Programming Instructions

ManualsBrandsMANARAS/OPERA ManualsElectronicsRemote Control

Rolling Code Transmitters - Series "100"

Specifications and Programming Instructions

Transmitter Programming: RADIOEM144

The RADIOEM144 Rolling Code Transmitter can be used to control up to 144 doors with Open / Close / Stop function.

Two rotary dials (Letters: A to L) and (Numbers: 1 to 12) permit for a proper door selection. The Transmitter can be re-

programmed as needs change.

Transmitter Modes and Functions Transmitter Programming

RADIOEM144

Multiple Door (up to144 doors)

3-Button Transmitter

1.OPEN  Top Button

2.CLOSE  Middle Button

3.STOP  Bottom Button

No initial programming is required.

This Transmitter is ready to be matched to the

Receiver of your choice, refer to section Transmitter

to Operator Matching (Pairing), p. 3.

Transmitter to Operator Matching (Pairing)

The On-Board Radio Receiver RADIORE101, featuring Rolling Code Technology, is factory installed on all operators

equipped with an Electronic Control Board BOARD 070 since November 2013.

The Series 100 Transmitters are compatible with the RADIORE101 Receiver, as well as the on-site installation kits

RADIOKIT004/005 (operators prior to November 2013), the External Radio Receivers RADIORE901/901A/901B and

RADIORE102.

Compatible

Receivers

1-800-361-2260

www.manaras.com

2 TN1054 REV - 2019/07/25

Rolling Code Transmitters - Series "100"

Specifications and Programming Instructions

Matching the Transmitter to the On-Board Radio Receiver RADIORE101 or to the

External Universal Radio Receivers RADIORE901/901A/901B

Note: For RADIORE102, consult TN1028 for pairing instructions.

To MATCH the Transmitter to the Receiver:

Once the Transmitter has been correctly programmed according to instructions

found on p. 1-2, select the Receiver of choice, refer to Figure 1 or Figure 2 and

follow the steps below:

For RADIOEM101/102/103/104:

1. HOLD the Receiver's LEARN button until the LED BLINKS for

approx. 2 sec. (frequency of 1 sec. ON / 1 sec. OFF).

2. To program in

3-Button Mode: On the Transmitter, HOLD any button

until the Receiver's LED stops blinking .

3. To program in 3 x 1-Button Mode: On the Transmitter, HOLD the

desired button that you want programmed until the Receiver's LED

stops blinking .

For RADIOEM144:

1. Adjust the Transmitter's rotary dials to the desired positions to permit for

the proper door selection.

2. HOLD the Receiver's LEARN button until the LED BLINKS for

approx. 2 sec. (frequenc

y of 1 sec. ON / 1 sec. OFF).

3. On the Transmitter, HOLD any button until the Receiver's LED stops

blinking .

Note:

You can match 1-Button, 3-Button, 4-Button AND 144-Door Transmitters

with the same Receiver. Mix and match any of the Series 100 Transmitters

accordingly for your application (ordered separately). One Receiver will accept

up to 50 Transmitters.

To DELETE ALL Transmitters from the Receiver's Memory:

1. HOLD the Receiver's LEARN button until the LED BLINKS for approx. 10 sec. (frequency of 1/3 sec. ON /

1/3 sec. OFF).

1-800-361-2260

www.manaras.com

3 TN1054 REV 0 - 2019/07/25

Figure 1 - RADIORE101

(ECB BOARD070 /

RADIOKIT005)

Figure 2 - RADIORE901

(RADIORE901A/901B)

LEARN

BUTTON

ANTENNA

LED (WHITE)

RADIORE101 (ECB BOAR070) /

RADIOKIT004

(RADIOKIT005)

(On-site Installation Kits)

RADIORE901/901A

(RADIORE900/900A)

RADIORE901B

(RADIORE900B)

RADIORE102

Compatible Receivers

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the paty responsible for compliance could void the user’s

authority to operate the equipment

NOTE: This device has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful

interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to do correct the interference by one or more of the following measures: (1) Reorient or relocate the

receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help

ISED

This device contains license-exempt transmitter/receiver that comply with Innovation Science and Economic Development

Canada's license-exempt RSS(s). Operation is subject to the following wo conditions: (1) This device may not cause interference; and (2)

This device must accept any interference, including interference that may cause undesired operation of the device.