INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Hammer Driver Drill Rotomartillo Atornillador Inalámbrico XPH12 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Drilling capacities Fastening capacities XPH12 Masonry 13 mm (1/2") Steel 13 mm (1/2") Wood 38 mm (1/1/2") Wood screw 10 mm x 90 mm (3/8" x 3-1/2") Machine screw No load speed (RPM) Blows per minute M6 (1/4") High (2) 0 - 2,000 /min Low (1) 0 - 500 /min High (2) 0 - 30,000 /min Low (1) 0 - 7,500 /min Overall length 182 mm (7-1/8") Rated voltage D.C.
4. 5. 6. 7. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Follow your local regulations relating to disposal of battery. 11. Symbols SAVE THESE INSTRUCTIONS. The followings show the symbols used for tool. CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click.
Switch action NOTE: When the tool is overheated, the tool stops automatically and the lamp starts flashing. In this case, release the switch trigger. The lamp turns off in one minute. NOTE: Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Reversing switch action 1 ► 1.
CAUTION: Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the "1" side and "2" side, the tool may be damaged. 2 CAUTION: Do not use the speed change lever while the tool is running. The tool may be damaged. Displayed Number Speed Torque Applicable operation 1 Low High Heavy loading operation 2 High Low Light loading operation 1 3 4 ► 1. Action mode changing ring 2. Adjusting ring 3.
Installing driver bit holder ASSEMBLY Optional accessory CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. 1 Installing or removing driver bit/ drill bit Optional accessory 2 1 3 ► 1. Driver bit holder 2. Driver bit 2 Fit the driver bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the driver bit holders.
Screwdriving operation Drilling operation First, turn the action mode changing ring so that the arrow points to the marking. Then proceed as follows. CAUTION: Adjust the adjusting ring to the proper torque level for your work. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or driver bit may be damaged. Drilling in wood First, turn the action mode changing ring so that the arrow on the tool body points to the marking.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de taladrado XPH12 Mampostería 13 mm (1/2") Acero 13 mm (1/2") Madera Capacidades de fijación 38 mm (1/1/2") Tornillo para madera 10 mm x 90 mm (3/8" x 3-1/2") Tornillo de máquina 6 mm (1/4") Velocidad sin carga (RPM) Alta (2) 0 - 2 000 r/min Baja (1) 0 - 500 r/min Golpes por minuto Alto (2) 0 - 30 000 gpm Bajo (1) 0 - 7 500 gpm Longitud total 182 mm (7-1/8") Tensión nominal 18 V c.c.
Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2. Use equipo de protección personal. Póngase siempre protección para los ojos.
3. 4. 5. 6. 7. 8. 9. 10. Sujete la herramienta eléctrica por las superficies de agarre aisladas al realizar una operación en la que el accesorio de corte pueda estar en contacto con cables ocultos. Si el accesorio de corte entra en contacto con un cable con corriente, las piezas metálicas expuestas de la herramienta eléctrica se cargarán también de corriente y el operario podrá recibir una descarga eléctrica.
Consejos para alargar al máximo la vida útil de la batería Cargue el cartucho de batería antes de que se descargue completamente. Pare siempre la operación y cargue el cartucho de batería cuando note menos potencia en la herramienta. No cargue nunca un cartucho de batería que esté completamente cargado. La sobrecarga acortará la vida de servicio de la batería. Cargue el cartucho de batería a una temperatura ambiente de 10 °C - 40 °C (50 °F - 104 °F).
Accionamiento del interruptor NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Sistema de protección para la herramienta/batería La herramienta está equipada con un sistema de protección de la herramienta/batería. Este sistema corta en forma automática el suministro de energía al motor para prolongar la vida útil de la herramienta y la batería.
NOTA: Cuando la herramienta se sobrecaliente, ésta se detendrá automáticamente y la lámpara comenzará a destellar. En este caso, suelte el gatillo interruptor. La lámpara se apagará en un minuto. NOTA: Utilice un paño seco para quitar la suciedad de la lente de la lámpara. Tenga cuidado de no rayar la lente de la lámpara ya que la iluminación podría disminuir.
