888-230-2225 help@manhattancomfort.com 319 RIDGE RD, DAYTON, NJ08810, NEW JERSEY - UNITED STATES Hampton home office desk 40.
Technical information Maximum supported weight Dimension: W: 53.54" H: 29.92" D: 20.
FRONT VIEW REAR VIEW 06 05 02 03 10 09 09 08 01 10 10 07 04 04 07 PART 01 02 03 04 05 06 07 08 09 10 DESCRIPTION RIGHT SIDE FRAME SHELF CROSSBAR LEFT SIDE TOP FEET BACK COVER TOP/ BASE OF THE NICHE SIDE OF THE NICHE QUANTITY 01 01 01 02 01 01 02 01 02 03 HARDWARE A 22x B 04x C 04x D 04x E 04x F 06x G 08x H 02x I 18x J 02x 2
STEP 1 F B 06 B 04 F B 04 F B F F 06x F B 02 04x F - Insert the hardware (B) in the part (06). - Insert the hardware (F) in the parts (02, 04). STEP 2 A A 02 A 05 10x 04 A 03 A A A A 04 01 A A - Connect the parts (01, 02, 03, 04, 05) with the hardware (A). STEP 3 04x C C 05 C E+D 06 01 E D 04x E+D E+D - Connect the parts (01, 05) onto the part (06) with the hardware (C). E+D 3 - Connect the hardware (E) onto the parts (01, 05) with the hardware (D).
STEP 4 08x G G G G H G 07 06 H G G 07 - Connect the hardware (H) under the part (06) with the hardware (G). - Then, screw the parts (07) into the hardware (H). STEP 5 10 09 10 A A A 12x A A 10 09 A A A A - Connect the parts (09, 10) with the hardware (A). STEP 6 05 02 J J 02x 4 - Connect the niche onto the parts (02, 05) with the hardware (J).
888-230-2225 help@manhattancomfort.
Technical information Maximum supported weight Dimension: W: 24.80" H: 60.12" D: 12.
FRONT VIEW 03 REAR VIEW 01 08 10 09 04 05 02 09 10 07 09 06 07 07 PART 01 02 03 04 05 06 07 08 09 10 QUANTITY 01 01 01 01 01 01 04 01 03 02 DESCRIPTION TOP RIGHT SIDE CROSSBAR FIXED SHELF LEFT SIDE BASE FEET BACK COVER (DRILLED) BACK COVER ADJUSTABLE SHELF HARDWARE A 20x B 01x C 01x D 04x E 01x J 02x K 02x E U GL G 04x H 01x I 44x 2 F 08x
STEP 1 GG 03 F 08X F F GG F 05 F F G F 04X 02 F F - Insert the hardware (F) in the parts (02, 05). - Insert the hardware (G) in the part (03). STEP 2 03 01 A 04 A 02 A A 04x A - Connect the parts (01, 02, 03, 04) with the hardware (A). STEP 3 03 01 A A 05 04 A A 04x A 3 - Connect the part (05) onto the parts (01, 03, 04) with the hardware (A).
STEP 4 A 04x 02 A 06 05 A A A - Connect the part (06) onto the parts (02, 05) with hardware (A). STEP 5 I J 36X 08 D+I 09 D+I 02x D+I D+I 09 04X 09 I D - Insert the hardware (J) as showed on detail. - Connect the two parts (09) with the hardware (I+D). - Connect the parts (08, 09) with the hardware (I). STEP 6 08X A USE THE GLUE (C) BEFORE FASTENING THE FEET (07). A 07 A C 06 07 07 07 07 4 - Connect the parts (07) under the part (06) using two screws (A) for each one.
STEP 7 10 10 - Insert the parts (10) as showed above. STEP 8 Attention! This step is very important! You need to attach to the furniture on the wall to avoid any tip over risk. Follow the procedures as showed below. H WALL 08 Pass the hardware (H) through the hole of the part (08) as shown in the figure. You will need a pencil to mark where you should drill the wall with a 3/8" drill bit to put in the hardware (E). Approach as close as possible to the wall.
