fijación Tornillo para madera 38 mm (1-1/2") 10 mm x 90 mm (3/8" x 3-1/2") Tornillo de máquina 6 mm (1/4") Velocidad sin carga (RPM) Alta (2) 0 - 1 900 r/min Baja (1) 0 - 600 r/min Golpes por minuto Alto (2) 0 - 28 500 gpm Bajo (1) 0 - 9 000 gpm Longitud total 198 mm (7-3/4") Tensión nominal Cartucho de batería estándar Peso neto •
alimentador protegido con interruptor de circuito de falla a tierra (ICFT). El uso de un ICFT reduce el riesgo de descarga eléctrica. Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2.
Advertencias de seguridad para el rotomartillo atornillador inalámbrico 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Utilice protectores de oídos al usar el taladro de percusión. La exposición al ruido puede producir pérdida auditiva. Utilice los mango(s) auxiliare(s) que se suministren con la herramienta. La pérdida de control puede ocasionar lesiones.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, libere el gatillo interruptor en la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego, vuelva a jalar el gatillo interruptor para reanudar el funcionamiento. Si la herramienta no empieza a funcionar, significa que la batería se sobrecalentó.
NOTA: Utilice un paño seco para quitar la suciedad de la lente de la lámpara. Tenga cuidado de no rayar la lente de la lámpara ya que la iluminación podría disminuir. Accionamiento del conmutador de inversión de giro A B 1 1. Palanca del interruptor de inversión PRECAUCIÓN: Confirme siempre la dirección de rotación antes de la operación. PRECAUCIÓN: Utilice el conmutador de inversión solamente después de que la herramienta haya parado completamente.
• Modo de taladrado (rotación solamente) • Modo de taladrado y martilleo (rotación con percusión) • Seleccione el modo apropiado para el trabajo en cuestión. Gire el anillo de cambio de modo de accionamiento y alinee la marca que haya seleccionado con la flecha en el cuerpo de la herramienta. Modo de atornillado (rotación con embrague) Ajuste de la torsión de apriete 2 3 1 4 1. Anillo de cambio de modo de accionamiento 2. Anillo de ajuste 3. Graduación 4.
completamente en la prensa de sujeción. Gire el mandril en sentido de las manecillas del reloj para apretar la prensa de sujeción. Para extraer la punta de destornillador/broca de taladro, gire el mandril en sentido inverso al de las manecillas del reloj. Instalación del gancho 1 OPERACIÓN PRECAUCIÓN: Siempre inserte por completo el cartucho de batería hasta que se fije en su lugar. Si puede ver la parte roja del lado superior del botón, esto indica que no ha quedado completamente fijo.
Taladrado en metal Operación de taladrado con percusión PRECAUCIÓN: En el momento de comenzar a penetrar, cuando se atasca el agujero con virutas y partículas, o cuando se topa contra varillas de refuerzo de hormigón armado, se ejerce una tremenda y repentina fuerza de torsión sobre la herramienta/broca. En primer lugar, gire el anillo de cambio de modo de accionamiento de forma que la flecha que hay en el cuerpo de la herramienta apunte a la marca.
3. Utilice tenazas para quitar las tapas de las escobillas de carbón. Quite las escobillas de carbón gastadas, inserte las nuevas y reemplace las tapas de las escobillas de carbón a la inversa. Reemplazo de las escobillas de carbón 1 1 1. Marca límite 1. Tapa de las escobillas de carbón Inspeccione regularmente las escobillas de carbón. Reemplácelas una vez que se hayan desgastado hasta la marca límite. Mantenga las escobillas de carbón limpias de forma que entren libremente en los portaescobillas.
8. Verifique la herramienta en funcionamiento y la operación del freno eléctrico cuando suelte el gatillo interruptor. Si el freno eléctrico no funciona bien, pida a su centro de servicio autorizado o de fábrica Makita que se lo repare. Para mantener la SEGURIDAD y FIABILIDAD del producto, las reparaciones, y cualquier otra tarea de mantenimiento o ajuste deberán ser realizadas en centros de servicio autorizados o de fábrica Makita, empleando siempre repuestos Makita.
