INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Hammer Driver Drill Rotomartillo Atornillador Inalámbrico XPH12 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Drilling capacities Fastening capacities XPH12 Masonry 13 mm (1/2") Steel 13 mm (1/2") Wood 38 mm (1/1/2") Wood screw 10 mm x 90 mm (3/8" x 3-1/2") Machine screw No load speed (RPM) Blows per minute M6 (1/4") High (2) 0 - 2,000 /min Low (1) 0 - 500 /min High (2) 0 - 30,000 /min Low (1) 0 - 7,500 /min Overall length 182 mm (7-1/8") Rated voltage D.C.
4. 5. 6. 7. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Follow your local regulations relating to disposal of battery. 11. Symbols SAVE THESE INSTRUCTIONS. The followings show the symbols used for tool. CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click.
Switch action NOTE: When the tool is overheated, the tool stops automatically and the lamp starts flashing. In this case, release the switch trigger. The lamp turns off in one minute. NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action 1 ► 1.
CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the "1" side and "2" side, the tool may be damaged. 2 CAUTION: Do not use the speed change lever while the tool is running. The tool may be damaged. Displayed Number Speed Torque Applicable operation 1 Low High Heavy loading operation 2 High Low Light loading operation 1 3 4 ► 1. Action mode changing ring 2. Adjusting ring 3.
Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. 1 Installing or removing driver bit/ drill bit Optional accessory 2 1 3 ► 1. Driver bit holder 2. Driver bit 2 Fit the driver bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the driver bit holders.
Screwdriving operation Drilling operation First, turn the action mode changing ring so that the arrow points to the marking. Then proceed as follows. CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. Drilling in wood First, turn the action mode changing ring so that the arrow on the tool body points to the marking.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de taladrado XPH12 Mampostería 13 mm (1/2") Acero 13 mm (1/2") Madera Capacidades de fijación 38 mm (1/1/2") Tornillo para madera 10 mm x 90 mm (3/8" x 3-1/2") Tornillo de máquina 6 mm (1/4") Velocidad sin carga (RPM) Alta (2) 0 - 2 000 r/min Baja (1) 0 - 500 r/min Golpes por minuto Alto (2) 0 - 30 000 gpm Bajo (1) 0 - 7 500 gpm Longitud total 182 mm (7-1/8") Tensión nominal 18 V c.c.
Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2. Use equipo de protección personal. Póngase siempre protección para los ojos.
3. 4. 5. 6. 7. 8. 9. 10. Sujete la herramienta eléctrica por las superficies de agarre aisladas al realizar una operación en la que el accesorio de corte pueda estar en contacto con cables ocultos. Si el accesorio de corte entra en contacto con un cable con corriente, las piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario podrá recibir una descarga eléctrica.
Consejos para alargar al máximo la vida útil de la batería Cargue el cartucho de batería antes de que se descargue completamente. Pare siempre la operación y cargue el cartucho de batería cuando note menos potencia en la herramienta. No cargue nunca un cartucho de batería que esté completamente cargado. La sobrecarga acortará la vida de servicio de la batería. Cargue el cartucho de batería a una temperatura ambiente de 10 °C - 40 °C (50 °F - 104 °F).
Accionamiento del interruptor NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Sistema de protección para la herramienta/batería La herramienta está equipada con un sistema de protección de la herramienta/batería. Este sistema corta en forma automática el suministro de energía al motor para prolongar la vida útil de la herramienta y la batería.
NOTA: Cuando la herramienta se sobrecaliente, ésta se detendrá automáticamente y la lámpara comenzará a destellar. En este caso, suelte el gatillo interruptor. La lámpara se apagará en un minuto. NOTA: Utilice un paño seco para quitar la suciedad de la lente de la lámpara. Tenga cuidado de no rayar la lente de la lámpara ya que la iluminación podría disminuir.
