INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Hammer Driver Drill Perceuse Percussion-Visseuse sans Fil Rotomartillo Atornillador Inalámbrico XPH01 XPH02 011491 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model Concrete Capacities XPH01 XPH02 13 mm (1/2") 13 mm (1/2") Steel 13 mm (1/2") 13 mm (1/2") Wood 38 mm (1-1/2") 38 mm (1-1/2") 6 mm x 75 mm (1/4" x 2-15/16") Wood screw 10 mm x 89 mm (3/8" x 3-1/2") Machine screw M6 (1/4") M6 (1/4") High (2) 0 - 1,500 /min 0 - 1,500 /min No load speed (RPM) Blows per minute Low (1) 0 - 400 /min 0 - 400 /min High (2) 0 - 22,500 /min 0 - 22,500 /min Low (1) Overall length Net weight 0 - 6,000 /min
tool for operations different from those intended could result in a hazardous situation. Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
6. 7. 8. 9. 10. Hold the tool firmly. Keep hands away from rotating parts. Do not leave the tool running. Operate the tool only when hand-held. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. 5.
• Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the trigger switch on the tool and stop the application that caused the tool to become overloaded. Then pull the trigger switch again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the trigger switch again. Low battery voltage: The remaining battery capacity is too low and the tool will not operate.
Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out 10 -15 seconds after releasing the trigger. To change the speed, first switch off the tool and then slide the speed change lever to the "2" side for high speed or "1" side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. NOTE: • Use a dry cloth to wipe the dirt off the lens of the lamp.
ASSEMBLY • OPERATION CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly. • Always secure small workpieces in a vise or with a similar hold-down device. • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1. Rear cover 2. Screw 1 2 OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle Béton Capacités XPH01 XPH02 13 mm (1/2") 13 mm (1/2") Acier 13 mm (1/2") 13 mm (1/2") Bois 38 mm (1-1/2") 38 mm (1-1/2") 6 mm x 75 mm (1/4" x 2-15/16") Vis à bois 10 mm x 89 mm (3/8" x 3-1/2") Vis de mécanique M6 (1/4") M6 (1/4") Grande (2) 0 - 1 500 /min 0 - 1 500 /min Vitesse à vide (T/MIN) Nombre de frappes par minute Réduite (1) 0 - 400 /min 0 - 400 /min Grande (2) 0 - 22 500 /min 0 - 22 500 /min Réduite (1) Longueur tot
Utilisation et entretien des outils électriques 17. Ne forcez pas l'outil électrique. Utilisez l'outil électrique adéquat suivant le type de travail à effectuer. Si vous utilisez l'outil électrique adéquat et respectez le régime pour lequel il a été conçu, il effectuera un travail de meilleure qualité et de façon plus sécuritaire. 18. N'utilisez pas l'outil électrique s'il n'est pas possible de mettre sa gâchette en position de marche et d'arrêt.
25. N'utilisez un outil électrique qu'avec le bloc-piles conçu spécifiquement pour cet outil. Il y a risque de blessure ou d'incendie si un autre bloc-piles est utilisé. 26. Lorsque vous n'utilisez pas le bloc-piles, rangez-le à l'écart des objets métalliques tels que trombones, pièces de monnaie, clés, clous, vis ou autres petits objets métalliques qui risquent d'établir une connexion entre les bornes. La mise en court-circuit des bornes de batterie peut causer des brûlures ou un incendie. 27.
ENC007-8 2. CONSIGNES DE SÉCURITÉ IMPORTANTES 3. POUR LA BATTERIE 1. Avant d'utiliser la batterie, lisez toutes les instructions et précautions relatives (1) au chargeur de batterie, (2) à la batterie, et (3) à l'outil utilisant la batterie. 2. Ne démontez pas la batterie. 3. Cessez immédiatement l'utilisation si le temps de fonctionnement devient excessivement court. Il y a risque de surchauffe, de brûlures, voire d'explosion. 4.
L'outil s’arrête automatiquement pendant l'utilisation lorsque l'outil et/ou la batterie sont dans l’une des situations suivantes : • En surcharge : L'outil est utilisé d’une manière entraînant une consommation anormale de courant. Dans cette situation, relâchez la gâchette et arrêtez l'activité qui entraîne une surcharge de l'outil. Puis appuyez de nouveau sur la gâchette pour redémarrer. Si l’outil ne démarre pas, la batterie est en surchauffe.
ATTENTION: Evitez de regarder directement le faisceau lumineux ou sa source. Appuyez sur la gâchette pour allumer la lampe. La lampe demeure allumée tant que la pression sur la gâchette est maintenue. La lampe s'éteint de 10 à 15 secondes après la libération de la gâchette. ATTENTION: Réglez toujours le levier de changement de vitesse à fond sur la position voulue.
Réglage du couple de serrage 1 2 3 Installation du crochet 1. Bague de changement de mode d'action 2. Bague de réglage 3. Graduation 4. Flèche 1 2 4 1. Rainure 2. Crochet 3. Vis 3 011496 011498 Le couple de serrage est réglable sur l'une ou l'autre de 16 positions, en tournant la bague de réglage de sorte que ses graduations soient alignées sur la flèche du bâti de l'outil.
Placez la pointe de l'embout dans la tête de vis et appliquez une pression sur l'outil. Faites démarrer l'outil à vitesse réduite puis augmentez graduellement la vitesse. Relâchez la gâchette dès que l'engrenage s'active. Perçage avec martelage ATTENTION: Une force de torsion énorme et soudaine s'exerce sur l'outil et le foret lors du perçage du trou, lorsque ce dernier est bouché par des copeaux et particules ou lorsque le foret frappe contre les armatures d'une structure en béton armé.
Perçage du bois Quand vous percez dans du bois, vous obtiendrez de meilleurs résultats avec des forets en bois munies d'une vis-guide. Celle-ci rend le perçage plus aisé en tirant le foret à l'intérieur de la pièce. Perçage du métal Pour éviter que l’embout ne glisse lorsque vous commencez à percer un trou, faites une encoche à l’aide d’un pointeau et d’un marteau à l’endroit où le trou doit être percé. Placez la pointe de l’embout dans l’encoche et commencez le perçage.
ACCESSOIRES EN OPTION GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo Concreto XPH01 XPH02 13 mm (1/2") 13 mm (1/2") Acero 13 mm (1/2") 13 mm (1/2") Madera 38 mm (1-1/2") 38 mm (1-1/2") Tornillo para madera 10 mm x 89 mm (3/8" x 3-1/2") 6 mm x 75 mm (1/4" x 2-15/16") Tornillo de máquina M6 (1/4") M6 (1/4") Alta (2) 0 - 1 500 r/min 0 - 1 500 r/min Capacidades Velocidad sin carga (r.p.m.
