For Best Results Bo nok throw away packaging materials until assembly Is complete, Assemble item on a soft surface, such as cardboard or carpet, to protect finish. Proper assembly requires two people.
Included in this Package 01 Lower Top x -] 02 LEFT SIDE x1 = Ma Arum 03 LOWER BACK xt Lbs) supported.
Prepare the pieces Step 1 Insert the wooden dowels (F) into parts and 10. Remember to use the glue {U). It's important to glue the wooden dowel. F 6X30MM WOODEN DOWEL U WHITE GLUE x36 x1 Step 2 Insert screw (B} into part 02, 04, 11 and 14. Tighten to the limit. A MINI FIX SCREW x22 Step 3 Insert two hinge pin (T) into parts 01, and 13.
Assembly Step 4 Put parts 05 and 06 together with part 04. Insert the six mini fix connectors {B) in parts 05 and 06 and rotate clockwise as shown. Tighten to the limit. Tighten the minimize up to the limit to assembly don't be slack. U-WHITE GLUE. B15MM CONNECTOR x1 ® Step 5 Put the glue (U) in the wooden dowel (F} already fixed into part 07. Then put parts together with part 04. It’s important to glue Cd the wooden dowel.
Assembly Step 7 Put the glue (U) in the wooden dowel (F) already fixed into parts 10. Then put the parts 10 together with part 11. Insert the four mini fix connectors (B) and rotate clockwise as shown. Tighten to the limit. Tighten the mini fix up to the limit {0 assembly don’t be slack, A It’s important to glue 2 the wooden dowel. B15MM CONNECTOR WHITE GLUE x1 Step 8 Put the glue (U) in the wooden dowel (F) already fixed into parts 10, then put the part 11 on the sides 10.
Assembly Step 10 Put the parts 01 and 02 together and — use two screws (D) and the Allen wrench (E). FALLEN WRENCH iff ha Step 11 Put the part 03 together in the parts 01 and 02 and use one screw (D) through of the part 01, and one mini fix connector {B) In part 03, and rotate Tighten the mini fix up to the limit clockwise as shown. Tighten to the "to assembly don't bbe stack. limit.
Assembly Step 13 Put the part 09 together in the part 02 and use two mini fix connector (B) and rotate clockwise as shown. Tighten to the limit, Tighten the mint up to the Emit 0 assembly don't be slack. = B-15MM CONNECTOR Step 14 Insert two shelf support in part 02 and insert the niche. When it is ok, insert four screw (L) through parts 10 and 02 according to the drawing.
Assembly Step 15 Put the part 12 together in the part 02 Ir 3 and use one screw {D} through the part = 11, and one mini fix connector (B) in part 12, and rotate clockwise as shown, E-ALLEN WRENCH Tighten to the limit. D7X50 SCREW B15MM CONNECTOR x1 x1 AVAST Tighten the mink up to the mit 0 assembly don’t be slack. Step 16 Put the part 13 together In the parts 02 and 12 and use three screws (D} and the Allen wrench (E).
Assembly Step 17 Put the part 14 together in the parts 01 and 13 and use five screws (D) and the Allen wrench (E). When It Is ok, insert two shelf support in part 14 and Insert four screw (L} through part 14. FALLEN WRENCH xL Dvn SCREW 7X50 SCREW x Step 18 Put feet on part 01 as the drawing. On each foot {I}, use two screws (H) on each foot, with the Allen wrench (E).
Assembly Step 19 Insert the screw (G) through parts 02 and 14 according to the drawing using the Allen wrench (E). The screw {G) must fix parts 02 and 14 on the feet {I). FALLEN WRENCH 1/4X25MM SCREW x4 Step 20 Fix the backs 15 and 16 using the balls {1).
Assembly Step 21 Put the hinges for glass (P) and the doors (18) together and screw using a Philips wrench, according to the drawing HINGE FOR GLASS x2 Step 22 Insert the magnets to close door (0) in parts 01 and 13 and use four screw (M} according to the drawing.
Assembly Step 23 Insert the hinges for glass (P) already fixed In the door (18) In hinge pin (T) already fixed into part 01. Be careful It’s a glass door extremely fragile HINGE FOR GLASS | 1. HINGE PIN xl x1 Step 24 Insert the hinges for glass (P) in hinge pin already fixed into part 13, hold the door hinges for glass (P) and insert the door according to the drawing. When It is ok, insert the screw (N} from Inside the door, tighten into the handle (S) on the outside.
Assembly Step 25 As In step 23, Insert the hinges for glass {P) already fixed in the door, in hinge pin (7) already fixed Into part 01. Be careful It’s a glass door extremely fragile P HINGE FOR GLASS x Step 26 As in step 24, Insert the hinges for glass {P) in hinge pin already fixed into part 13, hold the door hinges for glass (P) and insert the door according to the drawing. When It Is ok, insert the screw (N} from Inside the door, tighten into the handle (S} on the outside.
Assembly Step 27 Insert the backstop (Q) in the doors (18) according to the drawing.
Safe and Security KIT FOR DRYWALL ow -prewar Go to Step 29 (— DWI-x1 DOWSE -x1 KIT FOR MASONRY mw = Masonry wall Go to Step 33 Bette CI=A©) MW1 -x4 MW2 -x4 MW3 -x4 MW4 -x4 MEWS -x2 WARNING Serious or fatal crushing injuries can occur from furniture tip-over. ALWAYS secure this furniture to the wall using tip-over restraints. To further reduce the risk of serious injury and death from tip-overs: Place heaviest items in the lower drawer. Do not set TVs or other heavy objects on the top of this product.
Safe and Security KIT FOR DRYWALL 1. Make holes on the wall following the model below and specifications: Step 29 & 14mm drill. ¥ Depth of 60mm A Use an electric drill. 8. Put the corner (DW4) on the upper top (13) of the product.
Safe and Security 9. Put the glass-door cabinet to the wall and aligning the hole in the safety block with the hole that was made the drywall. Done so, insert the screw up to its maximum limit on, Step 31 19.
KIT FOR MASONRY 1. Make holes on the wall following the model below and specifications: Step 33 i 8mm drill. ¥ Depth of 50mm A Use an electric drill. 2. Insert the bushing into the hole made on the wall, 3. Put the screws into the bushings, but don’t tighten until Step 35 the end. it’s necessary 0.33" {10mm} deft to ft on the lock.
4, Put the locked on the horizontal as the pictures below, A Check the distance between wall's holes. i must be the same distance between centers of product's device. 5. Drag the product carefully until you meet the screw’s head. Fit the screw into the jock as the picture below.
TAKING GOOD CARE OF YOUR FURNITURE Cleaning and caring instructions: Wipe the wood furniture down with a moist cloth to properly clean the furniture. Do not forget to dry your furniture out. Humidity can damage the finish or create mold. Chemical products are not recommended; Never clean the furniture with scouring powders, steel scrubber pads or any other product which can scratch its Furniture surfaces should not be covered with colored plastic or paper sheets.