Esta herramienta cuenta con tres modos de accionamiento. • Modo de taladrado (rotación solamente) • Modo de taladrado y martilleo (rotación con percusión) Modo de atornillado (rotación con embrague) • Seleccione el modo apropiado para el trabajo en cuestión. Gire el anillo de cambio de modo de accionamiento y alinee la marca que haya seleccionado con la flecha en el cuerpo de la herramienta. Ajuste de la torsión de apriete La torsión de apriete puede ajustarse en 21 niveles girando el anillo de ajuste.
Instalación del gancho OPERACIÓN PRECAUCIÓN: Siempre inserte completamente el cartucho de batería hasta que quede asegurado en su lugar. Si puede ver el indicador rojo del lado superior del botón, esto indica que no ha quedado completamente asegurado. Insértelo por completo hasta que el indicador rojo no pueda verse. De lo contrario, podría salirse accidentalmente de la herramienta y ocasionarle lesiones a usted o a alguien a su alrededor.
Taladrado en metal Operación de taladrado con percusión Para evitar que la broca de taladro resbale una vez que comience a hacer el orificio, haga un surco con punzón y un martillo en el punto a taladrar. Coloque la punta de la broca de taladro en el surco y comience a taladrar. Utilice un lubricante para corte cuando taladre metales. Salvo en el caso de hierro y bronce, los cuales deberán ser taladrados en seco.
ACCESORIOS OPCIONALES PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual. El empleo de cualquier otro accesorio o aditamento puede conllevar el riesgo de lesiones personales. Utilice los accesorios o aditamentos solamente para su fin establecido. Esta garantía le concede derechos legales específicos y usted podrá tener también otros derechos que varían de un estado a otro.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Impact Driver Atornillador de Impacto Inalámbrico XDT13 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities XDT13 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 14 mm (3/16" - 9/16") No load speed (RPM) 0 - 3,400 /min Impacts per minute 0 - 3,600 /min Overall length 126 mm (5") Rated voltage D.C. 18 V Standard battery cartridge Net weight • • • BL1815N, BL1820B BL1830, BL1830B, BL1840B, BL1850B, BL1860B 1.3 kg (2.8 lbs) 1.5 kg (3.
5. 6. 7. Service 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 2. Follow instruction for lubricating and changing accessories. 3. Keep handles dry, clean and free from oil and grease. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery.
3. 4. 5. 6. 7. 8. 9. 10. 11. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
Overheat protection Indicating the remaining battery capacity When the tool/battery is overheated, the tool stops automatically. In this situation, let the battery cool before turning the tool on again. Only for battery cartridges with "B" at the end of the model number Overdischarge protection When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.
Lighting up the front lamp ASSEMBLY CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing driver bit/ socket bit 1 12 mm (15/32”) ► 1. Lamp 9 mm (3/8”) CAUTION: Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled.
Proper fastening torque for standard bolt NOTE: If the driver bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the driver bit will not be secured. In this case, try re-inserting the bit according to the instructions above. N•m (ft•lbs) 140 (103) NOTE: When it is difficult to insert the driver bit, pull the sleeve and insert it into the sleeve as far as it will go.
OPTIONAL ACCESSORIES NOTICE: If you use a spare battery to continue the operation, rest the tool at least 15 min. NOTE: Use the proper bit for the head of the screw/ bolt that you wish to use. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete XDT13 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 16 mm (3/16" - 5/8") Tornillo de alta resistencia 5 mm - 14 mm (3/16" - 9/16") Velocidad sin carga (rpm) 0 - 3 400 r/min Impactos por minuto 0 - 3 600 ipm Longitud total 126 mm (5") Tensión nominal 18 V c.c.
Seguridad personal 1. Manténgase alerta, preste atención a lo que está haciendo y utilice su sentido común cuando opere una herramienta eléctrica. No utilice una herramienta eléctrica cuando esté cansado o bajo la influencia de drogas, alcohol o medicamentos. Un momento de distracción mientras opera las herramientas eléctricas puede terminar en una lesión grave. 2. Use equipo de protección personal. Póngase siempre protección para los ojos.