34
35
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Screwdriver Visseuse sans Fil Atornillador Inalámbrico XSF03 015159 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model Capacities XSF03 Self drilling screw 6 mm (1/4") Drywall screw 5 mm (3/16") No load speed (RPM) 0 - 4,000 /min Overall length 251 mm (9-7/8") Net weight 1.5 kg (3.2 lbs) Rated voltage 1.7 kg (3.8 lbs) D.C. 18 V Standard battery cartridges BL1815 / BL1815N / BL1820 BL1830 / BL1840 / BL1850 • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
USD301-5 Tips for maintaining maximum battery life Symbols 1. The followings show the symbols used for tool. ・ volts ・ direct current ・ no load speed ・ revolutions or reciprocation per minute 2. 3. ENC007-8 IMPORTANT SAFETY INSTRUCTIONS 4. FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3.
FUNCTIONAL DESCRIPTION • 1. Switch trigger 2. Lock button 2 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1 Installing or removing battery cartridge 015162 1. Red indicator 2. Button 3. Battery cartridge 1 2 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
Electric brake Indicating remaining battery capacity This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after switch trigger release, have tool serviced at a Makita service center. 1. Battery indicator Lighting up the lamp 1 2 1. Lamp 2. Button 1 015174 When you pull the switch trigger, the battery indicator shows the remaining battery capacity. The remaining battery capacity is shown as the following table.
Overheat protection for tool When the tool is overheated, the tool stops automatically and the battery indicator shows following state. In this situation, let the tool cool before turning the tool on again. Battery indicator On Off more depth. One full turn of the locator equals 2 mm (1/16") change in depth. 1.
To remove the bit, pull the locator. Then grasp the bit with a pair of pliers and pull the bit out of the magnetic bit holder. Sometimes, it helps to wiggle the bit with the pliers as you pull. • 1. Locator 2. Bit 3. Magnetic bit holder pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury. Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Capacités XSF03 Vis taraudeuse 6 mm (1/4") Vis de plaque de plâtre 5 mm (3/16") Vitesse à vide (RPM) 0 - 4 000 /min Longueur totale 251 mm (9-7/8") Poids net 1,5 kg (3,2 lbs) Tension nominale 1,7 kg (3,8 lbs) C.C.
de changer un accessoire ou de ranger l'outil électrique. De telles mesures préventives réduisent les risques de démarrage accidentel de l'outil électrique. 20. Après l'utilisation d'un outil électrique, rangez-le hors de portée des enfants et ne laissez aucune personne l'utiliser si elle n'est pas familiarisée avec l'outil électrique ou les présentes instructions d'utilisation. Les outils électriques représentent un danger entre les mains de personnes qui n'en connaissent pas le mode d'utilisation. 21.
USD301-5 d’eau. Si le liquide pénètre dans vos yeux, il faut aussi consulter un médecin. L'électrolyte qui s'échappe de la batterie peut causer des irritations ou des brûlures. Réparation 28. Faites réparer votre outil électrique par un réparateur qualifié qui utilise des pièces de rechange identiques aux pièces d'origine. Le maintien de la sûreté de l'outil électrique sera ainsi assuré. 29. Suivez les instructions de lubrification et de changement des accessoires. 30.
10. Suivez la réglementation locale concernant la mise au rebut de la batterie. DESCRIPTION DU FONCTIONNEMENT CONSERVEZ CE MODE D'EMPLOI. • Conseils pour obtenir la durée de service maximale de la batterie 1. 2. 3. 4. Rechargez la batterie avant qu'elle ne soit complètement déchargée. Arrêtez toujours l'outil et rechargez la batterie quand vous remarquez que la puissance de l'outil diminue. Ne rechargez jamais une batterie complètement chargée.
marche. Soyez prudent lorsque vous verrouillez l'outil en position de marche, et maintenez une poigne solide sur l'outil. 2 NOTE: • Si l’outil n’est pas utilisé pendant environ 8 heures en mode d’entraînement de pression avec la gâchette verrouillée, l’outil est arrêté. Dans ce cas, relâchez la gâchette et enfoncez-la de nouveau pour redémarrer. 1. Gâchette 2. Bouton de verrouillage Frein électrique Cet outil est équipé d'un frein électrique.
