User Manual

ManualsBrandsMaple Systems ManualsComputer AccessoriesWindows Embedded CE 6.0 Pro Edition

Introduction

Thank you for purchasing a Maple Systems OMI5000 Series Open HMI

This booklet describes the steps necessary for installing the OMI5000

Series touchscreens.

For information on configuring the OMI, please refer to the OMI5000

Series Operations Manual (Windows CE Embedded 6.0 Professional

Edition) [Maple P/N 1010-1016] available for download at

www.maplesystems.com. For additional information, please refer to the

Support Center on the website. The Support Center provides links to

manuals, FAQs, technical notes, training videos, sample projects,

controller information sheets, and controller cables.

Static Awareness

Do NOT remove the rear cover of your OMI5000 Series product – doing

so will void your warranty. When the rear cover is removed the circuitry

inside is exposed to possible damage by electrostatic discharge during

handling. Minimize the possibility of electrostatic discharge by:

 Discharging personal static by grounding yourself prior to

handling the OMI.

 Handling the OMI at a static-free grounded workstation.

 Connecting the frame ground ( ) connector of the OMI to a

clean earth ground.

 Placing the OMI in an antistatic bag during transport.

OPEN HMI

OMI5000 Series

(Windows Embedded CE 6.0 Pro Edition)

Installation Guide

Summary of content (16 pages)

PAGE 1
OPEN HMI OMI5000 Series (Windows Embedded CE 6.0 Pro Edition) Installation Guide Introduction Thank you for purchasing a Maple Systems OMI5000 Series Open HMI This booklet describes the steps necessary for installing the OMI5000 Series touchscreens. For information on configuring the OMI, please refer to the OMI5000 Series Operations Manual (Windows CE Embedded 6.0 Professional Edition) [Maple P/N 1010-1016] available for download at www.maplesystems.com.
PAGE 2
Unpacking the Unit Carefully unpack the OMI. Please read any instructions or cautions that appear on the shipping container. Check all material in the container against the packing list. Maple Systems, Inc. will not accept responsibility for shortages against the packing list unless notified within 30 days. The equipment and accessories were inspected and tested by Maple Systems before shipment; all of the equipment should be in good working order.
PAGE 3
Maple Systems liability is limited to the repair or replacement of the Product only, and not costs of installation, removal, or damage to user’s property or other liabilities. If Maple Systems is unable to repair or replace a nonconforming Product, it may offer a refund of the amount paid to Maple Systems for such Product in full satisfaction of its warranty obligation. Maximum liability of Maple Systems is the cost of the Product. Information furnished by Maple Systems, Inc.
PAGE 4
Environmental Considerations The OMI5000 Series is designed to operate in temperatures from 0° to 50°C (32° to 122°F). It is intended for indoor installations and may not be suitable for use in certain outdoor applications. Avoid installing the OMI5000 Series touchscreens in environments with severe mechanical vibration or shocks. Do not install the OMI in enclosures with rapid temperature variations or high humidity. Either will cause condensation of water inside the device and eventual damage to the OMI.
PAGE 5
Figure 1: Typical Panel Layout OMI5000 (rear side) OMI Power Supply OMI is Control Panel Grounding The control panel must be connected to a good, high-integrity earth ground both for safety considerations and shielding purposes. Maple Systems cannot overemphasize the importance of good grounding. If you fail to use good grounding procedures during installation, sporadic malfunction of the OMI may occur: Connect the OMIs chassis ground terminal to a reliable earth ground with a low-resistance path.
PAGE 6
Technical Note #1027, “OIT Ground Wiring and Electrical Noise Reduction,” which you can find in the Support Center Technical Notes section on our web site. Connect OMI Chassis Ground to Control Panel To reduce the possibility of electrical interference, connect the chassis ground terminal of the OMI to a clean earth ground. If the control panel is metal, make sure it is properly grounded.
PAGE 7
and differential mode attenuation. In applications that may have high frequency noise present, we also recommend using a resistor (~1 MΩ) and capacitor (~4700 pF) in parallel to clean earth ground on the DC output of the power supply. Do not use the power supply used to provide power to the OMI to power switching relays, solenoids, or other active devices.
PAGE 8
Installation It is necessary to follow all installation procedures described in this chapter for electrical noise immunity and CE compliance. Your Maple Systems OMI is designed to connect easily to your Controller. External rear connectors provide quick connections for power, communications and programming wiring. Connect the OMI to Power Use the separate 3-position terminal block supplied with the OMI to provide power to the OMI.
PAGE 9
To connect the OMI to power: 1. Connect the power cable to the OMI. a. Strip the power cable shield to expose 2” of the black and red wires. b. Strip about ¼” of insulation from the black and red wires. c. Connect the red wire to the 24V DC positive (+) input of the OMI power terminal block. d. Connect the black wire to the 24V DC negative (–) input of the OMI power terminal block. e. Connect the power cable shield wire to the OMI power terminal block’s chassis ground input. 2.
PAGE 10
The OMI should be mounted into a panel with a depth of at least 4 in. (105 mm). Allow a clearance of at least 1 in. (25 mm) on each side for mounting hardware. Consider proper clearance for cable connections when mounting. NOTE: Cutout dimensions for each particular OMI model are readily available for download from the Support Center-Dimensional Drawings section of the Maple Systems website.
PAGE 11
STEPS: 1. Prepare the clamps for the OMI by inserting the screws into the clamp as shown above. Position the screws so that the ends don’t protrude through the clamp’s hole. 2. Set the OMI in the panel cutout and hold it in place until all clamps are in position. 3. Tighten the screw clamps in an even pattern until all are uniformly snug. Caution: Do not over-tighten the screws beyond snugness or you may damage the housing.
PAGE 12
Ethernet To connect your OMI to your computer via the10/100 Base-T Ethernet port requires a standard Ethernet crossover cable (Maple P/N 74310104). If you use a switch or router between the computer and the OMI, use a straight-thru cable (Maple P/N 7431-0103). Once a connection is made, you will need to install a data synchronization program use as Microsoft's ActiveSync onto your computer. ActiveSync provides the ability to manually transfer files to the OMI5000 or download application software.
PAGE 13
Fusing Requirements If the display does not come on within two seconds of power up, remove power. An internal fuse will prevent damage if the polarity of the DC power is incorrect. Check wiring to insure proper connections and try to power up again. Serial Port Connections The diagrams below indicate the proper pin connections for the serial ports of the OMIs.
PAGE 14
COM1 [RS-485 2/4 W] Port, COM3[RS-485] Port Pin out of DE9S (female) connector Pin# 1 2 3 4 5 6 7 8 9 COM1 [RS-485 2W] TX/RX TX/RX + 1010-1017 Rev.
PAGE 15
PAGE 16
Maple Systems Inc. th 808 134 Street SW, Suite 120 Everett, WA 98204-7333 Phone: (425) 745-3229 Email: maple@maplesystems.com Web: www.maplesystems.com © 2012 Maple Systems Inc. All rights reserved.