Mantenimiento y uso de la herramienta eléctrica 17. No fuerce la herramienta eléctrica. Utilice la herramienta eléctrica correcta para su aplicación. La herramienta eléctrica adecuada hará un trabajo mejor a la velocidad para la que ha sido fabricada. 18. No utilice la herramienta eléctrica si el interruptor no la enciende y apaga. Cualquier herramienta eléctrica que no pueda ser controlada con el interruptor es peligrosa y debe ser reemplazada. 19.
25. Utilice las herramientas eléctricas solamente con las baterías designadas específicamente para ellas. La utilización de cualquier otra batería puede crear un riesgo de heridas o incendio. 26. Cuando no se esté usando el cartucho de la batería, manténgalo alejado de otros objetos metálicos, como sujetapapeles (clips), monedas, llaves, clavos, tornillos u otros objetos pequeños de metal los cuales pueden actuar creando una conexión entre las terminales de la batería.
ENC007-8 2. INSTRUCCIONES IMPORTANTES DE SEGURIDAD 3. PARA CARTUCHO DE BATERÍA 1. Antes de utilizar el cartucho de batería, lea todas las instrucciones e indicaciones de precaución sobre (1) el cargador de baterías, (2) la batería, y (3) el producto con el que se utiliza la batería. 2. No desarme el cartucho de batería. 3. Si el tiempo de operación se ha acortado en exceso, deje de operar de inmediato. Podría correrse el riesgo de sobrecalentamiento, posibles quemaduras e incluso explosión. 4.
Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección. Este sistema corta en forma automática el suministro de energía a la herramienta para prolongar la vida útil de la batería. La herramienta se detendrá automáticamente durante el funcionamiento si la herramienta y/o la batería se someten a una de las siguientes condiciones: • Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta.
Iluminación de la lámpara delantera Cambio de velocidad 1. Lámpara 1 1. Palanca de cambio de velocidad 1 011503 011495 PRECAUCIÓN: • No mire a la luz ni vea la fuente de luz directamente. Apriete el interruptor de gatillo para encender la lámpara. La lámpara seguirá encendida mientras el gatillo esté siendo apretado. La lámpara se apaga 10-15 segundos después de soltarse el gatillo. PRECAUCIÓN: Ponga siempre la palanca de cambio de velocidad completamente en la posición correcta.
• PRECAUCIÓN: Ponga siempre el anillo correctamente en la marca del modo que desee. Si utiliza la herramienta con el anillo puesto a medias entre las marcas de modo, la herramienta podrá dañarse. Instalación del gancho 1 1. Ranura 2. Gancho 3. Tornillo Ajuste de la torsión de apriete 1 2 3 1. Anillo de cambio del modo de acción 2. Anillo de ajuste 3. Graduación 4. Flecha 2 El gancho resulta útil para colgar temporalmente la herramienta.
Ponga la punta de atornillar sobre la cabeza del tornillo y aplique presión en la herramienta. Haga funcionar la herramienta despacio y después aumente la velocidad gradualmente. Suelte el gatillo interruptor en cuanto el embrague patine.
Taladrado en Madera Cuando taladre en madera, los mejores resultados se obtendrán con brocas para madera equipadas con un tornillo guía. El tornillo guía facilita el taladrado tirando de la broca hacia el interior de la pieza de trabajo. Taladrado en metal Para evitar que la broca resbale al comenzar a hacer un orificio, haga una cavidad con un martillo de golpe central sobre el punto a ser taladrado. Coloque la punta de la broca en la cavidad y comience a taladrar.
ACCESORIOS OPCIONALES GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México PRECAUCIÓN: Estos accesorios o acoplamientos están recomendados para utilizarse con su herramienta Makita especificada en este manual. El empleo de cualquier otro accesorio o aditamento puede conllevar el riesgo de lesiones personales. Use los accesorios o aditamentos sólo para los propósitos para los que fueron diseñados.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Impact Driver Tournevis à Chocs sans Fil Atornillador de Impacto Inalámbrico XDT11 IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: Fastening capacities XDT11 Machine screw 4 mm - 8 mm (5/32" - 5/16") Standard bolt 5 mm - 16 mm (3/16" - 5/8") High tensile bolt 5 mm - 12 mm (3/16" - 1/2") No load speed (RPM) 0 - 2,900 /min Impacts per minute 0 - 3,500 /min Overall length 137 mm (5-3/8") Rated voltage Standard battery cartridge D.C. 18 V BL1815, BL1815N, BL1820, BL1820B BL1830, BL1840, BL1850, BL1840B, BL1850B 1.3 kg (2.8 lbs) 1.5 kg (3.
Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3.
Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery. Switch action Indicating the remaining battery capacity Only for battery cartridges with "B" at the end of the model number 1 1 1. Switch trigger 2 1. Indicator lamps 2. Check button Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds.
Reversing switch action 1 A 2 B 1 1. Driver bit 2. Sleeve To install the driver bit, insert it into the sleeve as far as it will go. 1. Reversing switch lever CAUTION: Always check the direction of rotation before operation. CAUTION: Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. CAUTION: When not operating the tool, always set the reversing switch lever to the neutral position.
The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on to start operation.
Replacing carbon brushes 1 1 1. Carbon brush cap 4. Make sure to place the lead wire in opposite side of the arm. 1. Limit mark Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. All carbon brushes should be replaced at the same time. Use only identical carbon brushes. 2 1. Use a screwdriver to remove two screws then remove the rear cover. 1 1 1. Lead wire 2. Carbon brush cap 5.
be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. implied warranty lasts, so the above limitation may not apply to you. OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle : Capacités de serrage XDT11 Vis de mécanique 4 mm - 8 mm (5/32" - 5/16") Boulon standard 5 mm - 16 mm (3/16" - 5/8") Boulon à haute résistance 5 mm - 12 mm (3/16" - 1/2") Vitesse à vide (T/MIN) 0 - 2 900 /min Percussions par minute 0 - 3 500 /min Longueur totale 137 mm (5-3/8") Tension nominale Batterie standard Poids net • • • C.C.
Évitez les démarrages accidentels. Assurezvous que l’interrupteur est en position d’arrêt avant de brancher l’outil à la prise de courant et/ou au bloc-piles, et avant de prendre ou de transporter l’outil. Vous ouvrez la porte aux accidents si vous transportez les outils électriques avec le doigt sur l’interrupteur ou si vous les branchez alors que l’interrupteur est en position de marche. 4. Retirez toute clé de réglage ou de serrage avant de mettre l’outil électrique sous tension.
6. être extrêmement chauds et vous brûler la peau. Gardez les mains éloignées des pièces en rotation. CONSERVEZ CES INSTRUCTIONS. MISE EN GARDE : NE vous laissez PAS tromper (au fil d’une utilisation répétée) par un sentiment d’aisance ou de familiarité avec le produit en négligeant les consignes de sécurité qui accompagnent le produit. UNE UTILISATION INCORRECTE ou le non-respect des règles de sécurité énoncées dans le présent manuel d’instructions peut provoquer des blessures graves.
Dans cette situation, libérez la gâchette et arrêtez l’activité qui entraîne une surcharge de l’outil. Ensuite, appuyez de nouveau sur la gâchette pour redémarrer. Si l’outil ne démarre pas, la batterie est en surchauffe. Dans cette situation, laissez refroidir la batterie avant d’appuyer de nouveau sur la gâchette. Tension de la batterie faible : La charge restante de la batterie est trop faible pour que l’outil puisse fonctionner. Dans cette situation, retirez et rechargez la batterie. 1 2 3 1.
Interrupteur Fonctionnement de l’inverseur A B 1 1 1. Gâchette ATTENTION : Avant d’insérer la batterie dans l’outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d’arrêt lorsque libérée. Pour mettre l’outil en marche, appuyez simplement sur la gâchette. La vitesse de l’outil augmente à mesure que l’on accroît la pression exercée sur la gâchette. Pour arrêter l’outil, libérez la gâchette. Allumage de la lampe avant 1.
Utilisez uniquement l’embout-tournevis ou l’embout-douille indiqué sur la figure. N’utilisez aucun autre embout-tournevis ou embout-douille. Installation du crochet 1 1 2 2 3 1. Embout-tournevis 2. Manchon Pour installer l’embout-tournevis, insérez-le à fond dans le manchon. 1. Rainure 2. Crochet 3. Vis L’outil est équipé d’un crochet pratique qui permet de le suspendre temporairement. Il s’installe d’un côté comme de l’autre de l’outil.
1. M14(9/16") M16(5/8") M12(1/2") M14(9/16") 60 (43) 40 (29) 20 (14) M10(3/8") M12(1/2") M8(5/16") 0 1,0 2,0 Temps de serrage (s) Couple de serrage Boulon à haute résistance N•m (ft•lbs) 160 (116) 140 (101) 120 (87) 100 (72) 80 (58) M8(5/16") 60 (43) 40 (29) 20 (14) 0 M10(3/8") M8(6/16") 1,0 2. Couple de serrage adéquat 80 (58) M16(5/8") 3,0 3. 4. 5.
2 1 1 2 1. Couvercle arrière 2. Vis 1. Fil de sortie 2. Capuchon de charbon 2. Soulevez le bras du ressort puis placez-le dans la partie creuse du boîtier à l’aide d’un tournevis à pointe plate et tige mince, ou d’un outil similaire. 5. Assurez-vous que les capuchons de charbon sont bien verrouillés dans les orifices des porte-charbons. 1 1 2 2 3 1. Orifice 1. Partie creuse 2. Ressort 3. Bras 3. Utilisez une paire de pinces pour retirer les capuchons de charbon.
Si vous désirez obtenir plus de détails sur ces accessoires, veuillez contacter le centre de service aprèsvente Makita le plus près. • Embouts-tournevis • Crochet • Mallette de transport en plastique • Chargeur et batterie authentiques Makita • Protecteur de batterie NOTE : Certains éléments de la liste peuvent être inclus avec l’outil comme accessoires standards. Ils peuvent varier suivant les pays.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: Capacidades de apriete XDT11 Tornillo de máquina 4 mm - 8 mm (5/32" - 5/16") Tornillo estándar 5 mm - 16 mm (3/16" - 5/8") Tornillo de alta resistencia 5 mm - 12 mm (3/16" - 1/2") Velocidad sin carga (rpm) 0 - 2 900 r/min Impactos por minuto 0 - 3 500 ipm Longitud total 137 mm (5-3/8") Tensión nominal Cartucho de batería estándar Peso neto • • • 18 V c.c.
zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. 3. Impida el encendido accidental. Asegúrese de que el interruptor esté en la posición de apagado antes de conectar a la alimentación eléctrica y/o de colocar el cartucho de batería, así como al levantar o cargar la herramienta.
6. extremadamente calientes y provocarle una quemadura. Mantenga las manos alejadas de las piezas giratorias. GUARDE ESTAS INSTRUCCIONES. ADVERTENCIA: NO DEJE que la comodidad o familiaridad con el producto (a base de utilizarlo repetidamente) evite que siga estrictamente las normas de seguridad para dicho producto. El USO INCORRECTO o el no seguir las normas de seguridad indicadas en este manual de instrucciones puede ocasionar lesiones graves.
1 2 3 1. Indicador rojo 2. Botón 3. Cartucho de batería Para quitar el cartucho de batería, deslícelo de la herramienta mientras desliza el botón sobre la parte delantera del cartucho. Para colocar el cartucho de batería, alinee la lengüeta sobre el cartucho de batería con la ranura en la carcasa y deslice en su lugar. Inserte por completo hasta que se fije en su lugar con un pequeño clic. Si puede ver el indicador rojo del lado superior del botón, esto indica que no ha quedado fijo por completo.
NOTA: Dependiendo de las condiciones de uso y la temperatura ambiente, la indicación podrá diferir ligeramente de la capacidad real. Accionamiento del interruptor de inversión Accionamiento del interruptor A B 1 1 1. Gatillo interruptor PRECAUCIÓN: Antes de insertar el cartucho de batería en la herramienta, compruebe siempre y cerciórese de que el gatillo interruptor se acciona debidamente y que vuelve a la posición “OFF” (apagado) cuando lo suelta.
Instalación o extracción de la punta de destornillador/punta de atornillar 12 mm (15/32”) 9 mm (3/8”) NOTA: Si la punta de destornillador no se encuentra insertada hasta el fondo en el mandril, éste no regresará a su posición original y la punta de destornillador no quedará asegurada. En este caso, procure insertar la broca de nuevo siguiendo las instrucciones de arriba. NOTA: Si tiene dificultades para insertar la punta de destornillador, jale el mandril e inserte la broca tanto como sea posible.
1. 100 N•m (72 ft•lbs) 80 N•m (58 ft•lbs) 16 mm(5/8") 14 mm(9/16") 2. Torsión de apriete adecuada Torsión de apriete Tornillo estándar N•m (ft•lbs) 140 N•m (101 ft•lbs) 120 N•m (87 ft•lbs) 16 mm(5/8") 12 mm(1/2") 14 mm(9/16") 60 N•m (43 ft•lbs) 10 mm(3/8") 40 N•m (29 ft•lbs) 20 N•m (14 ft•lbs) 12 mm(1/2") 8 mm(5/16") 0 1,0 s 10 mm(3/8") 8 mm(6/16") 2,0 s 3,0 s 4. Tiempo de apriete (s) 1,0 s 2,0 s 5.