Esta herramienta cuenta con tres modos de accionamiento. • Modo de taladrado (rotación solamente) • Modo de taladrado y martilleo (rotación con percusión) Modo de atornillado (rotación con embrague) • Seleccione el modo apropiado para el trabajo en cuestión. Gire el anillo de cambio de modo de accionamiento y alinee la marca que haya seleccionado con la flecha en el cuerpo de la herramienta. Ajuste de la torsión de apriete La torsión de apriete puede ajustarse en 21 niveles girando el anillo de ajuste.
Instalación del gancho OPERACIÓN PRECAUCIÓN: Siempre inserte completamente el cartucho de batería hasta que quede asegurado en su lugar. Si puede ver el indicador rojo del lado superior del botón, esto indica que no ha quedado completamente asegurado. Insértelo por completo hasta que el indicador rojo no pueda verse. De lo contrario, podría salirse accidentalmente de la herramienta y ocasionarle lesiones a usted o a alguien a su alrededor.
Taladrado en metal Operación de taladrado con percusión Para evitar que la broca de taladro resbale una vez que comience a hacer el orificio, haga un surco con punzón y un martillo en el punto a taladrar. Coloque la punta de la broca de taladro en el surco y comience a taladrar. Utilice un lubricante para corte cuando taladre metales. Salvo en el caso de hierro y bronce, los cuales deberán ser taladrados en seco.
ACCESORIOS OPCIONALES PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual. El empleo de cualquier otro accesorio o aditamento puede conllevar el riesgo de lesiones personales. Utilice los accesorios o aditamentos solamente para su fin establecido. Esta garantía le concede derechos legales específicos y usted podrá tener también otros derechos que varían de un estado a otro.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Impact Driver Atornillador de Impacto Inalámbrico XDT13 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities XDT13 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 14 mm (3/16" - 9/16") No load speed (RPM) 0 - 3,400 /min Impacts per minute 0 - 3,600 /min Overall length 126 mm (5") Rated voltage D.C. 18 V Standard battery cartridge Net weight • • • BL1815N, BL1820B BL1830, BL1830B, BL1840B, BL1850B, BL1860B 1.3 kg (2.8 lbs) 1.5 kg (3.
5. 6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery.
3. 4. 5. 6. 7. 8. 9. 10. 11. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
Overheat protection Indicating the remaining battery capacity When the tool/battery is overheated, the tool stops automatically. In this situation, let the battery cool before turning the tool on again. Only for battery cartridges with "B" at the end of the model number Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.
Lighting up the front lamp ASSEMBLY CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ socket bit 1 12 mm (15/32”) ► 1. Lamp 9 mm (3/8”) CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled.
Proper fastening torque for standard bolt NOTE: If the driver bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the driver bit will not be secured. In this case, try re-inserting the bit according to the instructions above. N•m (ft•lbs) 140 (103) NOTE: When it is difficult to insert the driver bit, pull the sleeve and insert it into the sleeve as far as it will go.
OPTIONAL ACCESSORIES NOTICE: If you use a spare battery to continue the operation, rest the tool at least 15 min. NOTE: Use the proper bit for the head of the screw/ bolt that you wish to use. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete XDT13 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 16 mm (3/16" - 5/8") Tornillo de alta resistencia 5 mm - 14 mm (3/16" - 9/16") Velocidad sin carga (rpm) 0 - 3 400 r/min Impactos por minuto 0 - 3 600 ipm Longitud total 126 mm (5") Tensión nominal 18 V c.c.
Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2. Use equipo de protección personal. Póngase siempre protección para los ojos.
2. 3. 4. 5. 6. Asegúrese siempre de que pisa sobre suelo firme. Asegúrese de que no haya nadie debajo cuando utilice la herramienta en lugares altos. Sujete la herramienta con firmeza. Póngase protectores de oídos. No toque la broca o pieza de trabajo inmediatamente después de la operación. Podrían estar extremadamente calientes y provocarle una quemadura. Mantenga las manos alejadas de las piezas giratorias. GUARDE ESTAS INSTRUCCIONES.
