Manual

ManualsBrandsMantis Manualshedge trimmerOfficial Mantis hedge trimmer

LITTLE

OWNER'SMANUALandSAFETYINSTRUCTIONS

i_I i _ _ i _ _ _ i _ _ i _ i i _ii_

Single Edged (Models 19!0, 2410,3010, 1912,2412, 30!2)

_nd Double Edged (Models !920, 2420, 3020, 1922, 2422, 3022)

Electric HedgeTrimmers

WARNING DANGER

BLADES ARE EXTREMELY SHARP.

TO AVOID INJURY WHEN UNPACKING

THE HEDGE TRIMMER,

DO NOT GRASP THE BLADES.

(_ MANUELDEL'UTILISATEURINSTRUCTIONSDE

SECURITE

tranchant unique (modUles 1910, 2410, 3010, 1912, 2412 et 3012)

et _ double tranchant (modUles 1920, 2420, 3020, 1922, 2422 et 3022)

Taille-haies _lectriques

AA TrSSEMEN ANCER

LES LAMES SONT EXTREMEMENT

COUPANTES. POUR EVITER DE SE BLESSER

PENDANT LE DEBALLAGE DE L!APPAREIL,

NE PAS LE SAISIR PAR LA LAME.

MANUALDELPROPIETARIOe INSTRUCCIONESDE

SEGURIDAD

para las unidades con una sola cuchilla (modelos 1910, 2410, 30!0, 1912, 2412, 3012)

y las unidades con dos cuchillas (moddos 1920, 2420, 3020, 1922, 2422, 3022)

Podadora de arbustos dOctrica

_ AD VERTENCrA I'ELIGRO

LAS CUCHILLAS ESTAN

EXTREMADAMENTE F!LosAs: PARA

EVITARSE UNA LESION AL DESEMPACAR

LA PODADORA DE ARBUSTOS, NO LA

SOSTENGA POR LAS CUCHILLAS.

Summary of content (14 pages)

