Instructions / Assembly

23
Fig. 49
Fig. 50
To test, enter the temporary PIN, then press the ENTER
button. The garage door operator will activate. If the
temporary PIN was set for a number of openings, the test
will use up one opening programmed PIN.
NOTE:
To clear the temporary PIN, repeat steps 1-3
above, setting the number of openings to “0” in step 4.
CHANGE AN EXISTING PIN
 Press button for at least 3 seconds, LED’s will flash slowly.
Release button.
 Enter the programmed PIN that you want to change.
Press the ENTER button. LED’s will flash rapidly.
 Enter the new 4-digit PIN of your choice # # # # then press the
ENTER button. LED’s and keypad light up for 2 seconds.
 To test WKE, enter the new PIN then press the ENTER button.
The garage door opener will activate.
PROGRAM A TEMPORARY PIN
A temporary 4-digit PIN can be programmed to allow access to visitors.
Each programmed PIN can program one temporary PIN. The temporary
PIN can be set for a number of door openings (max 99). The temporary
PIN cannot be the same as any previously programmed PIN.
 Press button for at least 3 seconds.
LED’s will flash slowly for 10 seconds.
NOTE: To successfully establish a temporary pin, steps 2-4 must be
completed within 10 seconds after programming activation.
 Enter any programmed PIN, then press ENTER button.
LED’s will flash rapidly.
 Enter the temporary 4-digit PIN of your choice # # # # then press
the ENTER button. LED’s will flash very rapidly.
 Press the number of openings the temporary PIN will work
(up to 99). Then press the ENTER button.
LED’s and key pad buttons light up for 2 seconds then
system goes in stand-by mode.
INSTALLATION
 Select a location to mount the Keyless Entry at a minimum
height of 5 feet (1.5m) out of the reach of children.
 Use mounting plate as template, mark hole location
and then drill two 1/8 inch (3.2mm) pilot holes.
 Secure plate to the mounting surface with the (2)
screws provided. Do not over-tighten screws to avoid
cracking the plastic.
 Cover batteries with battery cover.
 Snap WKE into the mounting plate and secure with
screw provided. See Fig. 49.
 Install slide-up protective cover. Align cover slides with
slide grooves on WKE and slide cover down until it locks.
CLEARING WKE Memory
 Remove Wireless Keyless from wall mounting plate.
 Remove batteries from Wireless Keyless.
 Press and hold ENTER button.
 Install batteries back. Match polarity designation.
 Release ENTER button, LED flash rapidly
approximately 5 seconds.
To prevent possible SERIOUS INJURY or DEATH:
NEVER allow small children near batteries.
If battery is swallowed, immediately notify doctor.
Low Battery Indicator:
Replace the batteries (AAA) when all the keypad buttons start to
flash (10 seconds) upon raising the Wireless Keyless protective cover.
Mounting Plate
Mounting
Screw (2) 4x35
Security
Screw 3x10
Slider
Battery Cover
Wireless Keyless
Entry System
14. OPERATION OF YOUR OPERATOR
BATTERY
WIRELESS KEYLESS ENTRY SYSTEM
The garage door operator activates when the PIN and ENTER
button are pressed. The keypad will blink for 28 seconds, during
that time the ENTER button can be used to stop, start,
reverse the door.
If the wrong number is accidentally pressed, press the correct PIN
then the ENTER button. The Keyless Entry will transmit only
the last four digits.
To deactivate the one button close feature:
 Press the button for 3 seconds. LED on keypad flash slowly.
 Press the ENTER button.
 The keypad LED’s light up for 2 seconds indicating that
the one button close feature has been deactivated.
To activate the one button close feature:
 Press the button for 3 seconds. LED on keypad flash slowly.
 Press the ENTER button.
 The keypad LED’s light up for 2 seconds indicating that
the one button close feature has been activated.
ONE-BUTTON-TO-CLOSE: The Keyless Entry has a feature that
allows the door to be closed using the ENTER button instead of a PIN.
NOTE: Factory setting-active.
The garage door operator can be activated through the following
accessories: