Contents Connections Playback Settings Tips Appendix .
Contents Connections Playback Settings 8 9 9 10 10 13 17 18 18 23 27 31 Accessories Inserting the batteries Operating range of the remote control unit Features High quality sound High performance Easy operation Part names and functions Front panel Display Rear panel Remote control unit Front panel Display Rear panel Appendix Connecting a TV Connection 1 : TV equipped with an HDMI connector and compatible with the ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel) Connection 2 : TV eq
Contents Connections Playback Settings Playback Basic operation Turning the power on Selecting the input source Adjusting the volume Turning off the sound temporarily (Muting) Playback a DVD player/Blu-ray Disc player Playing a USB memory device Playing files stored on USB memory devices Listening to music on a Bluetooth device Playing music from Bluetooth device Pairing with other Bluetooth devices Reconnecting to this unit from a Bluetooth device Listening to audio on Bluetooth headphones Listening to
Contents Connections Playback Convenience functions Adding to HEOS Favorites Playing back HEOS Favorites Deleting a HEOS Favorites Adjusting the volume of each channel to match the input source (Channel Level Adjust) Adjusting the tone (Tone) Displaying your desired video during audio playback (Video Select) Adjusting the picture quality for your viewing environment (Picture Mode) Playing the same music in all zones (All Zone Stereo) Changing the speaker settings to match the listening environment (Speak
Contents Connections Playback Settings Settings Front panel Inputs Input Assign Source Rename Hide Sources Source Level Speakers Audyssey® Setup Procedure for speaker settings (Audyssey® Setup) Error messages Retrieving Audyssey® Setup settings Manual Setup Amp Assign Speaker Config.
Contents Connections Playback 246 246 246 247 249 251 251 252 252 253 253 253 254 254 254 255 258 258 258 259 260 261 264 266 266 267 267 Network Information Connection Wi-Fi Setup Settings Network Control Friendly Name Diagnostics AirPlay HEOS Account You have not signed in You have already signed in General Language Bluetooth Transmitter ZONE2 Setup / ZONE3 Setup Zone Rename Smart Select Names Trigger Out 1 / Trigger Out 2 Auto Standby Front Display Firmware Information Usage Data Save & Load Setup Loc
Contents Connections Playback Settings Tips Appendix Appendix Tips Troubleshooting Power does not turn on / Power is turned off Operations cannot be performed through the remote control unit Display on this unit shows nothing No sound comes out Desired sound does not come out Sound is interrupted or noise occurs No video is shown on the TV The menu screen is not displayed on the TV The color of the menu screen and operations content displayed on the television is different from normal AirPlay cannot
Contents Connections Playback Settings Tips Appendix Thank you for purchasing this Marantz product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference. Accessories . Check that the following parts are supplied with the product.
Connections Contents Playback Settings Inserting the batteries 1 Tips Appendix NOTE 0 To prevent damage or leakage of battery fluid: 0 Do not use a new battery together with an old one. 0 Do not use two different types of batteries. 0 Remove the batteries from the remote control unit if it will not be in use for long periods. 0 If the battery fluid should leak, carefully wipe the fluid off the inside of the battery compartment and insert new batteries.
Contents Connections Playback Settings Tips Appendix Features 0 DTS:X (v p. 318) High quality sound This unit is equipped with the DTS:X decoder technology. DTS:X brings the home theater experience to new heights with its immersive object based audio technology which removes the bounds of channels. The flexibility of objects allows for sound to be scaled large or small and moved around the room with greater accuracy than ever before leading to a richer immersive audio experience. 0 Advanced 11.
Contents Connections Playback Settings Tips 0 Audyssey LFC™ (Low Frequency Containment) (v p. 191) Audyssey LFC™ solves the problem of low frequency sounds disturbing people in neighboring rooms or apartments. Audyssey LFC™ dynamically monitors the audio content and removes the low frequencies that pass through walls, floors and ceilings. It then applies psychoacoustic processing to restore the perception of low bass for listeners in the room.
Contents Connections Playback Settings Tips Appendix 0 Auro-3D This unit is equipped with an Auro-3D decoder. With Auro-3D, Front Height (FHL + FHR), Surround Height (SHL + SHR) and Top Surround (TS/optional) are added to a conventional 5.1-channel system to achieve a natural and realistic sound field that is three-dimensional and fully immersive. You will be able to fully enjoy Auro-3D playback if you properly place the speakers for Auro-3D.
Contents Connections Playback Settings Tips Appendix 0 Digital video processor upscales SD (resolution) or HD (720p/ High performance 1080p) / 4K to 8K 0 Masterful 8K HDMI Connectivity 8K 8K Up to 1080p/4K 60Hz 8K up scaling 8K Ultra HD . This unit includes 8 HDMI inputs and 3 outputs for all your favorite sources. One dedicated 8K HDMI input to support 8K/60Hz and 4K/120Hz passthrough capability, 4:4:4 Pure Color sub-sampling, Dolby Vision, HLG, HDR10, 21:9 video, 3D and BT.
Contents Connections Playback Settings 0 HDMI connections enable connection to various digital AV Tips Appendix 0 The device is equipped with a AirPlay® function in addition to devices (8 inputs, 3 outputs) network functions such as Internet radio etc. (v p. 128) 8 3 Out . . In You can enjoy a wide variety of content, including listening to Internet Radio, playing audio files stored on your PC.
Contents Connections Playback Settings Tips 0 Connect Bluetooth headphones 0 Playback of DSD and FLAC files via USB and networks This unit can transmit Bluetooth so you can enjoy audio wirelessly through your Bluetooth headphones. Playback can be performed using connected speakers and Bluetooth headphones simultaneously, or only using Bluetooth headphones. This unit supports the playback of high resolution audio formats such as DSD (5.6 MHz) and FLAC 192 kHz files.
Contents Connections Playback Settings 0 Multi-Room audio (v p. 139) Appendix 0 Compatible with the “Marantz 2016 AVR Remote” Appz for performing basic operations of the unit with an iPad, iPhone or Android™ devices (Google, Amazon Kindle Fire) 【ZONE2】/【ZONE3】 . 【MAIN ZONE】 Tips . Along with many new features, the graphics and user interface have been completely overhauled.
Contents Connections Playback Settings 0 HEOS provides streaming music from your favorite online music Tips Appendix Easy operation sources 0 “Setup Assistant” provides easy-to-follow setup instructions First select the language when prompted. Then simply follow the instructions displayed on the TV screen to set up the speakers, network, etc. 0 Easy to use Graphical User Interface . This unit is equipped with a Graphical User Interface for improved operability.
Contents Connections Playback Settings Tips Appendix Part names and functions Front panel e r For details, see the next page. Front panel t y u .
Contents Connections qw e r t Playback Settings y Tips Appendix C INPUT SELECTOR knob This selects the input source. (v p. 91) D Main display This displays various pieces of information. (v p. 23) E Remote control sensor This receives signals from the remote control unit. (v p. 9) . F VOLUME knob This adjusts the volume level. (v p. 92) G Door When you are using buttons and/or connectors behind the door, press the bottom of the door to open it.
Contents Connections Playback Settings e r t y u Appendix C M-DAX button/indicator This enables the M-DAX mode. (v p. 186) This lights when the M-DAX mode is selected. With the door open qw Tips io D Dynamic Volume button (DYNAMIC VOL) This switches the Dynamic Volume settings. (v p. 191) E Sub display This displays various pieces of information. (v p. 25) F BACK button This returns to the previous screen. G Cursor buttons (uio p) These select items.
Contents Connections Playback Settings Tips Appendix M Information button (INFO) This displays the status information on the TV screen. (v p. 265) N SLEEP button This sets the sleep timer. (v p. 158) Q0 Q1 O HDMI OUT button This sets the HDMI monitor output. (v p. 196) Q2 Q3 Q4 Q5 Q6 Q7 P DIMMER button Each press of this switches the brightness of the display. (v p. 260) . Q STATUS button Each press of this switches the status information that is shown on the display.
Contents Connections Playback Settings Tips Appendix U Headphones jack (PHONES) This is used to connect headphones. When the headphones are plugged into this jack, audio will no longer be output from the connected speakers or from the PRE OUT connectors. Q8 Q9 W0 NOTE 0 To prevent hearing loss, do not raise the volume level excessively when using headphones. W2 W3 W4 W5 V SETUP MIC jack This is used to connect the supplied Sound calibration microphone. (v p.
Contents Connections Playback Settings Tips Appendix Display o Main display The input source name, sound mode, setting values and other information are displayed here. n Tuner display n Standard display These light up according to the reception conditions when the input source is set to “Tuner”. rt . q w e Front panel Display Rear panel . A Light illumination When the power to this unit is switched on, the surrounding area is lit blue.
Contents Connections Playback Settings n Sleep timer indicator Tips Appendix n ZONE2/ZONE3 power on display . u i . y G This lights up when ZONE2 (another room) power is turned on. (v p. 172) F This lights when the sleep mode is selected. (v p. 158) H This lights up when ZONE3 (another room) power is turned on. (v p.
Contents Connections Playback Settings Tips Appendix o Sub display w e r Q2 E Monitor output indicator These light according to the HDMI monitor output setting. When set to “Auto(Dual)”, the indicators light according to connection status. C Audyssey® indicator This lights when “MultEQ® XT32”, “Dynamic EQ”, “Dynamic Volume” or “Audyssey LFCTM” has been set up. (v p.