PAGE 1
LITTLE OWNER'SMANUAL and SAFETYINSTRUCTIONS i_ _ i _ _ _ i _ _i _ i i _ii_ WARNING i_I Single Edged (Models 19!0, 2410,3010, 1912,2412, 30!2) _nd Double Edged (Models !920, 2420, 3020, 1922, 2422, 3022) Electric HedgeTrimmers (_ et INSTRUCTIONS MANUELDEL'UTILISATEUR DE SECURITE tranchant unique (modUles 1910, 2410, 3010, 1912, 2412 et 3012) et _ double tranchant (modUles 1920, 2420, 3020, 1922, 2422 et 3022) Taille-haies _lectriques MANUALDELPROPIETARIO e INSTRUCCIONES DE SEGURIDAD para las unid
PAGE 2
TABLE OF CONTENTS Page I. IMPORTANT INFORMATION A. Introduction ....................................................................................................... 2 3 II. GENERAL SAFETY RULES ........................................................................................... A. Safety Decals ...................................................................................................... B. Safety Symbols Identification ..............................................................
PAGE 3
IL GENERAL SAFETY RULES Warl1111g: When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before operating product and save these instructions. this For safe operations: 1__ Keep work area clean. Cluttered areas and benches invite injuries. 2__ Consider work area environment. Do not expose power tools to rain. Do not use power tools in damp or wet locations.
PAGE 4
A A. SAFETY DECALS AND MOLDED SYMBOLS Important parts of the safety system incorporated in both Single Edge and Double Edge trimmers are the warning and informational decals and molded-in symbols found on various parts of the trimmer. These decals must be replaced in time due to abrasion, etc. Single It is your responsibility to replace thedecals or molded housing when they become hard to read. The locations of these safety features are shown below.
PAGE 5
A C. SPECIAL SAFETY 1. Read and understand particular attention . the owner's manual. Pay to all sections regarding safety. Always keep a firna grip on both handles while the blades are moving and/or the motor is running. On Single Edged units, the right hand grasps the front side handle and the left hand grasps the rear handle. On Double Edged units, one hand grasps the front 'loop' handle, while the other hand grasps the rear handle. D. WARNINGS -- Don't overreach or stand on unstable support.
PAGE 6
Ill. UNPACKING A HEDGE ASSEMBLY WARNING BLADES AVOID AND ARE DANGER EXTREMELY INJURY INSTRUCTIONS WHEN TRIMMER, DO SHARE UNPACKING NOT GRASP TO THE THE BLADES. Your Lit.tl_ H!ond_r hedge trimmer has been assembled for you at the factory. Before operating IV. A. be sure all fasteners are secure, and all guards devices are in place and operating properly. and safety OPERATION INSTRUCTIONS FOR PROPER OPERATION Securing extension the cord.
PAGE 7
Read care and safety instructions carefully before attempting to use this trimmer. Only after you are familiar with your hedge trimmer and all of its controls and the functions should you start the trimmer. Before plugging into an electric voltage supply is as specified on Models 1910, 1920, 2410, 2420, 464 watts at 115 volt,s. Models 1912, 1922, 2412, 2422, 390 watts at 230 volts. extension cord over hedge being trimmed. On 120V units, use 16 gauge wire extension cord up to 100 feet.
PAGE 8
VL SERVICE A. TROUBLE SHOOTING Problem 1. Blades don't 2. Blades don't turned on. cut Cause cleanly. move Blades are dull or not properly. when Blades Worn 3. Excessive electrical arcing from vents in top of trimmer. B. BLADE Remedy are adjusted too tight. brushes. Have blades adjusted. sharpened and Re-adjust blades following service instructions. Replace service brushes - follow instructions.
PAGE 9
Single Edge Assembly iNSTALL WIRES THROUGH KEY 1 2 2 2 3 4 5 5 5 6 6 6 7 7 7 8 9 9 9 10 10 10 11 12 WIRE FROM TROUGH PART # DESCRIPTION 310100 Gear Housing Assembly {including pressed in pins / 16-54B Nut Lock 1/4-28 whiz Flange (for models 3010, 3012 / 30" SE 16-54B INut Lock 1/4-28 whiz Flange (for models 2410 2412} 24" SE 16-54B Nut Lock 1/4-28 whiz Flange (for models 1910, 1912} 19" SE 310106 Frame Bar Support NA Side Handle Assembly {See individual part numbers) IFrameBar a_semblv(fnr mndel_,_010
PAGE 10
Double Edge Assembly & KEY # 1 2 2 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 11 10 ® PART # DES CRIPTION 310100 Gear Housing Assembly iincludin_ pressed in pins} 16-54B Nut Lock 1/4-28 whiz Flange {for models 3020_ 3022) 30" DE 16-54B Nut Lock 1/4-28 whiz Flange ifor models 2420, 24221 24" DE 16-54B Nut Lock 1/4-28 whiz Flange {for models 1920, 1922} 19" DE 300300 Frame Bar Support NA Loop Handle Assembly (See individual part numbers} 310325 Frame Bar assembly (for models 3020.
PAGE 11
Gear/Motor Assembly t % \ < KEY # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 14 15 17 18 18 19 20 21 22 PART # 310100 16-57A 310407 D16-71 16-62 D16-59 16-64 16-65 16-67 16-81-1 310503 3042 D16-56F 310903 310900 310108 16-69D 310901 310902 16-69E 3025 310105 3026 DESCRIPTION Gear Housing Assembly Gear Housing Cover Plate Grommet Rubber Gasket Cover Plate Eccentric Gear Cluster Gear Connectin _ Rod Spacer Connecting Rod Felt QTY.
PAGE 12
Double Edge Front Loop Handle NORMALLY CLOSED Assembly BLACK WIRES SET OF 13) NORMALLY OPEN TO PC BOARD ATTACH RED KEY# 1 2 3 4 5 6 7 8 PART# 3033 310405 310219 310203 310207 310504 310500 310218 DESCRIPTION Switch Normally Open Switch Normally Closed Loop Handle Tri_er Set Loop Handle Set Shield Screw Plasti-Tite #8 x 1" Screw Plasti-Tite #g × 3/4" Loop Handle Trigger Strap QTY.
PAGE 13
Main Housing Assembly RED WIRES AT[ACH KEY # 1 2 3 5 5 5 5 6 7 8 9 10 ll 11 12 13 TO FRONT SWITCHES BLACK WIRE PART # DESCRIPTION 310400 Main Housing Set 310403 Housing Brush Cap Cover Plate 310404 Housin_ Loon Handle Cover Plate * 310438 PC Board Assembly (for Models 3012, 310436 PC Board Assembly (for Models 3010, 310439 PC Board Assembly (for Models 3022, 310437 PC Retard A_emhlv (fc)r McMel_ 3090 310209 Trigger Rear Housing 3033 Switch Normally Open 310405 Switch Normally Closed 310500 Screw_ Plas
PAGE 14
VIII. SPECIFICATIONS Cutting Model Weight kg (lb) Length cm (in.) The A-weighted emission sound pressure level at the operator position has been measured at: L1,A= 80 dB(A). These measurements were made in accordance with EN ISO 11201:1996 under no-load conditions. 1912 48 (19) 3.49 (7.7) 1922 48 (19) 3.89 (8.6) 2412 61 (24) 3.62 (8.0) 2422 61 (24) 4.04 (8.9) 3012 76 (30) 76 (30) 3.85 (8.5) 3022 All listed hedge trimmers 230 volts AC at 50 hertz. The Hand-Arm weighted r.m.