2 1 1 2 1. Cubierta posterior 2. Tornillo 1. Cable conductor 2. Tapa de las escobillas de carbón 2. Levante la parte del brazo del resorte y después póngalo en la parte empotrada del alojamiento con un destornillador de punta plana de eje largo y fino o similar. 5. Asegúrese de que las tapas de las escobillas de carbón hayan encajado en forma segura en los orificios de los portaescobillas. 1 2 1 2 3 1. Parte empotrada 2. Resorte 3. Brazo 1. Orificio 3.
ACCESORIOS OPCIONALES consecuentes, por lo que la limitación o exclusión arriba mencionada podría no aplicar para usted. Algunos estados no permiten la limitación sobre la duración de una garantía implícita, por lo que la limitación arriba mencionada podría no aplicar para usted. PRECAUCIÓN: Estos accesorios o aditamentos están recomendados para utilizarse con su herramienta Makita especificada en este manual.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES Cordless Circular Saw Scie Circulaire sans Fil Sierra Circular Inalámbrica XSS01 XSS02 006699 IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model XSS01 Blade diameter Max. Cutting depth XSS02 165 mm (6-1/2") at 90° 57 mm (2-1/4") at 45° 40 mm (1-9/16") at 50° 36 mm (1-7/16") No load speed (RPM) 3,700 /min Overall length 347 mm (13-5/8") Net weight 3.2 kg (7.1 lbs) Rated voltage 3.5 kg (7.6 lbs) 3.1 kg (6.8 lbs) 3.3 kg (7.3 lbs) D.C.
26. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 27. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
12. 5. Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and could give the operator an electric shock. 6. When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding. 7. Always use blades with correct size and shape (diamond versus round) of arbour holes.
Additional safety warnings 23. Intended use This tool is intended to cut wood products only. Accumulated sawdust on the lower guard and hub from other materials may effect the proper closure of the lower guard which could lead to serious personal injury. 24. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing knots. Maintain smooth advancement of tool without decrease in blade speed to avoid overheating the blade tips. 25.
ENC007-8 IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4.
Battery protection system (Lithium-ion battery with star marking) FUNCTIONAL DESCRIPTION • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 1. Star marking 1 Installing or removing battery cartridge 1 2 1. Red indicator 2. Button 3. Battery cartridge 012128 Lithium-ion batteries with a star marking are equipped with a protection system.
Bevel cutting Switch action 1. Lever 1 2 1. Switch trigger 2. Lock-off lever 1 006702 006705 For Model XSS01 CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. • Do not pull the switch trigger hard without pressing the lock-off lever. This can cause switch breakage. To prevent the switch trigger from being accidentally pulled, a lock-off lever is provided.
NOTE: • Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. • Do not use gasoline, thinner or the like to clean the lens of lamp. Using such substances will damage the lens. Hex wrench storage 1. Hex wrench 1 ASSEMBLY • CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.
• If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. 1 2 MAINTENANCE 1. Rear handle 2. Front grip 3. Base • • 3 006709 Hold the tool firmly. The tool is provided with both a front grip and rear handle. Use both to best grasp the tool. If both hands are holding saw, they cannot be cut by the blade. Set the base on the workpiece to be cut without the blade making any contact.
Replacing carbon brushes Combination 1. Limit mark General purpose blade for fast and smooth rip, crosscuts and miters. 006540 • • • • Rip fence (Guide rule) Hex wrench 5 Dust nozzle Makita genuine battery and charger 1 NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country. 001145 Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
FRANÇAIS (Mode d’emploi original) SPÉCIFICATIONS Modèle XSS01 Diamètre de la lame Profondeur de coupe max. XSS02 165 mm (6-1/2") à 90° 57 mm (2-1/4") à 45° 40 mm (1-9/16") à 50° 36 mm (1-7/16") Vitesse à vide (T/MIN) 3 700 /min Longueur totale 347 mm (13-5/8") Poids net 3,2 kg (7,1 lbs) Tension nominale 3,5 kg (7,6 lbs) 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) C.C.
Sécurité personnelle 10. Restez alerte, attentif à vos mouvements et faites preuve de bon sens lorsque vous utilisez un outil électrique. Évitez d'utiliser un outil électrique si vous êtes fatigué ou si vous avez pris une drogue, de l'alcool ou un médicament. Un moment d'inattention pendant l'utilisation d'un outil électrique peut entraîner une grave blessure. 11. Portez des dispositifs de protection personnelle. Portez toujours un protecteur pour la vue.
contact avec un conducteur sous tension, les pièces métalliques à découvert de l'outil deviendraient également sous tension et risqueraient de transmettre une décharge à l'utilisateur. 6. Lors du sciage en long, utilisez toujours un garde parallèle ou un guide de coupe rectiligne. Cela améliore la précision de la coupe et réduit le risque de coincement de la lame. 7. Employez toujours une lame de diamètre approprié et dont le trou central est de forme correcte (angulaire ou ronde).
15. la cause du coincement de la lame et prenez les mesures correctives pour éliminer le problème. 11. Avant de faire redémarrer la scie dans la pièce, centrez la lame dans le trait de scie et assurez-vous que les dents de la lame ne mordent pas déjà dans le matériau. Si la lame est coincée, elle risque de remonter dans le trait de scie ou de causer un recul au moment du redémarrage de la scie. 12.
rappel et libérez le protecteur inférieur dès que la lame pénètre dans le matériau. Pour toute autre opération de sciage, le protecteur inférieur devrait fonctionner automatiquement. 21. Assurez-vous toujours que le protecteur inférieur couvre bien la lame avant de déposer l'outil sur l'établi ou sur le sol. Si la lame n'est pas protégée et n'a pas fini de tourner, elle entraînera la scie vers l'arrière en coupant tout sur son passage.
31. 32. 33. 34. 35. N'appliquez jamais une pression latérale sur la lame pour l'arrêter. N'utilisez aucune meule abrasive. N'utilisez que la lame dont le diamètre correspond aux indications données sur l’outil ou dans le manuel. L’utilisation d’une lame d’une taille incorrecte peut affecter la protection de la lame ou le fonctionnement du protecteur et cela pourrait causer de graves blessures. Maintenez la lame affûtée et propre.
Système de protection de la batterie (batterie lithium-ion marquée d’une étoile) DESCRIPTION DU FONCTIONNEMENT 1. Étoile 1 • ATTENTION: Assurez-vous toujours que l'outil est hors tension et que sa batterie est retirée avant de l'ajuster ou de vérifier son fonctionnement. Installation ou retrait de la batterie 1 2 1. Indicateur rouge 2. Bouton 3. Batterie 012128 Les batteries lithium-ion marquées d’une étoile sont équipées d’un système de protection.
d'une dent de lame ne dépasse sous la pièce. L'utilisation d'une profondeur de coupe adéquate aide à réduire les risques de chocs en retour dangereux qui peuvent causer des blessures. Interrupteur 1 2 Coupe en biseau 1. Gâchette 2. Levier de sécurité 1. Levier 006705 ATTENTION: Avant d'insérer la batterie dans l'outil, vérifiez toujours que la gâchette fonctionne bien et revient en position d'arrêt lorsque relâchée.