2. 3. 4. 5. 6. Asegúrese siempre de que pisa sobre suelo firme. Asegúrese de que no haya nadie debajo cuando utilice la herramienta en lugares altos. Sujete la herramienta con firmeza. Póngase protectores de oídos. No toque la broca o pieza de trabajo inmediatamente después de la operación. Podrían estar extremadamente calientes y provocarle una quemadura. Mantenga las manos alejadas de las piezas giratorias. GUARDE ESTAS INSTRUCCIONES.
Indicación de la capacidad restante de la batería DESCRIPCIÓN DEL FUNCIONAMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería haya sido extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Sólo para cartuchos de batería con una “B” al final del número de modelo Instalación o extracción del cartucho de batería 1 PRECAUCIÓN: Apague siempre la herramienta antes de colocar o quitar el cartucho de batería.
Protección contra sobrecarga Cuando la batería se esté utilizando de una manera que cause que consuma una cantidad de corriente anormalmente alta, la herramienta se detendrá automáticamente sin indicación alguna. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla.
Accionamiento del conmutador de inversión de giro Instalación o extracción de la punta de destornillador/punta de atornillar 12 mm (15/32”) A 9 mm (3/8”) B 1 ► 1. Palanca del interruptor de inversión Utilice únicamente la punta de destornillador/punta de atornillar que se muestra en la figura. No utilice ninguna otra punta de destornillador/punta de atornillar. PRECAUCIÓN: Confirme siempre la dirección de rotación antes de la operación.
NOTA: Si la punta de destornillador no se encuentra insertada hasta el fondo en el mandril, éste no regresará a su posición original y la punta de destornillador no quedará asegurada. En este caso, procure insertar la broca de nuevo siguiendo las instrucciones de arriba. NOTA: Si tiene dificultades para insertar la punta de destornillador, jale el mandril e inserte la broca tanto como sea posible.
Sujete la herramienta firmemente y coloque la punta de destornillador en la cabeza del tornillo. Aplique presión frontal a la herramienta de manera que la broca no se deslice del tornillo y encienda la herramienta para comenzar la operación. Para mantener la SEGURIDAD y FIABILIDAD del producto, las reparaciones, y cualquier otra tarea de mantenimiento o ajuste deberán ser realizadas en centros de servicio autorizados o de fábrica Makita, empleando siempre repuestos Makita.
EN NINGÚN CASO MAKITA SE HARÁ RESPONSABLE DE NINGÚN DAÑO INDIRECTO, INCIDENTAL, O DERIVADO DE LA VENTA O USO DEL PRODUCTO. ESTE DESCARGO DE RESPONSABILIDAD APLICA DURANTE Y DESPUÉS DEL PLAZO DE ESTA GARANTÍA. MAKITA RENUNCIA A LA RESPONSABILIDAD POR CUALQUIER GARANTÍA IMPLÍCITA, INCLUYENDO GARANTÍAS DE “COMERCIABILIDAD” Y “ADECUACIÓN PARA UN PROPÓSITO ESPECÍFICO”, DESPUÉS DEL PLAZO DE UN AÑO DE ESTA GARANTÍA.
18
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Recipro Saw Scie Recipro sans Fil Sierra Recíproca Inalámbrica XRJ01 XRJ04 014043 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XRJ01 XRJ04 Length of stroke 13 mm (1/2") Strokes per minute Overall length Net weight 0 - 3,000 /min Pipe Max. cutting capacities 50 mm (2") Wood 50 mm (2") with BL1815 392 mm (15-1/2") with BL1830 / BL1840 398 mm (15-5/8") with BL1815 1.5 kg (3.4 lbs) with BL1830 / BL1840 1.5 kg (3.3 lbs) 1.8 kg (3.9 lbs) Rated voltage D.C. 18 V Standard battery cartridge(s) Warning: Use only the battery(ies) described.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
7. 8. 9. 10. 11. 12. 13. 14. 15. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material.
Battery protection system (Lithium-ion battery with star marking) FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1. Star marking 1 Installing or removing battery cartridge 1. Red indicator 2. Button 3. Battery cartridge 1 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
To start the tool, pull either switch lever or trigger. • For the switch lever, pull the lock-off lever and then pull the switch lever to start the tool. • For the switch trigger, depress the lock-off button and then pull the switch trigger to start to the tool. The lock-off button can be pressed from either right or left. The tool speed is increased by increasing pressure on the switch lever/trigger. Release the switch lever/trigger to stop.