Dans cette situation, éteignez l’outil et arrêtez l’application qui a causé la surcharge de l’outil. L’outil peut ensuite être rallumé. Protection de surchauffe de l’outil Lorsque l’outil surchauffe, il s’arrête automatiquement et l’indicateur de batterie présente l’état suivant. Dans cette situation, laissez refroidir l’outil avant de l’allumer de nouveau. Indication de la capacité restante de la batterie 1.
Réglage de la profondeur B 1 A ASSEMBLAGE 1. Positionneur • A ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant d'effectuer tout travail dessus. Installation et retrait du embout B 1. Positionneur 015165 Vous pouvez régler la profondeur en tournant le positionneur. Tournez-la dans le sens « B » pour réduire la profondeur, ou dans le sens « A » pour l'augmenter.
peut comporter un risque de blessure. N'utilisez les accessoires ou pièces qu'aux fins auxquelles ils ont été conçus. Si vous désirez obtenir plus de détails concernant ces accessoires, veuillez contacter le centre de service après-vente Makita le plus près. • Embouts cruciformes • Porte-embout magnétique • Chargeur et batterie authentiques Makita • Mallette de transport en plastique UTILISATION Vissage NOTE: Certains éléments de la liste peuvent être inclus avec l'outil comme accessoires standard.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo Capacidades XSF03 Tornillo de autoperforación 6 mm (1/4") Tornillo para pared "sheetrock" 5 mm (3/16") Velocidad sin carga (RPM) 0 - 4 000 r/min Longitud total 251 mm (9-7/8") Peso neto 1,5 kg (3,2 lbs) Tensión nominal 1,7 kg (3,8 lbs) 18 V c.c.
herramienta eléctrica que no pueda ser controlada con el interruptor es peligrosa y debe ser reemplazada. 19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20.
actuar creando una conexión entre las terminales de la batería. Cerrar el circuito de las terminales de la batería puede causar quemaduras o incendios. 27. En condiciones de mal uso, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. Servicio de mantenimiento 28.
8. 9. 10. Tenga cuidado de no dejar caer ni golpear el cartucho de batería. No use una batería dañada. Siga las regulaciones locales relacionadas al desecho de las baterías. DESCRIPCIÓN DEL FUNCIONAMIENTO GUARDE ESTAS INSTRUCCIONES. • Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta.
Para seleccionar el modo de operación a presión, jale ligeramente el gatillo y luego suéltelo y presione rápidamente el botón. El indicador del modo se encenderá entonces. Una vez activado la operación a presión, jale el gatillo interruptor y luego presione el botón de bloqueo. Aplique presión a la punta para iniciar la rotación del motor. Al continuar presionando más, se accionará el embrague y la punta comenzará a girar.
• Utilice un paño seco para quitar la suciedad de la lente de la lámpara. Tenga cuidado de no rayar la lente de la lámpara, porque podrá disminuir la iluminación. someten a una de las siguientes condiciones. En algunas condiciones, la luz indicadora se enciende. Protección contra sobrecarga Cuando la herramienta es utilizada de tal manera que cause un consumo anormalmente alto de corriente, la herramienta automáticamente se para sin indicación alguna.
PRECAUCIÓN: Cuando no esté utilizando la herramienta, ponga siempre la palanca del conmutador de inversión en la posición neutral. 1 1. Gancho Ajuste de la profundidad B 1 A 1. Localizador A 015170 El gancho es conveniente para cuando desea colgar la herramienta temporalmente. ENSAMBLE B 015165 La profundidad puede ajustarse al girar el localizador Gírelo a la dirección “B” para menor profundidad, y hacia la dirección “A” para mayor profundidad.