Pour allumer la lumière sans faire démarrer l'outil, appuyez sur la gâchette sans appuyer sur le levier de déverrouillage. Pour allumer la lumière et faire démarrer l'outil, appuyez sur le levier de déverrouillage et appuyez sur la gâchette alors que le levier de verrouillage est enfoncé. 1. Bague interne 2. Lame 3. Bague externe 4. Boulon hexagonal 2 4 3 NOTE: • Utilisez un chiffon sec pour essuyer la saleté qui recouvre la lentille de la lampe.
Garde parallèle (règle de guidage) UTILISATION • • • 1. Vis de serrage 2. Garde parallèle (règle de guidage) ATTENTION: Insérez toujours la batterie jusqu'au fond, jusqu'à ce qu'elle verrouille en place. Si vous pouvez voir la partie rouge de la face supérieure du bouton, la batterie n'est pas parfaitement verrouillée. Insérez-la à fond, jusqu'à ce que la partie rouge ne soit plus visible.
demande de réparation auprès du centre de service après-vente Makita le plus près. Réglage de précision pour la coupe à 90° (coupe verticale) Pour le modèle XSS02 Ce réglage est réalisé en usine. S'il se défait, ajustez la vis de réglage au moyen d'une clé hexagonale tout en mesurant l'angle de 90° de la lame par rapport à la base à l'aide d'une règle triangulaire, d'une équerre, etc. 2 1 1 2 1. Réglage de la vis à 45 ゚ (XSS01 seulement) 2.
GARANTIE LIMITÉE D’UN AN MAKITA Politique de garantie Chaque outil Makita est inspecté rigoureusement et testé avant sa sortie d’usine. Nous garantissons qu’il sera exempt de défaut de fabrication et de vice de matériau pour une période d’UN AN à partir de la date de son achat initial. Si un problème quelconque devait survenir au cours de cette période d’un an, veuillez retourner l’outil COMPLET, port payé, à une usine ou à un centre de service après-vente Makita.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo XSS01 Diámetro del disco Profundidad de corte máxima XSS02 165 mm (6-1/2") a 90° 57 mm (2-1/4") a 45° 40 mm (1-9/16") a 50° 36 mm (1-7/16") Velocidad sin carga (r.p.m.) 3 700 r/min Longitud total 347 mm (13-5/8") Peso neto 3,2 kg (7,1 lbs) 3,5 kg (7,6 lbs) Tensión nominal 3,1 kg (6,8 lbs) 3,3 kg (7,3 lbs) 18 V c.c.
19. Desconecte la clavija de la fuente de energía y/o la batería de la herramienta eléctrica antes de realizar ajustes, cambiar accesorios o guardar las herramientas eléctricas. Dichas medidas de seguridad preventivas reducen el riesgo de que la herramienta se inicie accidentalmente. 20. Guarde la herramienta eléctrica que no use fuera del alcance de los niños y no permita que las personas que no están familiarizadas con ella o con las instrucciones la operen.
27. En condiciones abusivas, podrá escapar líquido de la batería; evite tocarlo. Si lo toca accidentalmente, enjuague con agua. Si hay contacto del líquido con los ojos, acuda por ayuda médica. Puede que el líquido expulsado de la batería cause irritación o quemaduras. Servicio de mantenimiento 28. Haga que una persona calificada repare la herramienta utilizando sólo piezas de repuesto idénticas. Esto asegura que se mantenga la seguridad de la herramienta eléctrica. 29.
11. 12. inmóvil en el material hasta que el disco se pare completamente. No intente nunca extraer el disco de la pieza de trabajo ni tirar de la sierra hacia atrás mientras el disco esté moviéndose porque podrá ocasionar un retroceso brusco. Investigue y tome medidas correctivas para eliminar la causa del atoramiento del disco. Cuando vuelva a poner en marcha la sierra sobre la pieza de trabajo, centre la sierra en la entalladura y compruebe que sus dientes no estén en contacto con el material.
especiales como “cortes de cavidad” y “cortes compuestos.” Levante el protector inferior mediante el mango retráctil y cuando el disco entre en el material, debe soltar el protector inferior. Para todos los otros cortes con sierra, el protector inferior debe funcionar automáticamente. 21. Antes de dejar la sierra en el banco o en el suelo, observe siempre que el protector inferior esté cubriendo el disco.
31. 32. 33. 34. 35. No detenga el disco de la sierra mediante presión lateral sobre el mismo. No use ningún disco abrasivo. Use solamente un disco de sierra cuyo diámetro esté marcado en la herramienta o especificado en el manual. El uso de un disco de sierra de tamaño inadecuado puede que afecte la protección del disco o del protector en sí, lo cual podría resultar en graves lesiones al operador. Mantenga el disco afilado y limpio.
Sistema de protección de batería (batería de ión de litio con marca de estrella) DESCRIPCIÓN DEL FUNCIONAMIENTO 1. Marca de estrella 1 • PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de realizar cualquier ajuste o comprobación en la herramienta. Instalación o desmontaje del cartucho de batería 1 2 012128 Las baterías de ión de litio con una marca de estrella están equipadas con un sistema de protección.
Afloje la palanca del lateral del mango posterior y mueva la base hacia arriba o hacia abajo. Cuando haya alcanzado la profundidad de corte deseada, fije la base apretando la palanca. Para obtener cortes más limpios y seguros, ajuste la profundidad de corte de forma que no sobresalga más de un diente del disco de sierra por debajo de la pieza de trabajo.
Utilice solamente la llave Makita para instalar o desmontar el disco. Para quitar el disco, presione el bloqueo del eje de forma que el disco no pueda girar y afloje el perno hexagonal girándolo en sentido de las agujas del reloj con la llave. Después quite el perno hexagonal, la brida exterior y el disco. Para instalar el disco, siga el procedimiento de desmontaje a la inversa. ASEGÚRESE DE APRETAR EL PERNO HEXAGONAL EN SENTIDO CONTRARIO A LAS AGUJAS DEL RELOJ FIRMEMENTE.
velocidad. Ahora simplemente mueva la herramienta hacia delante sobre la superficie de la pieza de trabajo, manteniéndola plana y avanzando suavemente hasta completar el corte. Para obtener cortes limpios, mantenga la línea de corte recta y la velocidad de avance uniforme. Si se desvía de la línea de corte prevista, no intente girar ni forzar la herramienta para hacerla volver a la línea de corte. Esta acción podría inmovilizar el disco y ocasionar un peligroso retroceso brusco y posibles heridas graves.