NOTE: • If you remove the saw blade without rotating the blade clamp sleeve fully, the sleeve may not be fixed. In this case, rotate the blade clamp sleeve fully, then make the sleeve fixed at the released position. For Model XRJ04 3 1 1. Hex wrench 2. Bolt 3. Loosen 4. Tighten 4 1 2 2 014045 4 3 1 1. Saw blade 2. Blade clamp 3. Hole for recipro saw blade 4. Hole for jig saw blade 014047 2 3 4 014086 You can use both jig saw blades (B type) and recipro saw blades according to your work.
OPERATION • • • • NOTE: • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. CAUTION: Always press the shoe firmly against the workpiece during operation. If the shoe is held away from the workpiece during operation, strong vibration and/or twisting will be produced, causing the blade to snap dangerously. Always wear gloves to protect your hands from hot flying chips when cutting metal.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XRJ01 XRJ04 Longueur de frappe 13 mm (1/2") Nombre d'impacts par minute Longueur totale Poids net 0 - 3 000 /min Tuyau Capacités de coupe max. 50 mm (2") Bois 50 mm (2") avec modèle BL1815 392 mm (15-1/2") avec modèle BL1830 / BL1840 398 mm (15-5/8") avec modèle BL1815 1,5 kg (3,4 lbs) avec modèle BL1830 / BL1840 1,5 kg (3,3 lbs) 1,8 kg (3,9 lbs) Tension nominale C.C.
Utilisation et entretien des outils électriques 17. Ne forcez pas l'outil électrique. Utilisez l'outil électrique adéquat suivant le type de travail à effectuer. Si vous utilisez l'outil électrique adéquat et respectez le régime pour lequel il a été conçu, il effectuera un travail de meilleure qualité et de façon plus sécuritaire. 18. N'utilisez pas l'outil électrique s'il n'est pas possible de mettre sa gâchette en position de marche et d'arrêt.
5. 25. N'utilisez un outil électrique qu'avec le blocpiles conçu spécifiquement pour cet outil. Il y a risque de blessure ou d'incendie si un autre bloc-piles est utilisé. 26. Lorsque vous n'utilisez pas le bloc-piles, rangez-le à l'écart des objets métalliques tels que trombones, pièces de monnaie, clés, clous, vis ou autres petits objets métalliques qui risquent d'établir une connexion entre les bornes. La mise en court-circuit des bornes de batterie peut causer des brûlures ou un incendie. 27.
USD301-1 10. Symboles CONSERVEZ CE MODE D'EMPLOI. Les symboles utilisés pour l'outil sont indiqués cidessous. ・ volts ・ courant continu ・ vitesse à vide ・ tours ou alternances par minute Conseils pour obtenir la durée de service maximale de la batterie 1. ENC007-8 2. CONSIGNES DE SÉCURITÉ IMPORTANTES 3. POUR LA BATTERIE 1. 2. 3. 4. 5. 6. 7. 8. 9. Suivez la réglementation locale concernant la mise au rebut de la batterie.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) DESCRIPTION DU FONCTIONNEMENT 1. Étoile 1 • ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. Installation ou retrait de la batterie 1. Indicateur rouge 2. Bouton 3. Batterie 1 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection.
durée de service de la lame. Pour repositionner le sabot, desserrez le boulon avec une clé hexagonale. Faites glisser le sabot à la position de votre choix et serrez le boulon fermement. Un levier/bouton de sécurité est prévu pour prévenir la pression accidentelle sur le levier de l'interrupteur/gâchette. Pour faire démarrer l’outil, appuyez sur le levier de l’interrupteur ou sur la gâchette.
Pour retirer la lame, faites complètement tourner le collet de la porte-lame dans le sens indiqué par la flèche. La lame se dégagera et le collet de la porte-lame sera maintenu en position ouverte. NOTE: • Si vous retirez la lame sans faire complètement tourner le collet de la porte-lame, il se peut que le collet ne soit pas immobilisé. Dans ce cas, faites complètement tourner le collet de la porte-lame pour immobiliser le collet en position ouverte. Pour le modèle XRJ04 3 1 2 1. Clé hexagonale 2.