Contents Connections Playback Settings . When playing HD Audio sources, the A indicator lights when a signal from an extension channel (a channel other than the front, center, surround, surround back, front height, front wide or LFE channel) is input. Q1 Q2 G Sleep timer indicator This lights when the sleep mode is selected. (v p. 158) H MUTE indicator This blinks while the sound is muted. (v p.
Contents Connections Playback e r ty u i Settings Tips Appendix Rear panel . qw Q2 Q3 o Q4 q Q1 Q0 Q5 Q6 Q7 For details, see the next page.
Contents Playback r Settings D RS-232C connector Used to connect home automation controller devices fitted with RS-232C connectors. Consult the owner’s manual of the home automation controller for more information about serial control of this unit. Perform the operation below beforehand. A Place the external antennas for Bluetooth/wireless connectivity evenly over the screw terminal of rear. B Turn clockwise until the antennas is fully connected. C Rotate the antenna upwards for best reception.
Contents yu i o Playback Q0 Settings Tips J HDMI connectors Used to connect devices equipped with HDMI connectors. 0 “Connection 1 : TV equipped with an HDMI connector and compatible with the ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel)” (v p. 72) 0 “Connection 2 : TV equipped with an HDMI connector and incompatible with the ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel)” (v p. 73) 0 “Connecting a set-top box (Satellite tuner/cable TV)” (v p.
Contents Connections Playback Settings Tips Appendix O BALANCED XLR PRE OUT connectors Used to connect a power amp with BALANCED XLR input connectors. (v p. 44) P UNBALANCED RCA PRE OUT connectors Used to connect a power amp with UNBALANCED RCA input connectors. (v p. 46) . Q2 Q3 Q4 Q5 Q6 Q Component video connectors (COMPONENT VIDEO) Used to connect devices equipped with component video connectors. 0 “Connection 3 : TV equipped without an HDMI connector” (v p.
Contents Connections Playback Settings Tips Appendix Remote control unit A Operation mode indicators The “AVP” operation mode indicator lights when the unit is being operated. The “DEV.” indicator lights when an external device is being operated. The “TV” indicator lights when the TV is being operated. q w e B AVP operation buttons (AVP CONTROL MAIN, Z2, Z3) These switch the zone (MAIN ZONE, ZONE2, ZONE3) that is operated through the remote control unit. 0 “Playback in ZONE2/ZONE3” (v p.
Contents Connections Playback Settings Tips Appendix E Channel/page search buttons (CH/PAGE df) These select radio stations registered to presets or switch pages. (v p. 109) F SLEEP button This sets the sleep timer. (v p. 158) G Information button (INFO) This displays the status information on the TV screen. (v p. 265) H Cursor buttons (uio p) These select items. I BACK button This returns to the previous screen.
Contents Connections Playback Settings Tips Appendix L SMART SELECT buttons (1 - 4) These call up settings registered to each button, such as input source, volume level and sound mode settings. (v p. 160) Q5 M SOUND MODE buttons These select the sound mode. (v p. 141) Q6 Q7 N Number buttons These enter numbers into the unit. (v p. 106) O Remote control signal transmitter This transmits signals from the remote control unit. (v p. 9) P POWER button (X) This turns the power on/off.
Contents Connections Playback Settings Tips Appendix S VOLUME buttons (df) These adjust the volume level. 0 “Adjusting the volume” (v p. 92) 0 “Adjusting the volume (ZONE2/ZONE3)” (v p. 173) T MUTE button (:) This mutes the output audio. 0 “Turning off the sound temporarily (Muting)” (v p. 92) 0 “Turning off the sound temporarily (Muting) (ZONE2/ ZONE3)” (v p. 173) U OPTION button This displays the option menu on the TV screen. V SETUP button This displays the menu on the TV screen. (v p.
Contents Connections Playback Settings o Contents Tips Appendix o Cables used for connections 44 Connecting a TV 71 Connecting a playback device 75 Connecting a USB memory device to the USB port 82 Connecting FM/AM antennas 83 Connecting to a home network (LAN) 85 Connecting an external control device 87 Connecting the power cord 89 Speaker cable . Connecting a power amp Provide necessary cables according to the devices you want to connect. Subwoofer cable . 36 HDMI cable .
Contents Connections Playback Settings Tips Appendix Speaker installation Determine the speaker system depending on the number of speakers you are using and install each speaker and subwoofer in the room. Speaker installation is explained using this example of a typical installation. FL SL SW2 SR SW1 SB SBR . SBL Front panel Display Rear panel Place the FRONT left and right speakers an equal distance from the main listening position.
Contents RHL Connections TRL TML TFL FHL TRR TMR TFR Playback Settings Tips Appendix Place the FRONT HEIGHT left and right speakers FHL/FHR directly above the front speakers. Mount them as (Front height speaker close to the ceiling as possible and aim them left/right): towards the main listening position.
Contents Connections Playback Settings TS FHL SHL FHR FL SW C SR Front panel Appendix SHL/SHR (Surround height speaker left/right): Place the SURROUND HEIGHT left and right speakers directly above the surround speakers. TS (Top surround speaker): Place the TOP SURROUND speaker directly above the main listening position and aligned with the center channel speaker.
Contents Connections FDL Playback Settings Tips About Dolby Atmos Enabled speakers Dolby Atmos Enabled speakers reflect the sound off the ceiling to allow the sound to come from over your head by using a special upwardpointing speaker that is placed on the floor. You can enjoy the Dolby Atmos 3D sound even in an environment where speakers cannot be installed on the ceiling. FDR SDL SDR BDR . BDL Place the FRONT Dolby Atmos Enabled speaker FDL/FDR on the front speaker.
Contents Connections Playback Settings Tips Appendix Height speakers layout 0 This unit is compatible with Dolby Atmos and DTS:X which offers an even wider and deeper surround sensation. 0 The “Speaker Virtualizer” must be set to “On” for Dolby Atmos playback with 5.1channel speaker configurations or less. (v p. 182) 0 IMAX DTS:X / DTS:X can be selected regardless of the speaker configuration. 0 Auro-3D recommends adding FRONT HEIGHT and SURROUND HEIGHT speakers to a 5.1 speaker configuration.
Contents Connections Playback Settings o When 7.1-channel speakers are installed using surround back speakers Tips Appendix o When 5.1-channel speakers are installed FR FL FR FL SW SW C z1 z2 z1 z2 z3 SL C SL SR . SR Listening position z1 22° - 30° z2 120° SBR . SBL z1 22° - 30° z2 90° - 110° z3 135° - 150° 0 When using a single surround back speaker, place it directly behind the listening position.
Contents Connections Playback Settings o Layout including height speakers and ceiling speakers Tips Appendix n Ceiling speaker layout example Combination of 5.1-channel layout and top front/top rear speakers. n Height speaker layout example TRL TRR TFL Combination of 5.1-channel layout and front height/rear height speakers. TFR FL RHL RHR FHL SW FR C FHR FR C SR . SW .
Contents Connections Playback Settings Tips Appendix n Auro-3D layout example n Dolby Atmos Enabled speaker layout example Combination of 5.1-channel speakers with Front Height/Surround Height/Top Surround speakers. Combination of 5.1-channel layout and front Dolby/surround Dolby speakers. TS FHL SHL FDL SDL FL SW FDR C FL SDR FR SL SW SHR FR C SR SR . .
Contents Connections Playback Settings Tips Appendix Connecting a power amp Before connecting a power amp 0 Connect a power amp (sold separately) to the PRE OUT connector of 0 0 0 1 3 2 . 0 G AV7706 BALANCED XLR PRE OUT connector PIN arrangement H this unit. This unit has UNBALANCED RCA PRE OUT connector and BALANCED XLR PRE OUT connector. Connect to the correct connector for your power amp. If your power amp has both connectors, connect to either of them.
Contents Connections Playback Settings Tips o Example of connections to Marantz MM8077 power amp n Connecting the UNBALANCED RCA PRE OUT connector When using UNBALANCED RCA connectors for connection, set the input change switch to “UNBALANCED” on MM8077. .
Contents Connections Playback Settings Tips n Connecting the BALANCED XLR PRE OUT connector When using BALANCED XLR connectors for connection, set the input change switch to “BALANCED” on MM8077. .
Contents Connections Playback Settings Tips Appendix o About the cable labels (supplied) for channel identification Attach the cable label corresponding to each speaker to each speaker cable. This makes it easier to connect the speakers to the power amp.
Contents Connections Playback Settings Tips Refer to the table and attach the label to each speaker cable. G How to attach the cable labels H Speaker .
Contents Connections Playback Settings Tips Appendix Speaker configuration and “Amp Assign” settings This system configuration plays back 11-channels. You can create speaker systems such as a bi-amp connection by changing the “Amp Assign” settings. Perform “Amp Assign” settings to suit the number of rooms and speaker configuration to be installed. (v p. 226) Playback speaker in MAIN ZONE 5.1-channel playback 7.1-channel playback 9.1-channel playback 11.1-channel playback 9.