Utilice un destornillador para quitar las tapas de los portaescobillas. Extraiga las escobillas gastadas, inserte las nuevas y vuelva a colocar las tapas. Para modelo XSS01 Después de reemplazar las escobillas, inserte el cartucho de batería en la herramienta y hágale el rodaje a las escobillas haciendo funcionar la herramienta sin carga durante 1 minuto aproximadamente. Después compruebe la herramienta mientras está en marcha y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA MAKITA DE UN AÑO Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de fábrica. Se garantiza que va a estar libre de defectos de mano de obra y materiales por el periodo de UN AÑO a partir de la fecha de adquisición original.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES Cordless Recipro Saw Sierra Recíproca Inalámbrica XRJ04 IMPORTANT: Read Before Using. IMPORTANTE: Lea antes de usar.
ENGLISH (Original instructions) SPECIFICATIONS Model: XRJ04 Length of stroke 32 mm (1-1/4″) Strokes per minute Max. cutting capacities 0 - 2,800 /min Pipe 130 mm (5-1/8″) Wood 255 mm (10″) Rated voltage D.C. 18 V Standard battery cartridge BL1815N, BL1820, BL1820B Overall length 486 mm (19-1/8″) Net weight • • • BL1830, BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B 3.5 kg (7.6 lbs) 3.8 kg (8.
7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 2. 3. Power tool use and care 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off.
Symbols CAUTION: Only use genuine Makita batteries. Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger. The followings show the symbols used for tool. volts direct current Tips for maintaining maximum battery life no load speed 1. revolutions or reciprocation per minute 2. Important safety instructions for battery cartridge 1. 2. 3.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. Indicating the remaining battery capacity To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
1 1 2 B A 2 ► 1 . Lock-off button 2. Switch trigger 3 ► 1 . Blade clamp lever 2. Released position 3. Fixed position To prevent the switch trigger from accidentally pulled, the lock-off button is provided. To start the tool, depress the lock-off button from B side and pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop. After use, always press in the lock-off button from A side.
MAINTENANCE CAUTION: Keep hands and fingers away from the lever during the switching operation. Failure to do so may cause personal injuries. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. NOTE: If you remove the recipro saw blade without rotating the blade clamp lever fully, the lever may not be locked in the released position .
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ESPAÑOL (Instrucciones originales) ESPECIFICACIONES Modelo: XRJ04 Extensión de la carrera 32 mm (1-1/4″) Carreras por minuto Capacidad máxima de corte 0 - 2 800 cpm Tubo 130 mm (5-1/8″) Madera 255 mm (10″) Tensión nominal 18 V c.c.
2. 3. 4. 5. 6. 7. Use equipo de protección personal. Póngase siempre protección para los ojos. El equipo protector tal como máscara contra el polvo, zapatos de seguridad antiderrapantes, casco rígido y protección para oídos utilizado en las condiciones apropiadas reducirá el riesgo de lesiones. Impida el encendido accidental.
3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Use siempre gafas de seguridad o protectoras. Los anteojos comunes o para el sol NO son gafas de seguridad. Evite cortar clavos. Revise la pieza de trabajo y quite todos los clavos antes de utilizar la herramienta. No corte piezas de trabajo demasiado grandes. Compruebe que hay espacio suficiente más allá de la pieza de trabajo antes de cortar para que el disco no golpee el suelo, el banco de trabajo, etc. Sujete la herramienta con firmeza.
PRECAUCIÓN: Utilice únicamente baterías originales de Makita. El uso de baterías no originales de Makita, o de baterías alteradas, puede ocasionar que las baterías exploten causando un incendio, lesiones personales y daños. Asimismo, esto invalidará la garantía de Makita para la herramienta y el cargador Makita. 1 2 Consejos para alargar al máximo la vida útil de la batería 1. 2. 3. 4. Cargue el cartucho de batería antes de que se descargue completamente.
Sobrecarga: La herramienta se está utilizando de una manera que causa que consuma una cantidad de corriente inusualmente alta. En este caso, apague la herramienta y detenga la aplicación que causó que la herramienta se sobrecargara. Luego encienda la herramienta para reiniciarla. Si la herramienta no arranca, significa que la batería se sobrecalentó. En este caso, espere a que la batería se enfríe antes de volver a encender la herramienta.
Para instalar la segueta recíproca, asegúrese siempre de que la palanca de la abrazadera de la segueta (parte del manguito de la abrazadera de la segueta) esté en en la cubierta de aislamiento la posición liberada antes de insertar la segueta recíproca. Si la palanca de la abrazadera de la segueta se encuentra en la posición fija, gírela en la dirección de la flecha para que pueda ser trabada en la posición liberada . 2 1 1 ► 1 . Segueta recíproca 2.
1 ► 1 . Tapa del portaescobillas MANTENIMIENTO PRECAUCIÓN: Asegúrese siempre de que la herramienta esté apagada y el cartucho de batería extraído antes de intentar realizar una inspección o mantenimiento. 3. Inserte el cartucho de batería en la herramienta y haga el rodaje de las escobillas poniendo a funcionar la herramienta sin carga durante 1 minuto aproximadamente. 4. Revise la herramienta mientras está funcionando y la operación del freno eléctrico cuando suelte el gatillo interruptor.
GARANTÍA LIMITADA DE UN AÑO DE MAKITA Ésta Garantía no aplica para México Política de garantía Cada herramienta Makita es inspeccionada y probada exhaustivamente antes de salir de la fábrica. Se garantiza que está libre de defectos de mano de obra y materiales por el período de UN AÑO a partir de la fecha original de compra. Si durante este período de un año se desarrollara algún problema, devuelva la herramienta COMPLETA, con el envío prepagado, a un centro de servicio autorizado o de fábrica Makita.
17
18
19
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
INSTRUCTION MANUAL Cordless Angle Grinder XAG03 XAG04 015078 IMPORTANT: Read Before Using.
ENGLISH (Original instructions) SPECIFICATIONS Model XAG03 XAG04 Wheel diameter 115 mm (4-1/2") 125 mm (5") Max. wheel thickness 6 mm (1/4") Spindle thread Rated speed (n) / No load speed (n0) Overall length Net weight 6 mm (1/4") 5/8" 8,500 /min With battery cartridge BL1815N, BL1820 348 mm (13-3/4") With battery cartridge BL1830, BL1840, BL1850 362 mm (14-1/4") With battery cartridge BL1815N, BL1820 2.3 kg (5.0 lbs) With battery cartridge BL1830, BL1840, BL1850 2.5 kg (5.5 lbs) 2.
Battery tool use and care 24. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 25. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 26.
5. 6. 7. 8. 9. 10. 11. 12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 13. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. 14. Do not operate the power tool near flammable materials. Sparks could ignite these materials. 15.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. ENC007-8 Do not leave the tool running. Operate the tool only when hand-held. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care. Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels. Use only flanges specified for this tool.
FUNCTIONAL DESCRIPTION • 1. Slide switch 1 CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing or removing battery cartridge 015082 1. Button 2. Red indicator 3. Battery cartridge 1 To start the tool, slide the slide switch toward the "I (ON)" position by pushing the rear of the slide switch. For continuous operation, press the front of the slide switch to lock it.