Gancho 2 MANTENIMIENTO 1. Ranura 2. Gancho 3. Tornillo 1 1 PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. • Nunca use gasolina, bencina, diluyente (tíner), alcohol o sustancias similares. Puede que esto ocasione grietas o descoloramiento.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
Cordless LED Flashlight Instruction manual Lampe Torche LED Manuel d’instructions Linterna LED Inalámbrica Manual de instrucciones DML806
6 3 2 5 4 1 1 2 7 3 2
ENGLISH Diagram Legend 1. 2. 3. 4. 5. Battery Battery Release Button Red Indicator Switch Main LED (20 pcs.) 6. 7. Sub LED (1 pc.) Metal Hook SPECIFICATIONS Model DML806 Major Features Voltage DC 14.4 V/18 V Main LED 0.5 W x 20 pcs. LED Sub LED 1.0 W x 1 pc. Standard battery cartridge Operating time Main LED (20 pcs.) when lit Main LED (10 pcs.) when lit Sub LED (1 pc.) when lit BL1415 Approx. 2.0 hours Approx. 3.5 hours Approx. 11.0 hours BL1415N Approx. 2.5 hours Approx. 4.
11. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 12. Be careful not to drop or strike battery. 13. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. CAUTION: 1. When the tool is not in use, always switch off and remove the battery cartridge from the tool. 2.
FRANÇAIS Légende du schéma 1. 2. Batterie Bouton de dégagement de la batterie 3. 4. 5. Témoin rouge Interrupteur LED principale (20 unités) 6. 7. LED secondaire (1 unité) Crochet métallique CARACTÉRISTIQUES TECHNIQUES Modèle DML806 Caractéristiques principales Tension 14,4 V c.c.
liquide qui gicle de la batterie peut provoquer des irritations ou des brûlures. 10. Ne court-circuitez pas la batterie : (1) Ne touchez pas les bornes avec un matériau conducteur. (2) Évitez de ranger la batterie dans un conteneur avec tout objet métallique tel que des clous, des pièces de monnaie, etc. (3) N’exposez pas la batterie à l’eau ou à la pluie. Un court-circuit peut causer un fort courant, une surchauffe, parfois des brûlures et même une panne de l’outil. 11.
ENTRETIEN Pour assurer le fonctionnement sûr et fiable du produit, les réparations et l'entretien doivent être effectués par un centre de service agréé Makita. ATTENTION : • N’utilisez jamais d’essence, de benzine, de solvant, d‘alcool ou tout autre produit similaire. Cela pourrait provoquer une décoloration, une déformation ou la formation de fissures. ACCESSOIRES EN OPTION ATTENTION : Ces accessoires et fixations sont recommandés pour être utilisés avec l'outil Makita spécifié dans ce manuel.
ESPAÑOL Leyenda del diagrama 1. 2. 3. Batería Botón de liberación de la batería Indicador rojo 4. 5. Interruptor LED principal (20 piezas) 6. 7.
8. No toque el interior de la cabeza de la linterna con pinzas, herramientas de metal, etc. 9. En condiciones abusivas, podrá escapar líquido de la batería, evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por atención médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. 10. No cierre el circuito entre los terminales del cartucho de batería: (1) No toque los terminales con ningún material conductor.
Presione el interruptor, como se muestra más adelante, para cambiar el modo. El LED principal (20 piezas) se enciende El LED principal (10 piezas) se enciende* El LED secundario (1 pieza) se enciende APAGADO (OFF). * Las luces LED que se encienden son las dos filas del lado del interruptor. Gancho de metal (Fig. 3) Antes de usarlo, gire verticalmente el gancho de metal sobre su eje. El gancho se puede girar en 360° y se puede retirar.
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan DML806-NA3-1214 ALA www.makita.
DC18RA DC18RC Fast Charger Chargeur rapide Cargador rápido Symbols The followings show the symbols used for the charger and battery. Be sure that you understand their meaning before use. Symboles Nous donnons ci-dessous les symboles utilisés pour le chargeur et la batterie. Assurez-vous que vous en avez bien compris la signification avant d’utiliser l’outil. Símbolos A continuación se muestran los símbolos utilizados con el cargador y la batería. Asegúrese de que entiende su significado antes de usarla.
• Do not short batteries. • Ne jamais court-circuiter les bornes d’une batterie. • No provoque un cortocircuito en las baterías. IMPORTANT: Read Before Using. IMPORTANT : Lire ce qui suit avant d’utiliser cet outil. IMPORTANTE: Leer antes de usar.