Contents Connections Playback Settings Refer to the example connection for “Example connection for the Auro-3D 9.1-channel system” (v p. 62) when playing Auro-3D with a 9.1channel system using the basic 5.1-channel system and the front height and surround height speakers. Also refer to the connection example for “Example connection for the Auro-3D 10.1-channel system” (v p. 66) when playing Auro-3D with a 10.1-channel system by adding the top surround speaker.
Contents Connections Playback Settings Tips Appendix Up to 11.2-channels can be connected by using either UNBALANCED RCA connectors or BALANCED XLR connectors. This example explains how to make a connection when using UNBALANCED RCA connectors. Connecting 5.1-channel speakers This serves as a basic 5.1-channel surround system.
Contents Connections Playback Settings Tips Appendix Connecting 7.1-channel speakers o Example connections when using surround back speakers This 7.1-channel surround system is the same as a basic 5.1-channel system but with surround back speakers. FL FR 【 MM8077 】 SW C SL CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) SR SBR .
Contents Connections Playback Settings Tips Appendix o Example connections when using ceiling speakers This 7.1-channel surround system is the same as a basic 5.1-channel system but with ceiling speakers. TML TMR FL SL 【 MM8077 】 FR SW C SR CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) .
Contents Connections Playback Settings Tips Appendix o Example connections when using height speakers This 7.1-channel surround system is the same as a basic 5.1-channel system but with front height speakers. FHL FHR FL FR 【 MM8077 】 SW C SL CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) UNBALANCED BALANCED .
Contents Connections Playback Settings Tips Appendix o Example connections when using Dolby Atmos Enabled speakers This 7.1-channel surround system is the same as a basic 5.1-channel system but with front Dolby speakers. FDL SL FL SW 【 MM8077 】 FDR C FR SR CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) . UNBALANCED BALANCED .
Connections Contents Playback Settings Tips Appendix Connecting 9.1-channel speakers This system, which is based on a 5.1-channel system, plays back up to 9.1-channels at the same time.
Connections Contents Playback Settings Tips Appendix o Example connection when using two sets of ceiling speakers TRL TRR TFL TFR FL FR SW C SR 【 MM8077 】 CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALANCED (C)
Connections Contents Playback Settings Tips Appendix o Example connection when using one set of height speakers FHL FHR FL SL FR SW C SBL SR 【 MM8077 】 CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALANCED (C) BAL
Connections Contents Playback Settings Tips Appendix o Example connection when using two sets of height speakers RHL FHL FHR FL FR SW C SR 【 MM8077 】 CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALANCED (C) BALANC
Connections Contents Playback Settings Tips Appendix o Example connection when using one set of Dolby Atmos Enabled speakers FDL SL FL SW FDR C SBL FR SR 【 MM8077 】 CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALA
Connections Contents Playback Settings Tips Appendix o Example connection when using two sets of Dolby Atmos Enabled speakers FDL SDL FL SW FDR C 【 MM8077 】 SR CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALANCED (
Connections Contents Playback Settings Tips Appendix o Example connection for the Auro-3D 9.1channel system This speaker configuration is optimized for Auro-3D playback.
Connections Contents Playback Settings Tips Appendix Connecting 11.1-channel speakers This system, which is based on a 5.1-channel system, plays back up to 11.1-channels at the same time.
Connections Contents Playback Settings Tips Appendix o Example connection when using two sets of height speakers RHL FHL FHR FL SL RHR FR SW C SBL SR 【 MM8077 】 CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 UNBALANC
Connections Contents Playback Settings Tips Appendix n Example connection when using two sets of Dolby Atmos Enabled speakers FDL SDL FL SW FDR C FR SDR 【 MM8077 】 SL SR SBL CHANNEL7 (C) CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL7 (C) SBR CHANNEL6 (SBR) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) CHANNEL5 (SBL) CHANNEL4 (SR) CHANNEL3 (SL) CHANNEL2 (FR) CHANNEL1 (FL) .
Connections Contents Playback Settings Tips Appendix o Example connection for the Auro-3D 10.1channel system This speaker configuration is optimized for Auro-3D playback.
Contents Connections Playback Settings Tips Appendix Channels output from the HEIGHT1, HEIGHT2 RCA connectors and HEIGHT1, HEIGHT2 XLR connectors can be changed to the following patterns according to the speaker systems being used. Set this from “Amp Assign” in the menu. (v p.
Contents Number of height/ ceiling speakers 4 speakers 5 speakers Connections Playback Settings Combination of height speakers to be used Number of Dolby Combination pattern speakers Front Height & Surr. Height None Front Height & Rear Height z Front Height & Surr.
Connections Contents Playback Settings Tips Appendix Connecting 9.1-channel speakers: Bi-amp connection of front speakers This system plays back 9.1-channels. You can use the bi-amp connection for front speakers. Bi-amp connection is a method to connect separate amplifiers to the tweeter terminal and woofer terminal of a speaker that supports bi-amplification.
Connections Contents Playback Settings Tips Appendix Connecting 9.1-channel speakers: Second pair of front speakers This system enables switching playback between front speakers A and B as desired.
Contents Connections Playback Settings Tips Appendix Connecting a TV Connect a TV to this unit so that the input video is output to the TV. You can also enjoy audio from the TV on this unit. How to connect a TV depends on the connectors and functions equipped on the TV. ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel) function plays TV audio on this unit by sending the TV audio signal to this unit via HDMI cable.
Contents Connections Playback Settings Tips Appendix Connection 1 : TV equipped with an HDMI connector and compatible with the ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel) Use an HDMI cable to connect a TV that is compatible with the ARC / eARC function to this unit. Set “HDMI Control” to “On” or “ARC” to “On” when using a TV that supports the ARC function. (v p.
Contents Connections Playback Settings Tips Appendix Connection 2 : TV equipped with an HDMI connector and incompatible with the ARC (Audio Return Channel) / eARC (Enhanced Audio Return Channel) Use an HDMI cable to connect the TV to this unit. To listen to audio from TV on this unit, use an optical cable to connect the TV to this unit. TV IN OPTICAL OUT HDMI IN .
Contents Connections Playback Settings Tips Connection 3 : TV equipped without an HDMI connector Use a component video or a video cable to connect the TV to this unit. To listen to audio from TV on this unit, use an optical cable to connect the TV to this unit. TV OUT OPTICAL OUT IN VIDEO IN COMPONENT VIDEO IN Y PB PR .
Contents Connections Playback Settings Tips Appendix Connecting a playback device This unit is equipped with three types of video input connectors (HDMI, component video and composite video) and three types of audio input connectors (HDMI, digital audio and audio). Select input connectors on this unit according to the connectors equipped on the device you want to connect. If the device connected to this unit is equipped with an HDMI connector, it is recommended to use HDMI connections.
Contents Connections Playback Settings Tips Connecting a set-top box (Satellite tuner/cable TV) This explanation uses the connection with a satellite tuner/cable TV STB as an example. Select the input connectors on this unit to match the connectors on the device that you want to connect to. (HDMI incompatible device) Satellite tuner / Cable TV AUDIO COAXIAL OUT Satellite tuner / Cable TV VIDEO AUDIO OUT R L R L R L VIDEO OUT HDMI OUT .
Connections Contents Playback Settings Tips Connecting a DVD player or Blu-ray Disc player This explanation uses the connection with a DVD player or Blu-ray Disc player as an example. Select the input connectors on this unit to match the connectors on the device that you want to connect to.
Contents Connections Playback Settings Tips Appendix Connecting a player device compatible with the 8K This unit supports 8K HDMI video signals. If your player supports 8K, connect it to the HDMI 7 (8K) connector on your device. 8K player HDMI OUT 0 To enjoy 8K video, connect an 8K-compatible TV with an “Ultra High Speed 48 Gbps HDMI cable”. 0 Set “4K/8K Signal Format” to “8K Enhanced” in the menu to enjoy 8K video. (v p.
Contents Connections Playback Settings Tips Connecting a video camcorder or game console This explanation uses the connection with a video camcorders as an example. Connect a playback device to this unit, such as a video camcorder or game console. (HDMI incompatible device) Video camcorder AUDIO VIDEO AUDIO OUT L R VIDEO OUT R L R HDMI OUT .
Contents Connections Playback Settings Tips Appendix Connecting a turntable This unit is compatible with turntables equipped with a moving magnet (MM) phono cartridge. When you connect to a turntable with a low output moving coil (MC) cartridge, use a commercially available MC head amp or a step-up transformer. If you set this unit’s input source to “Phono” and you accidentally increase the volume without having a turntable connected, you may hear a hum noise from the speakers.
Contents Connections Playback Settings Tips Appendix Connecting a device with a multi-channel output connector You can connect this unit to an external device fitted with multi-channel sound audio output connectors to enjoy music and video. To play analog signals input from 7.1CH IN connectors, set “INPUT MODE” to “7.1CH IN”. (v p. 212) Devices with a multi-channel output connector (Blu-ray Disc player, DVD player, External decoder etc.
Contents Connections Playback Settings Tips Appendix Connecting a USB memory device to the USB port For operating instructions see “Playing a USB memory device” (v p. 93). . USB memory device 0 Marantz does not guarantee that all USB memory devices will operate or receive power. When using a portable USB hard disk drive (HDD) which came with an AC adapter, use that device’s supplied AC adapter. NOTE 0 USB memory devices will not work via a USB hub.