Lorsque vous n'utilisez pas la clé hexagonale, rangez-la de la façon indiquée sur l'illustration pour éviter de l'égarer. UTILISATION • • • • ATTENTION: Appliquez toujours fermement le sabot contre la pièce pendant l'utilisation. Si le sabot s'éloigne de la pièce pendant l'opération, cela causera de fortes vibrations et/ou torsions, faisant claquer la lame dangereusement. Portez toujours des gants pour protéger vos mains des projections de copeaux chauds pendant la coupe du métal.
NOTE: • Certains éléments de la liste peuvent être inclus avec l'outil comme accessoires standard. Ils peuvent varier suivant les pays. GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XRJ01 XRJ04 Extensión de la carrera 13 mm (1/2") Carreras por minuto Longitud total Peso neto 0 - 3 000 cpm Tubo Capacidad máxima de corte 50 mm (2") Madera 50 mm (2") con BL1815 392 mm (15-1/2") con BL1830 / BL1840 398 mm (15-5/8") con BL1815 1,5 kg (3,4 lbs) con BL1830 / BL1840 1,5 kg (3,3 lbs) 1,8 kg (3,9 lbs) Tensión nominal 18 V c.c. Cartucho(s) de batería estándar Advertencia: Use solamente la(s) batería(s) indicada(s).
18. No utilice la herramienta eléctrica si el interruptor no la enciende y apaga. Cualquier herramienta eléctrica que no pueda ser controlada con el interruptor es peligrosa y debe ser reemplazada. 19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20.
7. 8. monedas, llaves, clavos, tornillos u otros objetos pequeños de metal los cuales pueden actuar creando una conexión entre las terminales de la batería. Cerrar el circuito de las terminales de la batería puede causar quemaduras o incendios. 27. En condiciones de mal uso, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica.
ENC007-8 Consejos para alargar al máximo la vida útil de la batería INSTRUCCIONES IMPORTANTES DE SEGURIDAD 1. PARA CARTUCHO DE BATERÍA 1. Antes de utilizar el cartucho de batería, lea todas las instrucciones e indicaciones de precaución sobre (1) el cargador de baterías, (2) la batería, y (3) el producto con el que se utiliza la batería. 2. No desarme el cartucho de batería. 3. Si el tiempo de operación se ha acortado en exceso, deje de operar de inmediato.
Sistema de protección de batería (batería de ión de litio con marca de estrella) DESCRIPCIÓN DEL FUNCIONAMIENTO 1 • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Instalación o desmontaje del cartucho de batería 012128 Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección.
2 3 Regulación de la zapata 1. Botón lock-off (bloqueo desactivado) 2. Palanca de desbloqueo 3. Gatillo del interruptor 4. Gatillo interruptor 1 3 4 1. Llave hexagonal 2. Tornillo hexagonal 3. Aflojar 2 1 014050 Se dispone de un botón / una palanca de desbloqueo del gatillo interruptor / de la palanca interruptora para evitar que se accione accidentalmente. Para arrancar la herramienta, jale ya sea el gatillo interruptor o palanca interruptora.
• PRECAUCIÓN: Si no inserta la hoja de sierra suficientemente a tope, la hoja de sierra podría salirse inesperadamente durante la operación. Esto puede ser muy peligroso. 1 NOTA: • No se puede usar la segueta caladora con el modelo XRJ01. 1. Disco de sierra 2. Manguito de sujeción de la sierra 2 3 014059 1. Sierra de sable 2. Llave hexagonal 3. Orificio para la segueta recíproca 4.
014086 014054 Puede usar tanto seguetas caladoras (tipo B), así como seguetas recíprocas según corresponda con la operación a ser realizada. Inserte la segueta de directamente en la prensa de la misma y apriétela con la llave hexagonal. Jale la segueta ligeramente para asegurar que ésta no pueda salirse durante la operación. Para quitar la segueta, siga el procedimiento de instalación a la inversa. Presione la zapata firmemente contra la pieza de trabajo. No permita que la herramienta dé saltos.
MANTENIMIENTO GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. • Nunca use gasolina, bencina, diluyente (tíner), alcohol o sustancias similares. Puede que esto ocasione grietas o descoloramiento.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.