ENGLISH Specifications Model DC18RA Input DC18RC A.C. 120 V 50 – 60 HZ Output Weight D.C. 7.2 V – 18 V 0.88 kg (1.94 lbs) 0.77 kg (1.70 lbs) • Manufacturer reserves the right to change specifications without notice. • Note: Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003. IMPORTANT SAFETY INSTRUCTIONS CAUTION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
5. With finish of charge, the green light remains lit with the red light going out and the melody sound preset at the insertion of battery cartridge or buzzer sound (a long beep) comes out to notify completion of charge. (In selected silent mode, no sounds come out.) 6. Preset melody sound remains stored even when the charger is unplugged. NOTE: • The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufacturer’s batteries.
FRANÇAIS Spécifications Modèle Entrée DC18RA DC18RC C.A. 120 V 50 – 60 Hz Sortie Poids C.C. 7,2 V – 18 V 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • Le fabricant se réserve le droit de modifier sans avertissement les spécifications. • Remarque : Les spécifications peuvent varier selon les pays. • Poids selon la procédure EPTA 01/2003. LES CONSIGNES DE SECURITE IMPORTANTES ATTENTION : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Changer la mélodie de charge terminée 1. Lorsque vous insérez la batterie dans le chargeur, le chargeur émet la dernière courte mélodie préréglée d’indication de charge terminée. 2. Si vous retirez et réinsérez la batterie dans les cinq secondes qui suivent cette action, la mélodie changera. 3. Chaque fois que vous retirez et réinsérez la batterie dans les cinq secondes par la suite, la mélodie change dans l’ordre préétabli. 4.
Tension 9,6 V 12 V 14,4 V Nombre de cellules 8 10 12 Cartouche de batterie au Ni-MH Capacité (Ah) Temps de charge (en minutes) 20 — — — 1,7 BH9020A — — 2,0 20 — BH1220/C BH1420 2,0 15 20 — — — 2,7 BH9033A — — 3,3 30 — BH1233/C BH1433 3,3 22 Tension 14,4 V 18 V 14,4 V 18 V Nombre de cellules 4 5 8 10 Cartouche de batterie au Li-ion BL1415 BL1815 — — 15 — — BL1430 BL1830 22 Temps de charge (en minutes) Note : • La charge complète peut prendre jusqu’
ESPAÑOL Especificaciones Modelo DC18RA 120 V Entrada Salida Peso DC18RC 50 – 60 Hz 7,2 V cc – 18 V cc 0,88 kg (1,94 lbs) 0,77 kg (1,70 lbs) • El fabricante se reserva el derecho a cambiar las especificaciones sin aviso. • Nota: Las especificaciones podrán cambiar de un país a otro. • Peso de acuerdo con el procedimiento EPTA 01/2003. INSTRUCCIONES DE SEGURIDAD IMPORTANTES PRECAUCION: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
Cambio de la melodía de carga terminada 1. 2. 3. 4. Al insertar el cartucho de batería en el cargador se emite el último sonido de melodía breve programado. El sonido de melodía puede cambiarse extrayendo y reinsertando antes de cinco segundos el cartucho de batería. Cada vez que se extraiga y reinserte antes de otros cinco segundos, el sonido de melodía cambiará en orden. Cuando se emita el sonido de melodía deseado, deje el cartucho de batería insertado y comenzará la carga.
Tensión 9,6 V cc 12 V cc 14,4 V cc Número de celdas 8 10 12 Capacidad (Ah) Cartucho de batería Ni-MH Tiempo de carga (minutos) — — — 1,7 Ah 20 min BH9020A — — 2,0 Ah 20 min — BH1220/C BH1420 2,0 Ah 15 min — — — 2,7 Ah 20 min BH9033A — — 3,3 Ah 30 min — BH1233/C BH1433 3,3 Ah 22 min Tensión 14,4 V cc 18 V cc 14,4 V cc 18 V cc Número de celdas 4 5 8 10 Cartucho de batería Li-ion BL1415 BL1815 — — 15 min — — BL1430 BL1830 22 min Tiempo de carga (min
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884676H946 IDE www.makita.