Contents Connections Playback Settings Tips Appendix Connecting FM/AM antennas Connect the antenna, tune in to a broadcast and then move the antenna to the location where there is least noise. Then use tape, etc. to fix the antenna in this location. (“Listening to FM/AM broadcasts” (v p. 105)) AM loop antenna (supplied) 0 If you are unable to receive a good broadcast signal, we recommend installing an outdoor antenna. For details, inquire at the retail store where you purchased the unit.
Contents Connections Playback Settings Tips o AM loop antenna assembly o Using the AM loop antenna 1 Suspending on a wall Suspend directly on a wall without assembling. 2 Put the stand section through the bottom of the loop antenna from the rear and bend it forward. Insert the projecting part into the square hole in the stand. Stand Square hole . Nail, tack, etc. Loop antenna Standing alone Use the procedure shown above to assemble. When assembling, refer to “AM loop antenna assembly”. .
Contents Connections Playback Settings Tips Appendix Connecting to a home network (LAN) This unit can connect to a network using a wired LAN or wireless LAN. You can connect this unit to your home network (LAN) to enable various types of playback and operations as described below.
Contents Connections Playback Settings Wireless LAN Tips Appendix 0 When using this unit, we recommend you use a router equipped with the following functions: When connecting to the network via wireless LAN, connect the external antennas for Bluetooth/wireless connectivity connection to the rear panel and stand them upright. See “Wi-Fi Setup” on how to connect to a wireless LAN router. (v p. 247) 0 Built-in DHCP server This function automatically assigns IP addresses on the LAN.
Contents Connections Playback Settings Tips Appendix Connecting an external control device REMOTE CONTROL jacks o Performing operations by RC on this unit without visual contact o Remotely connecting Marantz devices When you are using a Marantz device other than this unit that supports remote connection, you can transmit remote control signals just by connecting the device to the REMOTE CONTROL IN/OUT connector with a monaural cable.
Contents Connections Playback Settings Tips Appendix DC OUT jacks When a device with DC IN jack is connected, the connected device’s power on/standby can be controlled through linked operation to this unit. The DC OUT jack outputs a maximum 12 V DC/150 mA electrical signal. . 12 V DC/150 mA trigger-compatible device NOTE 0 Use a monaural mini-plug cable for connecting the DC OUT jacks. Do not use a stereo mini-plug cable.
Contents Connections Playback Settings Tips Connecting the power cord After completing all the connections, insert the power plug into the power outlet. Power cord (supplied) .
Contents Connections Playback Settings o Contents Tips Appendix Playback network audio/service Basic operation Turning the power on 91 Selecting the input source 91 Adjusting the volume 92 Turning off the sound temporarily (Muting) 92 Selecting a sound mode Playback a device 92 Playing a USB memory device 93 Listening to music on a Bluetooth device 97 Listening to audio on Bluetooth headphones 102 Listening to FM/AM broadcasts 105 113 Playing back files stored on a PC or NAS 115
Contents Connections Playback Settings Tips Appendix Basic operation Turning the power on 1 POWER X Press POWER X to turn on power to the unit. 0 You can press the input source select button when the unit is in standby mode to turn on the power. 0 You can also switch the power to standby by pressing X on the main unit. Input source select buttons Selecting the input source VOLUME df MUTE : 1 Press the input source select button to be played back.
Contents Connections Playback Settings Adjusting the volume 1 Use VOLUME df to adjust the volume. The following describes the procedure for playing DVD player/Blu-ray Disc player. 1 Turning off the sound temporarily (Muting) 2 3 Press MUTE :. 4 0 “MUTE” appears on the display. 0 : appears on the TV screen. Display Rear panel Prepare for playback. A Turn on the power of the TV, subwoofer and player. B Change the TV input to the input of this unit. Press POWER X to turn on power to the unit.
Contents Connections Playback Settings Tips Appendix Playing a USB memory device 0 Playing back music files stored on a USB memory device. 0 Only USB memory devices conforming to mass storage class standards can be played on this unit. 0 This unit is compatible with USB memory devices in “FAT32” or “NTFS” format. 0 The audio format types and specifications supported by this unit for playback are as follows. See “Playing back a USB memory devices” (v p. 310) for details.
Contents Connections Playback Settings 4 Playing files stored on USB memory devices 2 3 Insert a “FAT32” or “NTFS” formatted USB memory device into the USB port. Appendix Browse the music on your USB memory device and select something to play. 0 When you select something to play you will be asked how you want to queue up your music. Press USB to switch the input source to “USB”. Select the name of this unit.
Contents Playback Settings Tips Operation buttons Use ui to select the “Play Now” or “Play Now & Replace Queue”, then press ENTER. Playback starts. NOW PLAYING Nature Appendix Function 1 Playback 3 Pause 2 Stop 89 Skip to previous track / Skip to next track CH/PAGE d f Switch to the previous page/next page in the list display HOME Go to Home screen Nature 01 - Various Artists 2:45 0 When an MP3 music file includes album art data, the album art can be displayed while playing the file.
Contents Connections Playback Settings Tips o Operations accessible through the option menu 0 “Adjusting the volume of each channel to match the input source (Channel Level Adjust)” (v p. 135) 0 “Adjusting the tone (Tone)” (v p. 136) 0 “Displaying your desired video during audio playback (Video Select)” (v p. 137) 0 “Playing the same music in all zones (All Zone Stereo)” (v p.
Contents Connections Playback Settings Tips Appendix Listening to music on a Bluetooth device Music files stored on Bluetooth devices such as smartphones, digital music players, etc. can be enjoyed on this unit by pairing and connecting this unit with the Bluetooth device. Communication is possible up to a range of about 98.4 ft/30 m. POWER X NOTE 0 To play back music from a Bluetooth device, the Bluetooth device needs to support the A2DP profile. Bluetooth OPTION BACK .
Contents Connections Playback Settings 3 4 Playing music from Bluetooth device In order to enjoy music from a Bluetooth device on this unit, the Bluetooth device must first be paired with this unit. Once the Bluetooth device has been paired, it does not need to be paired again. 1 2 Appendix Activate the Bluetooth settings on your mobile device. Select this unit when its name appears in the list of devices displayed on the screen of the Bluetooth device.
Contents Connections Operation buttons Playback Settings Tips Function 1 Playback 3 Pause 2 Stop 89 Skip to previous track / Skip to next track 0 Press STATUS on this unit during playback to switch the display between Title name, Artist name, Album name, etc.
Contents Connections Playback Settings Pairing with other Bluetooth devices NOTE Activate the Bluetooth settings on your mobile device. Press and hold Bluetooth on the remote control unit for at least 3 seconds. o Operations accessible through the option menu This unit will go into the pairing mode. 3 Select this unit when its name appears in the list of devices displayed on the screen of the Bluetooth device. 0 “Pairing with other Bluetooth devices” (v p.
Contents Connections Playback Settings Tips Reconnecting to this unit from a Bluetooth device After pairing is completed, the Bluetooth device can be connected without performing any operations on this unit. This operation also needs to be performed when switching the Bluetooth device for playback. 1 2 3 4 If a Bluetooth device is currently connected, deactivate the Bluetooth setting of that device to disconnect it. Activate the Bluetooth setting of the Bluetooth device to be connected.
Contents Connections Playback Settings Tips Listening to audio on Bluetooth headphones You can listen to audio playing through the MAIN ZONE of this unit on Bluetooth headphones. Output audio from connected speakers and Bluetooth headphones simultaneously, or only using Bluetooth headphones. (Output Mode: Bluetooth Only) .
Contents Connections Playback Settings Listening to audio on Bluetooth headphones 1 2 NOTE 0 Bluetooth headphones volume cannot be adjusted from this unit. Adjust volume of your Bluetooth headphones. 0 Stereo mode is fixed as the sound mode when using Bluetooth headphones. Any sound modes and other audio settings are not reflected in audio output on Bluetooth headphones.
Contents Connections Playback Settings Reconnecting to a Bluetooth headphones Display Appendix Disconnecting Bluetooth headphones Complete any of the following steps to disconnect your Bluetooth headphones: 0 Turn off your Bluetooth headphones. 0 Go to “Bluetooth Transmitter” and then select “Disconnect” within the options menu. 0 In the setup menu, go to “General” - “Bluetooth Transmitter”, and set “Transmitter” to Off. (v p.
Contents Connections Playback Settings Tips Appendix Listening to FM/AM broadcasts You can use the built-in tuner of this unit to listen to FM broadcasts and AM broadcasts. Make sure the FM antenna and AM loop antenna are connected to this unit first. TUNER CH/PAGE df OPTION uio p ENTER BACK TUNE +, – .
Contents Connections Playback Settings 5 Listening to FM/AM broadcasts 1 2 Connect the antenna. (“Connecting FM/AM antennas” (v p. 83)) 6 Press TUNER to switch the input source to “Tuner”. G TV screen H STEREO OPTION Option . . 4 When listening to an FM broadcast. AM: When listening to an AM broadcast. Press TUNE + or TUNE – to select the station you want listen to.
Contents Connections Playback Settings o Operations accessible through the option menu You can enter the receiving frequency directly to tune in. 0 “Changing the tune mode (Tune Mode)” (v p. 108) 0 “Tuning in to stations and presetting them automatically (Auto Preset 1 Memory)” (v p. 108) 0 “Presetting the current broadcast station (Preset Memory)” (v p. 109) 2 0 “Specify a name for the preset broadcast station (Preset 0 0 0 0 Name)” (v p.
