User's Manual

Step 3: Using Keyless Entry System
Opening and Closing a Garage Door
Light Function (Switching any other devices)
Changing the PIN
Storing more than 1 Code to Control more than 1
Garage Door Opener
Storing more than 1 PIN for Same Code
Switching On the Keypad Illumination
Clearing the Memory
Replacing the Batteries (fig. 3)
Enter 4-digit PIN (programmed in Step 1) followed by pressing
the ENTER button. Garage door will begin moving.
Keyless Entry System will remain active and LED will flash for
approximately 18 seconds after pressing the ENTER button.
During this time, the garage door can be stopped by pressing
any button (except the LIGHT button).
Under certain conditions, your garage door may require
constant pressing of a button to operate. In this case, enter
your 4-digit PIN then press and hold the ENTER button.
Garage door will run as long as the ENTER button is held.
To turn on any other device (e.g. a yard light), press the LIGHT
button followed by pressing the ENTER button.
Press and hold "button 0" on the keypad for 3 seconds until the
LED on the keypad blinks rapidly.
The Keyless Entry System may be used to control up to 3
different garage door openers, each with a different code.
It is possible to store up to 3 different PINs for the same code
for use by different individuals.
Press the LIGHT button. The keypad illumination turns on for 5
seconds.
Press and hold the LIGHT button on the keypad for 3 seconds
until the LED on the keypad blinks rapidly.
Release the backplate of the Keyless Entry System.
Turn counterclockwise the key on the bottom of the spacer and
remove the Keyless Entry System from the spacer.
Replace the backplate.
The LED on the keypad will illuminate for 2 seconds, then the
Keyless Entry System will shut off and the keypad illumination
will go out. Keyless Entry System is now ready for use again.
Enter the PIN which is to be changed followed by pressing the
ENTER button.
Enter the PIN 9-9-9-9.
Remove old batteries.
Release LIGHT button. The memory is cleared. The LED on
the keypad will illuminate for 2 seconds.
Replace with 2 new 3V batteries, CR 2032. Match polarity
designation. Test operability. (Keyless Entry System is
designed to remember all previously programmed codes and
PINs while battery is being replaced).
Note: After clearing the memory, the Keyless Entry System is
programmed with 1 random code and the PIN 1-2-3-4.
For protection of keypad, keep cover closed when not in use.
The Keyless Entry System is now ready for use again with the
new pin (Old PIN is no longer valid).
Enter the new 4-digit PIN followed by pressing the ENTER
button. The LED on the keypad will turn on (no flashing) for 2
seconds.
To use Keyless Entry System with the newly stored temporary
PIN, enter the 4-digit temporary PIN followed by pressing the
ENTER button. This can be done 3 times, after which the
temporary PIN will be automatically erased.
To turn off any other device (e.g. a yard light), press the LIGHT
button followed by pressing the ENTER button once again.
For each of the 3 codes, follow the same steps as shown in
Step 1, with one exception: you must enter in a different PIN
for each code. Each code requires a unique PIN.
To use the Keyless Entry System to open or close a specific
door, simply enter the corresponding PIN for that door followed
by pressing the ENTER button.
Note: If a PIN with more than 4 digits is entered, the Keyless
Entry System considers the last 4 digits.
If an invalid PIN is entered 3 times in a row, the Keyless Entry
System automatically shuts off to prevent tampering or
unauthorized use. After 2 minutes, the Keyless Entry System
can be used again.
FCC Certified: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate the equipment.
67356 2003 All rights reserved. 09/03 ©
Wireless Keyless Entry System
Instructions
(continued)
Enter a temporary 4-digit PIN of your choice followed by the
ENTER button.
Storing a Temporary PIN
A temporary PIN can be stored which will permit operation for 3
times only.
Press and hold "button 1" on the keypad for 3 seconds until the
LED on keypad blinks rapidly. Enter your original PIN followed
by the ENTER button.
Step 2: Keyless Entry System Mounting (fig. 2)
Snap the Keyless Entry System into the spacer.
Turn clockwise the key on the bottom of the spacer using a
coin to lock the Keyless Entry System.
Choose location for mounting your Keyless Entry System.
Using mounting holes at top and bottom of the spacer as a
guide, mark hole locations and then drill two 1/16” pilot holes.
Secure spacer to the mounting surface with the (2) 1/8” x 1-
3/8” screws provided. For mounting surfaces that are not
made of wood, alternate anchoring means may be needed.
For each separate PIN, follow the same steps as shown in
Step 1. Repeat the procedure for each PIN, using the same
transmitter each time. This will store the same code under 3
different PINs.