Indicación de la capacidad restante de la batería DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería haya sido extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Sólo para cartuchos de batería con una “B” al final del número de modelo Instalación o extracción del cartucho de batería 1 PRECAUCIÓN: Apague siempre la herramienta antes de colocar o quitar el cartucho de batería.
Protección contra sobrecarga Cuando la batería se esté utilizando de una manera que cause que consuma una cantidad de corriente anormalmente alta, la herramienta se detendrá automáticamente sin indicación alguna. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla.
Accionamiento del conmutador de inversión de giro Instalación o extracción de la punta de destornillador/punta de atornillar 12 mm (15/32”) A 9 mm (3/8”) B 1 ► 1. Palanca del interruptor de inversión Utilice únicamente la punta de destornillador/punta de atornillar que se muestra en la figura. No utilice ninguna otra punta de destornillador/punta de atornillar. PRECAUCIÓN: Confirme siempre la dirección de rotación antes de la operación.
NOTA: Si la punta de destornillador no se encuentra insertada hasta el fondo en el mandril, éste no regresará a su posición original y la punta de destornillador no quedará asegurada. En este caso, procure insertar la broca de nuevo siguiendo las instrucciones de arriba. NOTA: Si tiene dificultades para insertar la punta de destornillador, jale el mandril e inserte la broca tanto como sea posible.
Sujete la herramienta firmemente y coloque la punta de destornillador en la cabeza del tornillo. Aplique presión frontal a la herramienta de manera que la broca no se deslice del tornillo y encienda la herramienta para comenzar la operación. Para mantener la SEGURIDAD y FIABILIDAD del producto, las reparaciones, y cualquier otra tarea de mantenimiento o ajuste deberán ser realizadas en centros de servicio autorizados o de fábrica Makita, empleando siempre repuestos Makita.
EN NINGÚN CASO MAKITA SE HARÁ RESPONSABLE DE NINGÚN DAÑO INDIRECTO, INCIDENTAL, O DERIVADO DE LA VENTA O USO DEL PRODUCTO. ESTE DESCARGO DE RESPONSABILIDAD APLICA DURANTE Y DESPUÉS DEL PLAZO DE ESTA GARANTÍA. MAKITA RENUNCIA A LA RESPONSABILIDAD POR CUALQUIER GARANTÍA IMPLÍCITA, INCLUYENDO GARANTÍAS DE “COMERCIABILIDAD” Y “ADECUACIÓN PARA UN PROPÓSITO ESPECÍFICO”, DESPUÉS DEL PLAZO DE UN AÑO DE ESTA GARANTÍA.
18
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Multi Tool Outil Multi-Fonctions Sans Fil Multitool Inalámbrica XMT03 014551 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XMT03 Oscillation per minute 6,000 - 20,000 /min 1.6 ゚ (3.2 ゚ total) Oscillation angle, left/right Standard battery cartridge BL1830/BL1840 BL1815/BL1815N * Overall length 340 mm (13-3/8") 326 mm (12-7/8") Net weight 2.2 kg (4.9 lbs) Rated voltage 2.0 kg (4.4 lbs) D.C. 18 V * NOTE: For continuous operation, high capacity battery cartridge BL1830 and BL1840 is recommended.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Do not leave the tool running. Operate the tool only when hand-held. Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece. Do not touch the application tool or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Do not operate the tool at no-load unnecessarily.
4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6.
Battery protection system (Lithium-ion battery with star marking) CAUTION: Before installing the battery cartridge into the tool, always check to see that the tool is switched off. To start the tool, slide the slide switch toward the "I (ON)" position. To stop the tool, slide the slide switch toward the "O (OFF)" position. • 1. Star marking 1 Adjusting the orbital stroke rate 1. Dial 1 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
ASSEMBLY • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing application tool (optional accessory) • • 014564 When using sanding application tool, mount the application tool on the sanding pad so that it matches the sanding pad direction. The sanding pad has a hook and loop type fitting system which allows easy and rapid fitting of a sanding paper.