Contents Connections Playback Settings Changing the tune mode (Tune Mode) 2 3 A maximum of 56 radio stations can be automatically preset. Press OPTION when the input source is “Tuner”. 1 The option menu screen is displayed. Use ui to select “Tune Mode”, then press ENTER. 2 Use o p to select the tune mode, then press ENTER. Auto: Automatically search for and tune to a receivable radio station. Manual: Manually change the frequency one step at a time each time the button is pressed.
Contents Connections Playback Settings Presetting the current broadcast station (Preset Memory) 2 3 4 Appendix Channel Default settings 1–8 92.10 / 92.30 / 92.50 / 92.70 / 93.10 / 93.50 / 93.70 / 94.10 MHz 9 – 16 94.30 / 94.50 / 94.70 / 94.90 / 95.10 / 95.30 / 95.50 / 95.70 MHz 17 – 24 Tune in the broadcast station you want to preset. (“Listening to FM/AM broadcasts” (v p. 106)) 98.10 / 98.30 / 98.50 / 98.70 / 98.90 / 99.10 / 100.10 / 100.30 MHz 25 – 32 100.50 / 100.70 / 100.90 / 101.
Contents Connections Playback Settings 5 Specify a name for the preset broadcast station (Preset Name) You can set the name to the preset broadcast station or change it. Up to 8 characters can be input. 1 2 3 4 6 7 Press OPTION when the input source is “Tuner”. The option menu screen is displayed. Use ui to select “Preset Name”, then press ENTER. Tips Use ui to select a name label, then press ENTER. The screen that lets you edit the Preset Name is displayed.
Contents Connections Playback Settings Skipping preset broadcast stations (Preset Skip) 2 3 A Use o p to select the group of broadcast stations you want to skip. B Use ui to select the broadcast station you want to skip. C Use o p to select “Skip”. The station you selected is not displayed. Press OPTION when the input source is “Tuner”. 4 The option menu screen is displayed. Press OPTION to return to the previous screen. Use ui to select “Preset Skip”, then press ENTER.
Contents Connections Playback Settings Tips Cancelling Preset Skip 1 2 3 While the “Preset Skip” screen is displayed, use o p to select a group containing a broadcast station to cancel the skip for. Use ui to select a broadcast station to cancel the skip for. Use o p to select “On”. The skip is cancelled. NOTE 0 “Preset Skip” cannot be cancelled for groups.
Contents Connections Playback Settings Tips Appendix Listening to Internet Radio 0 Internet Radio refers to radio broadcasts distributed over the Internet. Internet Radio stations from around the world can be received. 0 The Internet Radio station list on this unit the database service provided by TuneIn Radio service. 0 The audio format types and specifications supported by this unit for playback are as follows. See “Playing back Internet Radio” (v p. 313) for details.
Contents Connections Playback Settings Listening to Internet Radio 1 0 You can also press R (HEOS Music). Use ui to select “TuneIn NOTE Internet Radio”, then press ENTER. 0 The radio station database service may be suspended or be otherwise unavailable without notice. Select the station you want to play. Operation buttons Appendix 0 The display switches between track title and radio station name etc. each time the main unit’s STATUS is pressed. Press INTERNET RADIO.
Contents Connections Playback Settings Tips Appendix Playing back files stored on a PC or NAS 0 This unit can play back music files and playlists (m3u, wpl) from DLNA compatible servers including PCs and NAS devices on your network. 0 Supported file formats: For details, see “Playing back a file saved on a PC or NAS” (v p. 312). 0 WMA 0 MP3 0 WAV 0 MPEG-4 AAC 0 FLAC (HEOS Music) 0 Apple Lossless 0 DSD CH/PAGE df OPTION uio p ENTER BACK 1 89 3 2 .
Connections Contents Playback Settings 4 Playing back files stored on a PC or NAS Use this procedure to play music files or playlists stored on DLNA files servers on your local network. 1 2 Tips Appendix Browse the music on your PC/NAS and select something to play. 0 When you select something to play you will be asked how you want to queue up your music. Press R (HEOS Music). Use ui to select “Music Servers”, then press ENTER.
Contents 5 Connections Playback Settings Use ui to select the “Play Now” or “Play Now & Replace Queue”, then press ENTER. Tips Appendix 0 The display switches between track title, artist name, and album title each time the main unit’s STATUS is pressed. 0 When a WMA (Windows Media Audio), MP3 or MPEG-4 AAC file includes album art data, the album art can be displayed while the music files are playing. 0 If you use Ver.11 or later of Windows Media Player, the album art for WMA files can be displayed.
Contents Connections Playback Settings Tips o Operations accessible through the option menu 0 “Adjusting the volume of each channel to match the input source (Channel Level Adjust)” (v p. 135) 0 “Adjusting the tone (Tone)” (v p. 136) 0 “Displaying your desired video during audio playback (Video Select)” (v p. 137) 0 “Playing the same music in all zones (All Zone Stereo)” (v p. 139) 0 “Changing the speaker settings to match the listening environment (Speaker Preset)” (v p.
Contents Connections Playback Settings Tips Appendix Getting the HEOS App . You can use many online music streaming services from the HEOS App. Depending upon your geographical location, there are several options to choose from. Download the HEOS App for iOS or Android by searching App Store, Google Play store or Amazon Appstore for “HEOS”.
Contents Connections Playback Settings Tips o Changing your HEOS Account HEOS Account 1 2 HEOS Accounts can be registered in “HEOS Account” (v p. 253) in the menu of this unit or by tapping “Music” tab - “Settings” icon a in the HEOS App. o What is a HEOS Account? 3 4 A HEOS Account is master account or “keychain” for managing all of your HEOS music services with one single username and password. o Why do I need a HEOS Account? Tap the “Music” tab.
Contents Connections Playback Settings Tips Playing from streaming music services Appendix Rooms Drag one room into another to group them A music service is an online music company that provides access to vast music collections via free and/or paid subscriptions. Depending upon your geographical location, there are several options to choose from. Dining L + Dining R Song Name 1 Kitchen Song Name 2 NOTE 0 The HEOS App and brand is not affiliated with any manufacturer of any mobile device.
Contents Connections Playback Settings Tips o Selecting the music track or station from music sources Music Tap the “Music” tab and select a music source. 0 All music services displayed may not be available in your location. This Phone Music Servers Playlists Rooms USB Music History Music Now Playing .
Contents Playback Settings Tips Browse the music to play. Now Playing Album After selecting a music track or radio station the app will automatically change to the “Now Playing” screen. Album 10 Tracks,60 Mins.,2014 Track 01 Rooms 0 When you select a music track to play you will be asked how you want to queue up your music. Play Now: Inserts the item into the queue after the currently playing track and plays the selected item immediately.
Contents Connections Playback Settings Listening to the same music in multiple rooms Rooms Rooms Drag one room into another to group them Drag one room into another to group them 3 Dining Song Name 1 Song Name 1 2 Living 1 Kitchen Living+Kitchen Song Name 2 Song Name 2 3 Living Kitchen Bedroom o Grouping rooms Drag a room out of this group to ungroup it Song Name 3 Bedroom Song Name 3 Press and hold your finger on room that is not playing music. Rooms Music Now Playing Rooms .
Contents Connections Playback Settings Tips o Ungrouping rooms 1 2 Press and hold your finger on room that you want to remove from the group. Appendix Rooms Rooms Drag one room into another to group them Drag one room into another to group them Dining Dining Song Name 1 Drag it out of the group and lift your finger. Song Name 1 Living Living Song Name 2 NOTE Song Name 2 Living 0 You can not remove the first room that started playing the music before grouping.
Contents Connections Playback Settings o Grouping all rooms (party mode) Rooms You can easily group 16 rooms together into Party Mode by using a "pinch" gesture. Drag one room into another to group them Dining 1 Appendix Rooms Drag one room into another to group them Place two fingers on the screen over the list of rooms. Song Name 1 Living Dining Song Name 2 Quickly pinch your two fingers together and release.
Contents Connections Playback Settings o Ungrouping all rooms You can easily ungroup all of your rooms and exit Party Mode by using a "spread" gesture. 2 3 Rooms Rooms Drag one room into another to group them Dining Song Name 1 Place two fingers close together on the screen over list of rooms. 1 2 Song Name 1 Living Song Name 2 Living 3 Kitchen Song Name 3 Kitchen Bedroom Bedroom All of your rooms will be ungrouped.
Contents Connections Playback Settings Tips Appendix AirPlay function Music files stored on your iPhone, iPod touch, iPad or iTunes can be played on this unit via the network. 0 0 0 0 0 PC Router Source input will be switched to “HEOS Music” when AirPlay playback is started. You can stop AirPlay playback by choosing other input source. To see song and artist names together, press STATUS on the main unit. For information about how to use iTunes, also see the Help for iTunes.
Contents Connections Playback Settings Playing songs from your iPhone, iPod touch or iPad 1 2 Connect your iPhone, iPod touch or iPad Wi-Fi to the same network as this unit. 0 For details, see your device’s manual. Turn this unit ON. Set “Network Control” to “Always On” for this unit. (v p. 251) NOTE Play the song on your iPhone, iPod touch or iPad. 0 When “Network Control” is set to “Always On”, the unit consumes more standby power.
