Owner's OUTDOOR PATIO HEATER Model JN-MXX If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. H odor continues, keep away from the appliance and Immediately call your gas supplier or fire department. De not store or use gasoline or other flammable vapors and liquids In the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored In the vicinity of this or any other appliance.
PACKAGE CONTENTS HARDWARE CONTENTS (shown actual size) Flange Flange Stainless nut Bolt nut steel bolt Washer 08 a.2 Mex aye 4 Qy.9 Qty.5 Reflector i spacer Wing nut Wrench ding ni Qty. 1 Qty. 3 (not actual size) A\ SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or Install the product. This manual contains Important Information about the assembly, operation and maintenance of this patio heater.
A) safety N Formation & DANGER ~ EXPLOSION FIRE HAZARD « Keep sold combustibles, such as bulking materials, paper or cardboard, a oafs distance away from tho haste 8s commandeered by the instructions. = Provide adequate dears rices around a openings Into the combustion chamber. «Never usa the heater In spaces which do or may contain volatile or airborne combustibles, of products such as gasoline, solvents, paint thinner, dust parties o unknown chemical.
ASSEMBLY INSTRUCTIONS 1. Attach wheel assembly (1) to base (H). Line up holes In wheel bracket with corresponding holes In base, Insert two bolts M8 x 16 (BB) through holes, and finger tighten two M8 flange nuts (AA). Be sure that the wheel assembly is parallel to the base, and fully tighten bolts. Hardware Used @ Messenger om x2 © sometime (ans x2 2. Attach three support brackets loosely to base with three bolts M8 x 16 (BB) downward through support brackets into the Base.
STEP? Learning's protective caver before assembling. Note: If necessary for proper alignment of reflector sections, loosen sate blat prior to further assembly and re tighten after sections are aligned. STEPS Slide two reflector panels together. Insert one screw M6 X 10. Skied one washer © § over threaded nd of screw M6 X 10 and screw on cap nut lonely. STEPS Slide reflector plate root refection panels. Insert one screw ME X 10.
ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S.
OPERATION INSTRUCTIONS CEILING E 4 DANGER + CARBON MONOXIDE HAZARD + For outdoor use only. Never use Adeline house, or other ventilated or enclosed areas. This heater consumes air {oxygen). Do not use In Uninitiated or enclosed areas to avoid endangering your Ile. WALL Caution: Do not attempt to operate until you have read and understand all General Safely Information in this manual and all assembly is complete and leak checks have been performed.
OPERATION INSTRUCTIONS 4 WARNING FOR YOUR SAFETY Be careful when attempting to manually ignites this heater. Holding In the control know for more than 10 ‘seconds bafflers igniting the gas wil cause a ball of flame upon Ignition. When Heater Is ON: Emitter screen will become bright red due to intense heat. The color is more visible at night. Buber will display tongues of blue and yellow flame.
CARE AND MAINTENANCE TROUBLESHOOTING Visually checking portions of the hose assembly located within the confines of the heater post. Inspect the entire hose assembly at least annually, disassembling the reflector and boomer. Inspect the hose [eH POSSIBLE CAUSE [oe Gil Fol] | assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak tested. Lo ‘Wait until the propane cylinder Then assembling the reflector and boomer again following with step 6 and 7.
ONE-YEAR LIMITED WARRANTY REPLACEMENT PARTS LIST This product Is Inspected, tested and carefully packaged to minimize the chance of damage during shipment. If a part within one year from the date of purchase proves to be defective In material or fabrication under normal use, the part will be repaired or replaced. The Company's obligation under the warranty Is to replace or repair defective parts at our discretion.