Releasing protection lock When the protection system works repeatedly, the tool is locked and the battery indicator shows the following state. Automatic speed change function 1. Mode indicator 1 Battery indicator On Off Blinking Protection lock works 015200 In this situation, the tool does not start even if turning the tool off and on. To release the protection lock, remove the battery, set it to the battery charger and wait until the charging finishes.
For tool with locking screw type wheel guard Installing or removing wheel guard (For depressed center wheel, multi disc / abrasive cut-off wheel, diamond wheel) 1. Wheel guard 2. Bearing box 3. Screw WARNING: When using a depressed center grinding wheel/Multi-disc, wire wheel brush, cut-off wheel or diamond wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
Grinding and sanding operation Installing or removing abrasive disc (optional accessory) 1 2 1. Sanding lock nut 2. Abrasive disc 3. Rubber pad 3 A B 015097 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.
Operation with abrasive cut-off / diamond wheel (optional accessory) 1. Lock nut 2. Abrasive cut-off wheel/diamond wheel 3. Inner flange 4. Wheel guard for abrasive cut-off wheel/diamond wheel 1 2 3 4 010855 Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Mount the inner flange and abrasive cut-off / diamond wheel onto the spindle. Tighten the lock nut securely with supplied wrench.
Remove the battery cartridge from the tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pressure which causes over bending of wires, leading to premature breakage.
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. • Your tool is supplied with a guard for use with a depressed center grinding wheel, multi-disc and wire wheel brush.
1 6 2 3 7 4 8 2 11 10 9 3 12 5 5 115 mm (4-1/2") model 2 3 125 mm (5") model Grip 36 Wheel Guard (for grinding wheel) 1 Inner flange 45 Inner flange 45 4 Depressed center wheel/Multi-disc 5 Lock nut 5/8-45 Lock nut 5/8-45 6 Rubber pad 100 Rubber pad 115 7 8 Abrasive disc Sanding lock nut 5/8-48 9 Sanding lock nut 5/8-48 Wire wheel brush 10 Wire cup brush 11 Wheel Guard (for cut-off wheel) 12 - Abrasive cut-off wheel/Diamond wheel Lock nut wrench 28 Lock nut wrench 28 0153
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
< USA only > WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.
GB Rechargeable Flashlight Instruction manual F Lampe torche Manuel d’instructions E Linterna recargable Manual de instrucciones DML145/DML185
3 2 4 1 1 2 5 6 3 4 7 5 2
Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning be-fore use. Symboles Les symboles utilisés pour l’appareil sont indiqués ci-dessous. Assurez-vous d’avoir bien compris leur signification avant l’utilisation. Símbolos Se utilizan los siguientes símbolos para el equipo. Asegúrese de que comprende su significado antes del uso. ❏ Read instruction manual. ❏ Veuillez lire le manuel d’instructions. ❏ Lea el manual de instrucciones.
ENGLISH Explanation of general view 1. 2. 3. 4. 5. 6. Battery cartridge Button Red part 7. Switch Ring Bulb Shoulder strap SPECIFICATIONS Model DML145 DML185 Bulb 12 V 0.7 A 18 V 0.6 A Dimensions (without battery) Net weight (with battery) L 284 mm (11 - 1/8”) 284 mm (11 - 1/8”) W 84 mm (3 - 5/16”) 84 mm (3 - 5/16”) H 96 mm (3 - 3/4”) 96 mm (3 - 3/4”) BL1415/BL1415N 0.66 kg (1.44 lbs) BL1430/BL1440 0.85 kg (1.87 lbs) BL1815/BL1815N/BL1820 0.71 kg (1.57 lbs) BL1830/BL1840 0.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. • Do not use force when inserting the battery cartridge.
FRANÇAIS Descriptif 1. 2. 3. 4. 5. 6. Batterie Bouton Partie rouge 7.
DESCRIPTION DU FONCTIONNEMENT Angle de tête (Fig. 2) L’angle de tête peut être réglé sur l’une ou l’autre de quatre positions. Réglez-le selon vos besoins. Charge Avant l’utilisation, chargez la batterie avec le chargeur Makita. Installation et retrait de la batterie (Fig.1) • Mettez toujours l’outil hors tension avant d’insérer ou de retirer la batterie. • Pour retirer la batterie, sortez-la de l’outil tout en faisant glisser le bouton à l’avant de la batterie.
ESPAÑOL Explicación de los dibujos 1. 2. 3. 4. 5. 6. Cartucho de la batería Botón Parte roja 7.
DESCRIPCIÓN DEL FUNCIONAMIENTO Ángulo de la cabeza (Fig. 2) El ángulo de la cabeza se puede ajustar en cuatro posiciones. Ajústelo como desee. Carga Cargue el cartucho de la batería con el cargador de Makita antes de su uso. Instalación o extracción del cartucho de la batería (Fig. 1) • Apague siempre la herramienta antes de insertar o extraer el cartucho de la batería.
10
11
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885246-944 ALA www.makita.
GB Radio Instruction manual F Radio Manuel d’instructions E Radio Manual de instrucciones XRM02
12 10 2 3 14 1 4 5 6 7 8 9 13 L K A B C 20 J PM I D H E G F 11 1 2
14 15 15 15 16 11 2 3 17 18 19 21 4 5 19 19 6 7 3
19 19 8 9 10 10 10 11 8 9 12 4
ENGLISH (Original instructions) IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: 1. Read this instruction manual and the charger instruction manual carefully before use. 2. Clean only with dry cloth. 3. Do not block any ventilation opening. Install in accordance with the manufacturer’s instruction. 4.
• Powered by both Makita battery pack and supplied power adaptor Explanation of general view (Fig. 1) Controls: 1. Power and Sleep timer 2. Band and Mono button 3. Radio alarm set 4. Buzzer alarm set 5. Preset stations 6. Scan tuning and Time set 7. Tuning/Volume control knob 8. DC IN socket 9. Input terminal (AUX IN1) 10. Soft bended rod antenna 11. Battery compartment (covering main battery pack and back up batteries) 12. Handle 13. Speaker 14. Battery compartment locker 15. Main battery compartment 16.
The following tables indicate the operating time on a single charge. Battery Cartridge Voltage 7.2 V 9.6 V 10.8 V 12 V 14.4 V 18 V PA09 PA12 PA14 PA18 9050 1250 1450 1850 9051 1251 1452 1852 9100 1200 1420 BL1815 1220 BL1415 BL7010 AT SPEAKER OUTPUT= 50 mW + 50 mW unit: Hour Approx. 7.0 9120 BL1014 9100A 1200A 9102 1202 1422 BH1420 BL1815N 9122 1222 9102A 1202A BH9020 BH1220 BH9020A BH1200C 9134 1234 Approx. 10.0 1822 Approx. 12.5 1434 1834 BH1427 9135 Approx.