Dust extraction attachment (optional accessory) 1 014559 Put the application tool on the workpiece. And then move the tool forward so that the application tool movement does not slow down. 7 8 NOTE: • Forcing or excessive pressure on the tool may reduce efficiency. • Before cutting operation, it is recommended to preset the orbital stroke rate 4 - 6. • Remove sawdust by drawing the tool adequately. It increases work efficiency. • The round saw is recommended for cutting long straight line.
MAINTENANCE MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XMT03 Oscillation par minute 6 000 - 20 000 /min 1,6 ゚ (3,2 ゚ total) Angle d’oscillation gauche/droite Batterie standard BL1830/BL1840 BL1815/BL1815N * Longueur totale 340 mm (13-3/8") 326 mm (12-7/8") Poids net 2,2 kg (4,9 lbs) Tension nominale 2,0 kg (4,4 lbs) C.C. 18 V * REMARQUE : Pour un fonctionnement continu, il est recommandé d’utiliser les batteries haute capacité BL1830 et BL1840.
11. Portez des dispositifs de protection personnelle. Portez toujours un protecteur pour la vue. Les risques de blessure seront moins élevés si vous utilisez des dispositifs de protection tels qu'un masque antipoussières, des chaussures à semelle antidérapante, une coiffure résistante ou une protection d'oreilles. 12. Évitez les démarrages accidentels.
11. Réparation 28. Faites réparer votre outil électrique par un réparateur qualifié qui utilise des pièces de rechange identiques aux pièces d'origine. Le maintien de la sûreté de l'outil électrique sera ainsi assuré. 29. Suivez les instructions de lubrification et de changement des accessoires. 30. Maintenez les poignées de l'outil sèches, propres et exemptes d'huile ou de graisse. 12. 13. 14. GEB094-2 CONSIGNES DE SÉCURITÉ POUR L'OUTIL MULTIFONCTION SANS FIL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 15.
23. 24. 25. 26. 27. Ne faites pas fonctionner l’outil lorsque vous le transportez. Un contact accidentel avec l’accessoire pourrait accrocher vos vêtements et l’entraîner vers votre corps. N'utilisez pas l'outil électrique près de matériaux inflammables. Les étincelles qui jaillissent de l'outil risqueraient de faire prendre en feu ces matériaux. N'utilisez pas d'accessoires nécessitant de réfrigérants fluides.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) DESCRIPTION DU FONCTIONNEMENT 1. Étoile 1 • AVERTISSEMENT: Assurez-vous toujours que l’outil est hors tension et la batterie retirée avant d'effectuer un réglage ou de vérifier le fonctionnement de l’outil. Si vous ne respectez pas cette précaution, vous risquez de graves blessures dues à un démarrage accidentel.
ATTENTION: Avant d’installer la batterie dans l’outil, vérifiez toujours que ce dernier est hors tension. Pour démarrer l’outil, faites glisser l’interrupteur sur la position « I (ON) ». Pour arrêter l’outil, faites glisser l’interrupteur sur la position « O (OFF) ».
3. Insérez le boulon de retenue jusqu’à ce qu’il s’arrête. Ramenez ensuite le levier de verrouillage à sa position de départ. bord tranchant. Cela risque d’endommager l’outil. 014559 Mettez l'outil d'application sur l'ouvrage. Déplacez ensuite l’outil vers l’avant, pour que le mouvement de l’outil d’application ne ralentisse pas. 014564 Lorsque vous utilisez un outil d’application destiné au ponçage, montez-le sur le patin de ponçage dans le même sens.