Contents Connections Playback Settings 2 NOTE 0 In playback using the AirPlay function, the sound is output at the iPhone, iPod touch, iPad or iTunes volume setting level. You should turn down the iPhone, iPod touch, iPad or iTunes volume prior to playback and then adjust it to a suitable level. Play a song from your iPhone, iPod touch or iPad on multiple synced devices (AirPlay 2) Tap the AirPlay icon. Displays a list of devices/speakers that can be played back on the same network.
Contents Connections Playback Settings Tips Appendix Spotify Connect function Spotify is all the music you’ll ever need. Millions of songs available instantly. Just search for the music you love, or let Spotify play you something great. Spotify works on your phone, tablet, computer and home speakers. So you’ll always have the perfect soundtrack for whatever you’re doing. Now you can enjoy Spotify with your free account as well as Premium account.
Contents Connections Playback Settings Tips Appendix Convenience functions This section explains how to use convenient functions that can be used for each input source. These functions can only be set in the MAIN ZONE. (HEOS Music) OPTION .
Contents Connections Playback Settings 1 2 While content is playing, press OPTION. The option menu screen is displayed. Use ui to select “Add to HEOS Favorites”, then press ENTER. Press R (HEOS Music). Use ui to select “HEOS Favorites”, then press ENTER. MUSIC TuneIn Internet Radio HEOS Favorites Music Servers USB Music . 2 Appendix Playing back HEOS Favorites Adding to HEOS Favorites 1 Tips 3 Front panel Display Rear panel 133 Browse the content and select something to play.
Contents Connections Playback Settings Tips Deleting a HEOS Favorites 1 2 While the HEOS Favorites content list is displayed, use ui to select the item you want to remove from HEOS Favorites, then press OPTION. Use ui to select “Remove from HEOS Favorites”, then press ENTER.
Contents Connections Playback Settings 4 Adjusting the volume of each channel to match the input source (Channel Level Adjust) 2 Use o p to adjust the volume. 5 Press OPTION. Use uio p to select “Exit”, then press ENTER. 0 Select “Reset” and press ENTER if you want to restore the adjustment values of the various channels to “0.0 dB” (Default). 0 Headphone volume can be adjusted when a headphone is connected. 0 “Channel Level Adjust” settings are stored for each input source.
Contents Connections Playback Settings 4 Adjusting the tone (Tone) Adjusts the tonal quality of the sound. 1 2 3 Press OPTION. An option menu screen is displayed. 0 When the input source is “HEOS Music”, an option menu for online music is displayed. Select “AVP Options…”, then press ENTER. 5 Tips Appendix Select “On” in step 3 and press i to select the sound range to be adjusted. Bass: Adjust bass. Treble: Adjust treble. Use o p to adjust the tone, then press ENTER.
Contents Connections Playback Settings 4 Displaying your desired video during audio playback (Video Select) 5 This unit can display video from a different source on TV during audio playback. You can set this for each input source. Tips If you selected “On” in step 3, press i and select “Source”. Use o p to select the input source for video you want to play back, then press ENTER. n Supported input sources: CDz / Tuner / HEOS Music / Phono 0 “Video Select” settings are stored for each input source.
Contents Connections Playback Settings 3 Adjusting the picture quality for your viewing environment (Picture Mode) n Supported input sources : CBL/SAT / DVD / Blu-ray / Game / AUX / Media Player / CDz / TV Audioz z You can set the picture mode when an HDMI, component video or video connector is assigned and “i/p Scaler” is set to anything other than “Off”. (v p. 202) 1 2 Press OPTION. An option menu screen is displayed. Use ui to select “Picture Mode”, then press ENTER.
Contents Connections Playback Settings 1 You can play back the music being played back in MAIN ZONE simultaneously in ZONE2 and ZONE3 (another rooms). It is useful when you want to enjoy the same music at the same time in multiple rooms during home party or when you want to play back the same background music in the entire house. 2 3 2 3 An option menu screen is displayed. 0 When the input source is “HEOS Music”, an option menu for online music is displayed. Select “AVP Options…”, then press ENTER.
Contents Connections Playback Settings Tips Changing the speaker settings to match the listening environment (Speaker Preset) Two speaker settings can be saved to suit the environments where you use your speakers. 1 2 3 Press OPTION. An option menu screen is displayed. 0 When the input source is “HEOS Music”, an option menu for online music is displayed. Select “AVP Options…”, then press ENTER. Use ui to select “Speaker Preset”, then press ENTER. The “Speaker Preset” screen is displayed.
Contents Connections Playback Settings Tips Appendix Selecting a sound mode This unit allows you to enjoy various kinds of surround and stereo playback modes. Disc formats such as Blu-ray Disc and DVD, as well as being supported by digital broadcasting, and even by streaming movies and music from internet-based subscription services. This unit supports playback of almost all of these multi-channel audio formats.
Contents Connections Playback Settings 0 Press MOVIE, MUSIC or GAME to display a list of the sound modes that can be selected. Each time you press MOVIE, MUSIC or GAME, the sound mode changes. 0 While the list is displayed, you can also use ui to select a sound mode. 0 Try out various sound modes and enjoy sound mode in your favorite mode. Press MOVIE, MUSIC or GAME to select a sound mode. MOVIE : Switches to the sound mode suitable for enjoying movies and TV programs.
Contents Connections Playback Settings Direct playback Appendix Pure Direct playback Sound recorded in source is played as is. 1 Tips This mode is for playback with higher sound quality than in Direct playback mode. This mode turns off the main unit display and analog video circuit. Doing so suppresses noise sources that affect sound quality. Press PURE to select “Direct”. Direct playback begins. 1 0 While DSD signals are played back, “DSD Direct” is displayed.
Contents Connections Playback Settings Tips Auto surround playback This mode detects the type of input digital signal, and automatically selects the corresponding mode for playback. Perform stereo playback when the input signal is PCM. When the input signal is Dolby Digital or DTS, the music is played back according to the respective channel number. 1 Press PURE to select “Auto”. Auto surround playback begins. 0 This can also be set by pressing PURE DIRECT on the main unit.
Contents Connections Playback Settings Tips Appendix Description of sound mode types Dolby sound mode Sound mode type Description Dolby Atmos Please select this mode to play content encoded with Dolby Atmos. If you have selected a different sound mode previously, please select again this mode for Dolby Atmos content play back.
Contents Connections Playback Settings Tips Appendix DTS sound mode Sound mode type Description DTS Surround This mode can be selected when playing sources recorded in DTS. DTS ES Dscrt6.1z1 This mode is suitable for playing discs recorded in DTS-ES. The surround back channel added using the discrete method is played as an independent channel. Since all channels are independent, the 360-degree spacial expressiveness and sound localization are enhanced. DTS ES Mtrx6.
Contents Connections Playback Settings Sound mode type Tips Appendix Description IMAX DTS This mode is automatically activated when playing back IMAX Enhanced content featuring a DTS bitstream. (v p. 183) 0 Also this mode is selectable when “Surround Parameter” - “IMAX” is set to “On” in the menu and a 48 kHz sampling frequency DTS 5.1 channel signal is being input. 0 When “Speaker Config.” - “Surr. Back” is set to “2 spkrs”, “Speaker Config.
Contents Connections Playback Settings Tips Appendix Auro-3D sound mode Sound mode type Description Auro-3D This mode uses an Auro-3D decoder to create three-dimensional audio output using the Height Channel. It is ideal for playback of signals encoded as Auro-3D with a Height Channel. If signals not encoded as Auro-3D are input, an Upmixer called the Auro-Matic is used to create highly realistic three-dimensional audio output.
Contents Connections Playback Settings Tips Appendix Auto sound mode Sound mode type Auto Description In this mode, the type of digital signal input, such as Dolby Digital, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Atmos, DTS, DTS-HD, DTS:X, DTS-ES, PCM (multi-channel) is detected, and the playback mode switches automatically to the corresponding mode. If the input signal is analog or PCM (2-channel), stereo playback is used.
Contents Connections Playback Settings Tips Appendix Sound mode that can be selected for each input signal 0 The following sound modes can be selected using the MOVIE, MUSIC and GAME buttons. . 0 Adjust the sound field effect with the menu “Surround Parameter” to enjoy surround sound the way you like it. (v p.
Connections Playback Settings Tips Appendix .
Connections Playback Settings Tips Appendix . Contents Input signal Multi-channel z8 DTS DTS-HD / DTS Express z3 z7 z8 z11 MOVIE button MUSIC button DTS Surround z7 Sound mode S S GAME button S DTS ES Dscrt 6.1 z7 S S S DTS ES Mtrx 6.
Connections Playback Settings Tips Appendix . Contents Input signal DTS:X IMAX DTS IMAX DTS:X PCM multi-channel Multi-channel z8 z3 z5 z6 z7 z8 z12 MOVIE button MUSIC button DTS:X z7 Sound mode S S GAME button S DTS:X MSTR z7 S S S DTS:X + Virtual:X z3 S S S IMAX DTS z7 z12 S S S IMAX DTS + Neural:X z7z12 S S S IMAX DTS + Virtual:X z3z12 S S S IMAX DTS:X z7z12 S S S IMAX DTS:X + Virtual:X z3z12 S S S Multi Ch In z7 S S S Multi Ch In 7.
