000008415 - 15/03/2018 ASSEMBLY HANDBOOK – FORTRESS 31.5" MOBILE GARAGE CABINET WITH DRAWER AND SHELVES 2GMCF Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.com View our assembly video online www.manhattancomfort.
In order to ease the assembly, you should separate and identify the parts first Necessary hardware for the assembly * Included in the kit Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. Stuck? Questions? We are here to help. 1-888-230-2225 help@manhattancomfort.com View our assembly video online www.manhattancomfort.com IMPORTANT In order to avoid severe or even fatal injuries, follow the instructions carefully.
ASSEMBLY HANDBOOK – FORTRESS 31.
STEP 1 1 - Fit part P7 inside part P3 2 - Fit both parts in the frontal side, with F1 F1 2x P3 P7 STEP 2 1 - Fit part P2 inside part P7 2 - Fit both parts in the frontal side, with F1 F1 2x P3 P7 P2
STEP 3 F1 1 - Fit part P5 between part P2 and P3 2 - Check that all 4 tabs have been fitted 3 - Fit part P5 to parts P2 and P3, at the frontal side, with F1 1 4x 2 P5 P3 P7 3 P2 STEP 4 F1 1 - Turn the cabinet with the back side upwards 2 - Fit parts P2 and P3 to parts P5 and P7 with F1 8x 180° P2 P7 P2 P5 P5 P3 180° P7 P3
STEP 5 1 - Fit part P10 into parts P2, P3 and P5 Check that all fits are supported over the bolts 2 - After fitting the parts, screw the bolts until locked 1 P2 2 STEP 6 WARNING P10 Position part P10 on the P5 side for mounting the cabinet.
STEP 7 1 - To assembly the cabinet with shoe fit the accessory F9 in part P7 as illustrated here below and turn to screw. To level the height or the cabinet, turn the shoe either clockwise or counterclockwise to align it.
STEP 9 F7 1 - Fit the lower part P19 in diagonal position to insert it inside the cupboard 2 - Lean part P19 in part P2, P3 and place it over the F7 detailed in the figure here below 3 - Lower the other side of part P19, leaning it over the left F7 P5 P3 P19 P2 P7 STEP 10 F1 1 - Insert part P17 inside the cabinet, in diagonal position.
STEP 11 1 - To assembly the doors, fit door P26 lower hinge bolt inside the bushing fixed in part P7 2 - Then, pull down the pin of door P26 upper hinge; align the door and release the pin to fit the bushing fixed in part P17 3 - Repeat the step for part P27 1º P5 P2 P19 P17 P26 P3 P7 P27 STEP 12 1 - Fit part P15 to part P28 2 - Fit them with F1 F1 3x P15 P28 2º
STEP 13 1 - Align parts P12 and P13 to part P15, until it leans against part P28 2 - Fit them with F1 F1 4x P13 P12 P15 P28 STEP 14 F1 1 - Insert part P14 over part P15 and between parts P12 and P13 2 - Then, fix part P14 to parts P12, P13 and P15, with F1 5x P14 P13 P15 P28 P12
STEP 14 1 - Fit the drawers – already assembled – between parts P2 and P3, through the slidings 2 - Check that slidings of both sides are properly fitted.