DR002 V.
STOP! Before beginning the assembly process, ensure all boxes and parts have been delivered. FOR BEST RESULTS: • Do not throw away packaging materials until assembly is complete. • Assemble item on a soft surface, such as cardboard or carpet, to protect finish. • Proper assembly requires two people. Support Site View our assembly video online: WWW.MANHATTANCOMFORT.COM Stuck? Question? We are here to help. tel: 908-888-0818 e-mail: help@manhattancomfort.
Included in this package: A: TOP (1) B: BOTTOM (1) C: LEFT END (1) D: RIGHT END (1) E: CONNECTING BOARD (1) F: BACK (2) G: DRAWER FRONT (5) H: DRAWER SIDE LEFT (5) J: DRAWER SIDE RIGHT (5) L: DRAWER BACK (5) M: DRAWER BOTTOM (5) O: DRAWER BOTTOM SUPPORT (5) P: LEG (4) Q: CONNECTING TUBE (2) DR002 Page 3
Hardware Identification Page 4 DR002
DR002 Page 5 2 ea 0lb ch s s 50 lb
Step 1 ◆ Insert four WOOD DOWELS (5) to the BOTTOM (B). ◆ Attach the BOTTOM (B) to the ENDS ( C and D), fasten the BOTTOM (B) by using four BOLTS (1).
Step 2 ◆ Slot the CONNECTING BOARD (E) to the ENDS (C and D).
Step 3 ◆ Attach the two CONNECTING TUBES (Q) to ENDS (C and D) by using eight BOLTS (2).
Step 4 ◆ Insert four WOOD DOWELS (5) to the TOP (A). ◆ Attach the TOP (A) to the ENDS (C and D), tighten four PLASTIC CAM LOCKS.
Step 5 ◆ Fasten the two CONNECTING TUBES (Q) to the TOP (A) by using four BOLTS (3).
Step 6 ◆ Fasten two BACKS (F) to the TOP (A), ENDS (C and D) and the BOTTOM (B) by using twenty BOLTS (1). ◆ You should start each BOLT a few turns before completely tightening any of them.
Step 7 ◆ Fasten the LEGS (P) to the BOTTOM (B) by using sixteen BOLTS (2).
Step 8 Attach the DRAWER SIDES (J and H) to the DRAWER FRONT (G), ◆ slide the PLASTIC CONNECTIONS to the grooves. ◆ DR002 Slot the DRAWER BOTTOM SUPPORT (O) to the DRAWER FRONT (G).
Step 9 ◆ Slide the DRAWER BOTTOM (M) into the grooves, in the DRWAER SIDES (J and H), and the DRAWER FRONT (G). ◆ Fasten the DRAWER BACK (L) to the DRAWER SIDES (J and H) and the DRAWER BOTTOM SUPPORT (O) by using six BOLTS (1). Repeat the Step 8 and Step 9 on the other drawers..
Step 10 ◆ Use two BOLTS (2) to fasten the PULL (4) to DRAWER FRONT (G). Repeat the same on the other drawers.
Step 11 To insert the DRAWER into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit. ◆ Before the drawer is fully inserted, please make sure the interlock pins on the EXTENSION SLIDES on the drawer is pushed forward as shown on the diagram. The drawer should push in hard until it is all the way in , then it will slide in and out easier.
Step 12 Open the FURNITURE TIPPING RESTRAINT KIT (96) and fasten the SAFETY STRAP to the TOP (A). ◆ Use the SHORT SCREW through the hole in the strap and into the top surface of the TOP (1). Place your unit in its final location. ◆ NOTE: The following instructions show your unit being fastened to a wall stud. If you are not fastening your unit wall stud, go to the next step now. 1st- Locate the center of a stud in your wall near your unit and mark it with a pencil.
Step 13 1st- With your pencil, strike a mark through the center of the hole in the SAFETY STRAP. 2nd- Drill a 3/8" hole on the mark. ◆ 3rd- While you squeeze the wings together, gently tap the WALL ANCHOR from the FURNITURE TIPPING RESTRAINT KIT (96) into the hole until it is even with the surface of the wall. 4th- Turn the LONG SCREW through the hole in the SAFETY STRAP and into the WALL ANCHOR. ◆ NOTE: You will need to turn the LONG SCREW multiple turns to completely tighten and secure your unit.
WARRANTY POLICY All Manhattan Comfort furniture products are warranted, to the original purchaser at the time of purchase and for a period of 30 days thereafter. Our warranty is limited to new products purchased in factory sealed cartons. This warranty is valid in the United States of America and Canada. In order to provide you with timely assistance, please thoroughly inspect your furniture for missing or defective parts immediately after opening the carton.
DR003 V.