Contents Connections Playback Settings Tips . o Views on the display q w A Shows a decoder to be used. 0 In the case of the Dolby Digital Plus decoder, “ ” is displayed. B Shows a decoder that creates sound output. ” indicates that the Dolby Surround decoder is being used.
Contents Connections Playback Settings Tips Appendix HDMI Control function A recent addition to the HDMI standard is CEC (Consumer Electronics Control), which allows control signals from one device to communicate with another device via the HDMI cable connection. Setting procedure 1 2 3 5 Enable the HDMI Control function of this unit. Set “HDMI Control” to “On”. (v p. 198) Turn the power on for all the devices connected by HDMI cable.
Contents Connections Playback Settings Tips Appendix Smart Menu function This function can be used to configure the settings of this unit, select an input source and set Tuner and Internet Radio stations using the TV remote control. 2 3 Enjoy content from the input source currently selected on this unit. o Source Enable the HDMI Control function of this unit and the TV. (v p. 198) Switch the input of this unit.
Contents Connections Playback Settings Tips o Setup Menu Displays a setup menu for configuring the settings of this unit. o Smart Select Calls up the “Smart Select” items registered to this unit. NOTE 0 If the “HDMI Control” or “Smart Menu” settings have been changed, always reset the power to connected devices after the change. 0 The Smart Menu function may not work properly depending on the specifications of your TV. In this case, set “Smart Menu” to “Off”. (v p.
Contents Connections Playback Settings Tips Appendix Sleep timer function You can have the power automatically switched to standby once a set time has elapsed. This is convenient for viewing and listening while going to sleep. The sleep timer function can be set for each zone. Z3 Z2 MAIN .
Contents Connections Playback Settings Press SLEEP when the sleep timer is in operation. The remaining time appears on the display. Press MAIN, Z2 or Z3 to select the operating zone with the remote control. o To cancel the sleep timer The button for the selected zone is lit. 2 Appendix o Checking the remaining time Using the sleep timer 1 Tips Press SLEEP to select “Off”. The sleep timer indicator on the display turns off. Press SLEEP and display the time you want to set.
Contents Connections Playback Settings Tips Appendix Smart select function Z3 Z2 Settings such as the input source, volume level and sound mode can be registered to the SMART SELECT 1 - 4 buttons. You can simply press one of the registered SMART SELECT buttons in subsequent playbacks to switch to the group of saved settings in a batch. By saving frequently used settings at the SMART SELECT 1 – 4 buttons, you will always be able to easily call up the same playback environment.
Contents Connections Playback Settings Tips Calling up the settings 1 2 Press MAIN, Z2 or Z3 to select the operating zone with the remote control. The button for the selected zone is lit. Press SMART SELECT. The Smart Select settings registered to the button you pressed are called up. 0 The default settings for the input source are as shown below.
Contents Connections Playback Settings 2 Changing the settings 1 Tips Press MAIN, Z2 or Z3 to select the operating zone with the remote control. The button for the selected zone is lit. Set the items below to the settings you want to register. 3 The following settings from A to K can be memorized for MAIN ZONE, and settings A and B can be memorized for ZONE2 and ZONE3. Press and hold the desired SMART SELECT until “Smartz Memory”, “Z2 Smartz Memory” or “Z3 Smartz Memory” appears on the display.
Contents Connections Playback Settings Tips Appendix Panel lock function To prevent accidental operation of this unit, you can disable operation of the buttons on the front panel. X Disabling all key button operations 1 ui ENTER 2 3 . 2 3 Display Use ui to select “FP/VOL LOCK On”. Press ENTER to enter the setting. All button operations except X are disabled.
Contents Connections Playback Settings Tips Canceling the Panel lock function 1 2 3 Press X while you press and hold BACK and ENTER with the unit in standby mode. Use ui to select “FP LOCK zOff”. (z The currently set mode.) Press ENTER to enter the setting. The Panel lock function is canceled. 0 Even when the Panel lock function is set, you can operate the unit using the remote control unit.
Contents Connections Playback Settings Tips Appendix Remote lock function When connecting an IR receiver, enable the Remote lock function. When the function is enabled, you can not perform operations with the remote control unit. By default, this function is disabled. X Disabling the sensor function of the remote control unit 1 ui ENTER 2 3 Press X while you press and hold BACK and ENTER with the unit in standby mode. Use ui to select “RC LOCK On”. Press ENTER to enter the setting.
Contents Connections Playback Settings Tips Appendix Switches light illumination on/off You can switch the light illumination around the main display on or off. The default setting is “On”. Light illumination 1 Press and hold DIMMER on the main unit for 3 seconds. 0 Carry out the same procedure if you want to change the settings again. .
Contents Connections Playback Settings Tips Appendix Web control function You can control this unit from a web control screen on a web browser. PC Router Controlling the unit from a web control 1 This unit 2 Switch the “Network Control” setting to “Always On”. (v p. 251) Check the IP address of this unit with “Information”. (v p. 246) Network/Information Friendly Name DHCP Connection IP Address MAC Address (Ethernet) MAC Address (Wi-Fi) Tablet Marantz AV7706 On Wired (Ethernet) 192.168.100.
Contents 4 Connections Playback Settings Tips Enter the IP address of this unit in browser’s address box. For example, if the IP address of this unit is “192.168.100.19”, enter “http://192.168.100.19”. http://192.168.100.19 Edit View Favorites Tools Help . File 5 When the top menu is displayed on the web browser, click on the menu item you want to operate.
Contents Connections Playback Settings Tips Appendix Playback in ZONE2/ZONE3 (Another room) You can operate this unit to enjoy video and audio in a room (ZONE2 and ZONE3) that is different from the room where this unit is placed (MAIN ZONE). You can simultaneously play back the same source in both the MAIN ZONE, ZONE2 and ZONE3. You can also play back separate sources in the MAIN ZONE, ZONE2 and ZONE3.
Contents Connections Playback Settings Tips Appendix o Connection 2 : Connection through the video output connector and external power amplifiers The audio signals of this unit’s ZONE2 and ZONE3 audio output connectors are played on the ZONE2 and ZONE3 power amplifiers. ZONE2 MAIN ZONE ZONE3 VIDEO VIDEO IN This unit COMPONENT VIDEO IN Y PB PR Power amplifier AUX IN or Power amplifier L R AUX IN .
Contents Connections Playback Settings Tips Appendix 0 If the input for ZONE2 and ZONE3 is set to “Source”, all types of input signals can be listened to from ZONE2 and ZONE3. 0 If the input for ZONE2 is set to a specific source (like CBL/SAT), only analog signal or 2-channel PCM signal input (from HDMI connectors or digital connectors (OPTICAL/ COAXIAL)) can be listened to from ZONE2. To playback HDMI signal other than 2-channel PCM in ZONE2, set “HDMI Audio” to “PCM”. (v p.
Contents Connections Playback Settings 1 Playback in ZONE2/ZONE3 Tips Appendix Press Z2 or Z3 to select the operating zone with the remote control. The button for the selected zone is lit. Z3 Z2 2 POWER X 3 Input source select buttons Press the input source select button to select the input source to be played. The audio signal of the selected source is output to ZONE2 or ZONE3.
Contents Connections Playback Settings Tips o Adjusting the volume (ZONE2/ZONE3) Use VOLUME df to adjust the volume. 0 At time of purchase, “Volume Limit” is set to “70 (–10 dB)”. (v p. 257) 0 Turn VOLUME after pressing ZONE SELECT on the main unit to adjust the volume. o Turning off the sound temporarily (Muting) (ZONE2/ZONE3) Press MUTE :. The sound is reduced to the level set at “Mute Level” in the menu. (v p. 257) 0 To cancel mute, either adjust the sound volume or press MUTE : again.
Contents Connections Playback Settings Tips Appendix Menu map When using menu operations, connect this unit to a TV and operate this unit while viewing the TV. The recommended settings are configured for this unit by default. You can customize this unit based on your existing system and your preferences. . Setting items . Audio Video Front panel Detailed items Description Page Center Level Adjust Adjusts the center channel volume to clarify the dialog for all sources.
Contents . Setting items Playback Settings Detailed items Tips Appendix Description Page Input Assign Changes input connector assignment and the audio input mode. 210 Source Rename Changes the display name for input source. 213 Hide Sources Removes from the display input sources that are not used. 213 Source Level Adjusts the playback level of the audio input.
Contents Setting items Connections Playback Settings Detailed items Tips Appendix Description Page . 【When the user is signed out the HEOS Account】 HEOS Account I have a HEOS Account Selects to sign in. 253 Create Account Creates new HEOS Account. 253 Forgot Password If you forgot your password, we'll send you an email with instructions about how to reset it. 253 【When the user is signed in the HEOS Account】 Front panel Signed in As Displays your HEOS Account.
Contents Connections . Setting items General Playback Settings Detailed items Tips Description Page Language Changes the language of the display on the TV screen. 254 Bluetooth Transmitter Sets Bluetooth transmitter settings. 254 ZONE2 Setup/ ZONE3 Setup Makes settings for audio playback with ZONE2 and ZONE3. 255 Zone Rename Changes the display title of each zone to one you prefer. 258 Smart Select Names Changes the Smart Select Name display title to one you prefer.