Note: The battery pack can’t be charged via the supplied AC power adaptor. 6. When low battery sign appears and an “E” keeps on flashing is the time to replace the back up batteries. Installing the Soft bended rod antenna (Fig. 10 & 11) Install the Soft bended rod antenna as shown in the figure. Note: There is a click in the battery compartment designed to store the removed antenna. Using Supplied AC power adaptor (Fig.
Recall stations from preset memories 1. Press the Power button to turn on the radio. 2. Select the required waveband. 3. Momentarily press the required Preset button, the preset number and station frequency will appear in the display. Setting the radio alarm When the radio alarm is selected, the radio will turn on and play the chosen radio station at the chosen alarm time. The radio alarm will continue for one hour unless turned off by pressing the Power button.
How to play other audios CAUTION: Unplug this apparatus before connecting other audios. • There are 2 AUX in sockets. AUX 1 is located on the front panel, and AUX 2 is located in the battery compartment. • Connect a stereo or mono source (i.e. iPod, MP3, or CD player) to either AUX 1 or AUX 2 by audio cord. • Repeatedly press and release the Band button until “AU1” or “AU2” is displayed, then AUX function is activated. • AUX can’t be activated as alarm source.
FRANÇAIS (Mode d’emploi original) CONSIGNES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT : Lors de l’utilisation d’outils électriques, il faut toujours prendre des précautions élémentaires de sécurité, dont les suivantes, pour réduire les risques d’incendie, de décharge électrique et de blessure. 1. Lisez attentivement ce manuel d’instructions et celui du chargeur avant l’utilisation. 2. Nettoyez uniquement avec un chiffon sec. 3. Ne bloquez aucun orifice de ventilation.
Caractéristiques : • • • • • • • • • • • Synthétiseur PLL AM/FM stéréo Écran LCD lumineux Recherche manuelle/présélection/automatique Réglage du son Présélections de 5 radios sur chaque bande Horloge et deux alarmes (radio et buzzer) avec fonction « sieste » Radio réveil (arrêt automatique) Haut-parleur stéréo de haute qualité Design dépouillé Résistance à l’eau - IPX 4 Alimenté par des piles Makita ou l’adaptateur secteur fourni Descriptif (Fig. 1) Contrôles : 1. Mise en marche et fonction de sommeil 2.
Le tableau suivant indique le temps de fonctionnement par charge.
batterie sur l’écran sont les signes qu’il est nécessaire de changer de batteries. Remarque : Les batteries ne peuvent pas être rechargées à l’aide de l’adaptateur secteur fourni. 6. Quand le témoin de charge de la batterie apparaît et qu’un « E » clignote, il est temps de changer les batteries. Installation de l’antenne à tige souple (Fig. 10 et 11) Procéder comme indiqué sur la figure pour installer l’antenne à tige souple.
Stockage des stations de radio en mémoire présélectionnée Il y a 5 mémoires présélectionnées sur chaque bande de fréquence. 1. Appuyer sur le bouton de mise en marche pour activer la radio. 2. Rechercher la station choisie comme décrit précédemment. 3. Appuyer sur le bouton et le maintenir enfoncé jusqu’à ce que la radio émette un bip. La station sélectionnée apparaît sur l’écran, et la station est stockée en mémoire sous le bouton choisi. 4. Répéter l’opération pour les autres présélections. 5.
Relâcher le bouton de mise en marche quand l’heure sélectionnée apparaît à l’écran. Le symbole apparaît à l’écran et la radio se met en marche sur la dernière station sélectionnée. 2. Pour désactiver la fonction de sommeil, appuyer sur le bouton de mise en marche. Le symbole disparaît et la radio est arrêtée. Eclairage de l’écran Appuyer sur n’importe quel bouton ou tourner sur le bouton de commande Réglage/Volume et l’écran LCD s’éclaire pendant environ 15 secondes.
ESPAÑOL (Instrucciones originales) INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA: Cuando utilice herramientas eléctricas, deberá tomar siempre precauciones de seguridad básicas, incluyendo las siguientes, para reducir el riesgo de incendios, descargas eléctricas y heridas personales: 1. Lea este manual de instrucciones y el manual de instrucciones del cargador con cuidado antes de usar. 2. Limpie sólo con un paño limpio. 3. No obstruya ninguna apertura de ventilación.
Para Estados Unidos: Precauciones para el usuario Los cambios o modificaciones que no hayan sido expresamente autorizados por la entidad responsable por el cumplimiento de las regulaciones podrían anular la autoridad del usuario de utilizar este equipo. Este equipo ha sido probado y demuestra que cumple con los límites de un Dispositivo Digital de Clase B, en conformidad con la sección 15 de las regulaciones de la FCC.
La tabla a continuación indica el tiempo de operación en una sola carga. Voltaje del cartucho de batería 7,2 V 9,6 V 10,8 V 12 V 14,4 V 18 V PA09 PA12 PA14 PA18 9050 1250 1450 1850 9051 1251 1452 1852 9100 1200 1420 BL1815 1220 BL1415 BL7010 A NIVEL DE SALIDA DEL ALTAVOZ= 50 mW + 50 mW unidad: Hora Aprox. 7,0 9120 BL1014 9100A 1200A 9102 1202 1422 BH1420 BL1815N 9122 1222 9102A 1202A BH9020 BH1220 BH9020A BH1200C 9134 1234 Aprox. 10,0 1822 Aprox.
de que el paquete de baterías requiere ser reemplazado. Nota: El paquete de baterías no puede recargarse mediante el adaptador del cable eléctrico de CA. 6. Cuando el símbolo de batería baja aparece y una “E” continúa parpadeando, significa que es tiempo de reemplazar las pilas de respaldo. Instalación de la antena plegable de varilla suave (Fig. 10 y 11) Instale la antena plegable de varilla suave como se ilustra en la figura.
4. Continúe girando la perilla de control de sintonía / volumen hasta que haya conseguido mostrar la frecuencia deseada en la pantalla. 5. Gire la perilla de control de sintonía / volumen para conseguir el nivel de sonido deseado. 6. Para apagar la radio, presione el botón encendido. La pantalla mostrará “OFF”. Almacenamiento de estaciones en memorias preajustadas Hay 5 preajustes de memoria para cada banda de frecuencia. 1. Presione el botón de encendido de la radio para encenderla. 2.
presione el botón de ajuste de hora nuevamente para completar el ajuste de la alarma de timbre HWS. 6. Presione y mantenga presionado el botón de la alarma de timbre por más de 2 segundos y enseguida se emitirá un pitido el cual activa o desactiva la alarma de timbre HWS. La pantalla mostrará el símbolo cuando la alarma de timbre esté activa. Función de silenciador temporal 1.
23
Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan XRM02(DMR102)-NA3-0914 ALA www.makita.