000010418 - 13/03/2019 Assembly Guide Model: 13GMC1 / 13GMC2 / 13GMC3 Floating Shelf Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
In order to ease the assembly, you should separate and identify the parts first Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. *Tools Needed (not supplied) IMPORTANT In order to avoid severe or even fatal injuries, follow the instructions carefully.
L W P2 H P4 P1 ASSEMBLED PRODUCT: H: 12.59'' W:13.77'' L:11.22'' 26 Lbs P1 P3 Lbs Maximum weight supported distributed Hardware list F1 F2 F3 1000008297 1000008616 1000009033 Qty. 4 Qty. 4 Qty. 1 F4 F5 F6 1000000281 - WHITE 1000007352 - BLACK 1000010221 - BLUE 3000008409 1000008285 Qty. 4 Qty. 1 Qty.
1 - Attach the parts P1, under the part P4. Positioning the cut-out of part P4 over the safety grappel of parts P1.
1 - Slightly incline the part P3, and place it inside the cut - out of the parts P1. 2 - Slide part P3 into the folds of parts P1 and. P3 P1 P4 P1 P3 P3 01 03 1 - With the end of F3, smash the safety claw, locking part P3 to part P1 and P4. 2 - Finish folding it mannually.
IMPORTANT: REMOVE THIS RIBBON ONLY TO CONTINUE MOUNTING P2 01 05 1 - Attach the P3 part onto the P1 and P2 parts. 2 - Check all the fittings, before continuing.
1 - With the end of F3, smash the safety claw, locking part P1 to part P2 and P4. 2 - Finish folding it mannually. P2 P2 F3 P1 P4 P1 P4 07 01 07 1 - Using the F5 template, make markings on the wall as indicated. 2 - It is necessary to use the level. 3 - Drill the wall over the marked points.
1 - Insert the metal part of the bushing into the hole until it overcomes the wall. 2 - Pull the bushing driving it against the wall and then push the plastic ring until it leans close to the wall.
1- Insert the screw F2 into the hole on the wall. 2- Turn the screw clockwise, using the F3 part . 2x F2 F3 01 10 1- Approach the cabinet by fitting the F2 screw.
1 - Align the cabinet with the use of a level. 2 - Mark the wall through the holes in the bottom of the cabinet. 0° 01 12 1 - Move the cabinet away 2 - Drill the wall over the marked points.
1 - Insert the metal part of the bushing into the hole until it overcomes the wall. 2 - Pull the bushing driving it against the wall and then push the plastic ring until it leans close to the wall.
1 - Position cabinet through the F2 screws that are already attached to the wall. 2 - Insert screw F2 through part P4. 2 - Turn the screw using the F3 part clockwise. 2x F2 F3 01 15 F2 F3 2X 1X 1 - Press part F4 against the heads of the F2 screws.
IMPORTANT: REMOVE THE RIBBON TO FINISH THE ASSEMBLY 01 17
TAKING GOOD CARE OF YOUR CABINET Cleaning and caring instructions: - Avoid dragging objects on top of the cabinet. They might scratch the finishing. - Only non-abrasive natural chemical products are recommended to clean your cabinet. Simply wipe the cabinet down with a wet cloth to remove the cleaning product excess. - Never clean the cabinet with scouring powders, steel scrubber pads or any other product which can scratch its surface. - Chemical products are not recommended.
WARRANTS TERMS This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date of the original consumer purchase. Proof of original purchase date is required to obtain service or replacement under this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the store where he purchased the product. In the warranty period, any defective parts will be replaced free of charge by another of the same line and model.
Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.