STOP! Before beginning the assembly process, ensure all boxes and parts have been delivered. FOR BEST RESULTS: • Do not throw away packaging materials until assembly is complete. • Assemble item on a soft surface, such as cardboard or carpet, to protect finish. • Proper assembly requires two people. Support Site View our assembly video online: WWW.MANHATTANCOMFORT.COM Stuck? Question? We are here to help. tel: 908-888-0818 e-mail: help@manhattancomfort.
Included in this package: A: TOP (1) B: BOTTOM (1) C: LEFT END (1) D: RIGHT END (1) E: MIDDLE UPRIGHT (1) F: BACK (2) G: DRAWER FRONT (6) H: DRAWER SIDE LEFT (6) J: DRAWER SIDE RIGHT (6) L: DRAWER BACK (6) M: DRAWER BOTTOM (6) O: DRAWER BOTTOM SUPPORT (6) P: LEG (6) Q: CONNECTING TUBE (4) DR003 Page 3
Hardware Identification Page 4 DR003
DR003 Page 5 20 ea lb ch s s lb 50
Step 1 ◆ Insert six WOOD DOWELS (5) to the BOTTOM (B). ◆ Attach the BOTTOM (B) to the ENDS ( C and D) and the MIDDLE UPRIGHT (E), fasten the BOTTOM (B) by using six BOLTS (1).
Step 2 Attach the four CONNECTING TUBES (Q) to the ENDS (C and D) and the MIDDLE UPRIGHT (E), ◆ by using sixteen BOLTS (2).
Step 3 ◆ Insert six WOOD DOWELS (5) to the TOP (A). Attach the TOP (A) to the ENDS (C and D) and the MIDDLE UPRIGHT (E), ◆ tighten six PLASTIC CAM LOCKS.
Step 4 ◆ Fasten the four CONNECTING TUBES (Q) to the TOP (A) by using eight BOLTS (3).
Step 5 ◆ Fasten two BACKS (F) to the TOP (A), the ENDS (C and D), the MIDDLE UPRIGHT (E) and the BOTTOM (B) by using twenty four BOLTS (1). ◆ You should start each BOLT a few turns before completely tightening any of them.
Step 6 ◆ Fasten the LEGS (P) to the BOTTOM (B) by using twenty four BOLTS (2).
Step 7 ◆ Attach the DRAWER SIDES (J and H) to the DRAWER FRONT (G), slide the PLASTIC CONNECTIONS to the grooves. ◆ Slot the DRAWER BOTTOM SUPPORT (O) to the DRAWER FRONT (G).
Step 8 Slide the DRAWER BOTTOM (M) into the grooves, in the DRAWER SIDES (J and H), ◆ and the DRAWER FRONT (G). ◆ Fasten the DRAWER BACK (L) to the DRAWER SIDES (J and H) and the DRAWER BOTTOM SUPPORT (O) by using six BOLTS (1). Repeat the Step 7 and Step 8 on the other drawers.
Step 9 ◆ Use two BOLTS (2) to fasten the PULL (4) to the DRAWER FRONT (G). Repeat the same on the other drawers.
Step 10 To insert the DRAWER into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit. ◆ Before the drawer is fully inserted, please make sure the interlock pins on the EXTENSION SLIDES on the drawer is pushed forward as shown on the diagram. The drawer should push in hard until it is all the way in , then it will slide in and out easier.
Step 11 Open the FURNITURE TIPPING RESTRAINT KIT (96) and fasten the SAFETY STRAP to the TOP (A). ◆ Use the SHORT SCREW through the hole in the strap and into the top surface of the TOP (1). Place your unit in its final location. ◆ NOTE: The following instructions show your unit being fastened to a wall stud. If you are not fastening your unit wall stud, go to the next step now. 1st- Locate the center of a stud in your wall near your unit and mark it with a pencil.
Step 12 1st- With your pencil, strike a mark through the center of the hole in the SAFETY STRAP. 2nd- Drill a 3/8" hole on the mark. ◆ 3rd- While you squeeze the wings together, gently tap the WALL ANCHOR from the FURNITURE TIPPING RESTRAINT KIT (96) into the hole until it is even with the surface of the wall. 4th- Turn the LONG SCREW through the hole in the SAFETY STRAP and into the WALL ANCHOR. ◆ NOTE: You will need to turn the LONG SCREW multiple turns to completely tighten and secure your unit.
WARRANTY POLICY All Manhattan Comfort furniture products are warranted, to the original purchaser at the time of purchase and for a period of 30 days thereafter. Our warranty is limited to new products purchased in factory sealed cartons. This warranty is valid in the United States of America and Canada. In order to provide you with timely assistance, please thoroughly inspect your furniture for missing or defective parts immediately after opening the carton.
