Manual

Read care and safety instructions carefully before
attempting to use this trimmer. Only after you are
familiar with your hedge trimmer and all of its controls
and the functions should you start the trimmer.
Before plugging into an electric circuit, be sure that the
voltage supply is as specified on hedge trimmer.
Models 1910, 1920, 2410, 2420, 3010, 3020 are rated at
464 watts at 115 volt,s.
Models 1912, 1922, 2412, 2422, 3012, 3022 are rated at
390 watts at 230 volts.
Be sure the switches are in the "off" {not depressed}
position before connecting unit to the applicable
current. (120V AC or 220V/240V AC.} Do not carry a
plugged -in trimmer with a finger on the switch.
The electricity for this hedge trimmer should be
supplied through a Residual Current Device (RCD} with
a tripping current of not more than 30 mA. These
protective devices are also known as Residual Current
Circuit Breakers (RCCBs} or Earth Leakage Circuit
Breakers (ELCBs}.
5. Keep extension cord behind trimmer. Never drape
6.
7.
extension cord over hedge being trimmed. On 120V
units, use 16 gauge wire extension cord up to 100 feet.
Over 100 feet use 14 or heavier gauge wire or extension
cord. Cords are available from your local Little Wonder
dealer. The use of light gauge lamp cords or sizes lighter
than those specified above will result in loss of power,
possible motor failure, overheating of cord and the
possibility of fire.
Warning! These trimmers have been designed so they
can only be operated when using both hands. Do not
attempt to override this important safety feature in any
way.
Hold trimmer firmly. For Single Edge Model, keep right
hand on side handle and left hand on rear handle. For
Double Edge Model, you can place either hand on either
handle. Squeeze both switches.
Tilt trimmer so cutting tooth is angled slightly toward
the hedge or shrub and proceed to cut. Use
overlapping sweeping motions away from your body to
achieve a safe and even cut. The unit is designed
to cut any type of hedge or shrub; however, _'_
thickness of cut should not exceed 1/2 inch { 1/2" )
in diameter.
V. MAINTENANCE
Remove the plug from the socket before carrying out any adjustment, servicing, or maintainence.
A. LUBRICATION AND MAINTENANCE
.
.
A few drops of light (#10) oil should be placed on
the back edge of each blade at each adjusting
screw after approximately every four hours of
normal operation.
To obtain trouble free trimming, it is necessary to
keep the blades lubricated and clean. The gum
that collects and builds up on the blades can be
removed with 50-50 mixture of kerosene and #10
oil. Since a petrolenm product can shorten the life
of sonic plastics, it is necessary to remove excess
oil-kerosene mixture from the plastic parts. Blades
n]ust be clean before they can be adjusted.
Caution! Kerosene and oil are flammable,
.
A few drops of light (#10) or 3-in-1 oil should be
put in the hole indicated on the bottom cover
plate. This is necessary only at the beginning of a
day's operation.
.
Gear housing and motor bearings have been
permanently lubricated with a special grease
which should last for the life of the trimmer. When
blades are replaced, or any other time that the
bottom cover plate is removed, the grease n]ust be
checked for proper anrount (approximately 3/4 full
in the area of the gears), and a new gasket and new
screws nmst be used to insure proper seating of
cover plate. Use only Lubrico M3-3K9K grease
(P/N 16-78A) in the gear housing. Lubrico M24M
(P/N 16-78B) is to be used on the motor bearings.
Lubrico is available through your local Little
Wonder Dealer.
S.
Before each use, inspect to be sure handles, safety
devices and fasteners are secure and in place, and
cord is not frayed. If the supply cord is damaged, it
nmst be replaced by the manufacturer, its service
agent or similarly qualified person in order to
avoid a hazard.
B. SERVICE MAINTENANCE GUIDE
Area Maintenance Frequency
Gear Housing Check Grease Monthly
Blades Inspect / Clean / Lubricate After Each Use
Fasteners Inspect / Tighten / Replace Before Each Use
Labels Inspect / Replace Before Each Use
Handles Inspect / Replace Before Each Use
Guards / Safety Devices Inspect / Replace Before Each Use
IMPORTANT- Time intervals shown are nlaxinlunl. Actual use and your experience will determine the
frequency of required maintenance. 7