Extracteur de poussière (accessoire en option) ENTRETIEN ATTENTION: Assurez-vous toujours que l'outil est hors tension et que la batterie est retirée avant d'y effectuer tout travail d'inspection ou d'entretien. • N'utilisez jamais d'essence, de benzine, de solvant, d'alcool ou d'autres produits similaires. Une décoloration, une déformation, ou la formation de fissures peuvent en découler.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XMT03 Oscilaciones por minuto 6 000 - 20 000 r/min 1,6 ゚ (3,2 ゚ en total) Ángulo de oscilación, izquierda/derecha Cartucho de batería estándar BL1830/BL1840 BL1815/BL1815N * Longitud total 340 mm (13-3/8") 326 mm (12-7/8") Peso neto 2,2 kg (4,9 lbs) Tensión nominal 2,0 kg (4,4 lbs) 18 V c.c. * NOTA: Para una operación continua, se recomienda el uso del cartucho de batería de alta capacidad BL1830 y BL1840.
cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera la máquina puede dar como resultado heridas personales graves. 11. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá las heridas personales. 12. Impida el encendido accidental.
29. 30. Siga las instrucciones para la lubricación y cambio de accesorios. Mantenga las agarraderas secas, limpias y sin aceite o grasa. 13. 14. GEB094-2 ADVERTENCIAS DE SEGURIDAD PARA EL MULTIFUNCIONAL INALÁMBRICO 15. 1. Esta herramienta motorizada está diseñada para el aserrado, corte, esmerilado y lijado. Lea todas las advertencias de seguridad, instrucciones, ilustraciones y especificaciones que se incluyen con esta herramienta eléctrica.
24. 25. 26. 27. 4. No opere la herramienta motorizada cerca de materiales inflamables. Las chispas podrían inflamar estos materiales. No utilice accesorios que requieran de líquidos enfriadores. El uso de agua o de cualquier otro líquido enfriador puede que resulte en descargas eléctricas o electrocución. Asegúrese siempre de que la herramienta esté apagada y desenchufada, o que el cartucho de batería se haya extraído antes de realizar cualquier trabajo en la herramienta.
Sistema de protección de batería (batería de ión de litio con marca de estrella) DESCRIPCIÓN DEL FUNCIONAMIENTO 1 • ADVERTENCIA: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o revisión del funcionamiento de la herramienta. No seguir esta indicación de apagar y quitar el cartucho de batería puede que resulte en graves lesiones a la persona debido al encendido accidental.
Cuando la capacidad restante de la batería llega a reducirse, la luz indicadora de la batería parpadeará. • Cuando la capacidad restante de la batería llega a un nivel mucho más reducido, la herramienta se detiene durante la operación y la luz indicadora se ilumina por alrededor de diez segundos. En este momento, retire el cartucho de la batería de la herramienta y recárguelo. • Accionamiento del interruptor 1 1.
2 1 2 3 OPERACIÓN 1. Perno sujetador 2. Orificios en la pieza de aplicación 3. Protuberancias en la brida de la herramienta • 1 • 014553 3. Inserte el perno sujetador hasta que se detenga. Luego vuelva a colocar la palanca de bloqueo a su posición original. ADVERTENCIA: Antes de arrancar la herramienta, así como durante la operación, mantenga sus manos y rostro alejados de la herramienta de la aplicación.
• • • Instale las boquillas y el aditamento para polvo. Instale la cinta de boquilla sobre la herramienta de tal forma que sus protuberancias encajen en los orificios en la herramienta para que quede fija. Coloque el aro de fieltro y la almohadilla de lijado sobre el aditamento para polvo, y luego fíjelos con el perno de instalación de la pieza de aplicación. 014560 Aplique el papel de lijado a la pieza de trabajo.
• • • • • • • • • • • • • • • Raspador (flexible) Cuchilla de sierra segmentada Cortador de junturas en general Removedor HM Hoja de sierra dentada HM Placa HM de lijado Hoja de sierra de diamante Papel de lijado Adaptador Papel delta abrasivo (rojo / blanco / negro) Felpa delta (medio / áspero / sin grano) Fieltro delta para pulido Llave hexagonal Aditamento de extracción de polvo Batería y cargador originales de Makita GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de ga
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.