Contents Connections Playback Settings Tips Appendix Menu operations 1 MAIN The MAIN button lights. 2 3 4 5 uio p ENTER SETUP BACK Press MAIN on the remote control unit to set the operating zone to the MAIN ZONE. Press SETUP. The menu is displayed on the TV screen. Use ui p to select the menu to be set or operated, then press ENTER. Use o p to change to desired setting. Press ENTER to enter the setting. 0 To return to the previous item, press BACK.
Contents Connections Playback Settings Tips Appendix Audio Make audio-related settings. Center Level Adjust Subwoofer Level Adjust Adjusts the center channel volume to clarify the dialog for all sources. Adjusts the subwoofer channel volume for all input sources. o Center o Subwoofer 1 / Subwoofer 2 Adjusts the volume output from the center channel. Adjusts the volume level for the Subwoofer 1 and Subwoofer 2. –12.0 dB – +12.0 dB (Default: 0.0 dB) –12.0 dB – +12.0 dB (Default: 0.
Contents Connections Playback Settings Bass Sync Tips Appendix Surround Parameter For contents recorded in multi-channel such as Blu-ray discs, the recorded low frequency effects (LFE) may be out of synch and delayed. This function corrects such a delay of low frequency effects (LFE). You can adjust the surround audio sound field effects to match your preferences. The items (parameters) that can be adjusted depend on the signal being input and the currently set sound mode.
Contents Connections Playback Settings Compress dynamic range (difference between loud and soft sounds). This sets whether to output as specified in “Dynamic Compression” or output directly without compressing the dynamic range of audio recorded in the disc. On (Default): Outputs are given based on enabling the settings made in “Dynamic Compression” and Dialogue normalization function.
Contents Connections Playback Settings Tips Appendix o Speaker Virtualizer o Dialog Control Adjust the volume of dialog in movies, vocals in music, etc. so these can be heard more easily. The Speaker Virtualizer enhances the surround and height speaker channels to create an enveloping virtual surround effect. 0 – 6 (Default : 0) On (Default): Enables “Speaker Virtualizer”. Off: Disables “Speaker Virtualizer”.
Contents Connections Playback Settings Tips Appendix o IMAX Audio Settings o IMAX You can configure special IMAX audio settings to recreate the conditions of an IMAX theater. Sets the audio mode for IMAX playback. Auto (Default): Automatically enables the IMAX mode when IMAX content is detected. On: Enables IMAX settings for IMAX streaming content when automatic detection is not possible. Off: Disables the IMAX mode.
Contents Connections Playback Settings o Low Pass Filter Tips Appendix o Auro-Matic 3D Preset Set the low pass filter cutoff frequency of the LFE signal during IMAX playback. Selects the Auro-Matic 3D Preset for fine tuning the Auro-3D experience to specific audio material. 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 120 Hz) Small: “Small” is ideal for pop and chamber music.
Contents Connections Playback Settings Tips Appendix o Speaker Select o Auro-Matic 3D Strength Makes settings for the speakers outputting sound. Changes the level of the up-mixed channels in relation to the original input signal. The value ranges from 1 (no up-mixing) to 16 (Maximum level, providing maximum effect). Floor: Plays back without height speakers. Floor & Height (Default): Plays back with height speakers.
Contents Connections Playback Settings Tips Appendix M-DAX 0 The M-DAX indicator lights. 0 This item can be set with analog signals or PCM signal (Sample Rate = 44.1/48 kHz) is input. 0 This item default setting for “HEOS Music” is “Low”. All others are set to “Off”. 0 This cannot be set when the sound mode is set to “Direct” or “Pure Direct”. 0 This cannot be set when the input mode is set to “7.1CH IN”. 0 “M-DAX” settings are stored for each input source.
Contents Connections Playback Settings Tips Appendix o Adjust Audio Delay The timing mismatch between the picture and sound needs to be corrected manually. Compensates for incorrect timing between video and audio. 0 ms – 500 ms (Default : 0 ms) 0 Audio Delay for game mode can be set when “Video Mode” is set to “Auto” or “Game”. (v p. 202) 0 “Audio Delay” settings are stored for each input source. 0 This cannot be set when the input mode is set to “7.1CH IN”.
Contents Connections Playback Settings Tips Appendix o Power On Level Volume Define the volume setting that is active when the power is turned on. Set the MAIN ZONE (room where the unit is located) volume setting. Last (Default): Use the memorized setting from the last session. Set how volume is displayed. Mute: 0 - 98 (Default): Always use the muting on condition when power is turned on. Display in the range 0 (Min) to 98. 1 – 98 (–79 dB – 18 dB) : The volume is adjusted to the set level.
Contents Connections Playback Settings Tips Appendix o MultEQ® XT32 Audyssey® MultEQ® XT32 compensates for both time and frequency characteristics of the listening area based on Audyssey® Setup measurement results. Selection is done from three types of compensation curves. We recommend the “Reference” setting. Set Audyssey MultEQ® XT32, Audyssey Dynamic EQ®, Audyssey Dynamic Volume® and Audyssey LFC™. These can be selected after Audyssey® Setup has been performed.
Contents Connections Playback Settings o Dynamic EQ Tips Appendix o Reference Level Offset Solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Works with MultEQ® XT32. On (Default): Use “Dynamic EQ”. Off: Do not use “Dynamic EQ”. Audyssey Dynamic EQ® is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB.
Contents Connections Playback Settings o Dynamic Volume Tips Appendix o Audyssey LFC™ Solves the problem of large variations in volume level between TV, movies and other content (between quiet passages and loud passages, etc.) by automatically adjusting to the user’s preferred volume setting. Works with MultEQ® XT32. Heavy: Most adjustment to softest and loudest sounds. Medium: Medium adjustment to loudest and softest sound. Light: Least adjustment to loudest and softest sounds.
Contents Connections Playback Settings Appendix o Speaker Selection Graphic EQ Select whether to adjust tones for individual speakers or for all speakers. Uses the graphic equalizer to adjust the tone of each speaker. 0 Speakers for which “Graphic EQ” can be set differ according to the sound mode. 0 This can be set when “MultEQ® XT32” setting is “Off”. (v p. 189) 0 This cannot be set when the sound mode is set to “Direct” or “Pure Direct”.
Contents Connections Playback Settings Tips o Curve Copy Copy the Flat correction curve created in Audyssey® Setup. 0 “Curve Copy” is displayed after Audyssey® Setup has been performed. 0 “Curve Copy” cannot be used when using headphones. o Set Defaults The “Graphic EQ” settings are returned to the default settings.
Contents Connections Playback Settings Tips Appendix Video Make video-related settings. o Picture Mode Picture Adjust Select the desired picture mode according to the video content and your viewing environment. Picture quality can be adjusted. 0 This can be set when the “Video Conversion” setting is “On”. (v p. 202) 0 This can be set when “HDMI”, “COMP” or “VIDEO” is assigned for each input source. (v p.
Contents Connections Playback Settings Tips o Contrast Adjust picture contrast. 0 The two special adjustment modes, “ISF Day” and “ISF Night”, should be used by a certified technician to adjust the color calibration to match the installation conditions. We recommend that the settings and adjustments be carried out by an ISFcertified technician. 0 These settings can also be configured using “Picture Mode” in the option menu. (v p. 194) -50 – +50 (Default : 0) o Brightness Adjust picture brightness.
Contents Connections Playback Settings Tips o HDMI Pass Through HDMI Setup Selects how this unit will transmit HDMI signals to the HDMI output in standby power mode. Make settings for HDMI Audio Out, HDMI Pass Through and HDMI Control settings. NOTE 0 When “HDMI Pass Through” and “HDMI Control” is set to “On”, it consumes more standby power. (“HDMI Pass Through” (v p. 196), “HDMI Control” (v p.
Contents Connections Playback Settings o Pass Through Source Last: The most recently used input source will go into standby mode. CBL/SAT / DVD / Blu-ray / Media Player / Game / AUX / 8K / TV Audio / CDz (Default : CBL/SAT): Pass through the selected input source. Set whether to allow this unit to be turned on by the input source select button on the remote control when this unit is on standby. Power On + Source (Default): The power of this unit is turned on and the input source changes.
Contents Connections Playback Settings o HDMI Control Tips Appendix o ARC You can link operations with devices connected to HDMI and compatible with HDMI Control. On the TV connected to the HDMI MONITOR 1 connector, set whether to receive sound from the TV via HDMI. On: Use HDMI Control function. On: Use ARC function. Do not use HDMI Control function. Off (Default): Do not use ARC function.
Contents Connections Playback Settings o TV Audio Switching Tips Appendix o Power Off Control Sets automatic switching to the “TV Audio” input when a TV connected via HDMI sends an appropriate CEC control command to this unit. On (Default): Select the “TV Audio” input automatically when receiving a command from the TV. Off: Do not select the “TV Audio” input automatically when receiving a command from the TV. Links the power standby of this unit to external devices.
Contents Connections Playback Settings o Power Saving Tips Appendix o Smart Menu If “TV Speaker” is set as the audio output setting of your TV, this unit is automatically set to standby mode to reduce power consumption. This function is activated in the following cases. 0 When “TV Audio” is selected as the input source of this unit 0 When playing content from a device connected by HDMI On: Use Power Saving function. Off (Default): Do not use Power Saving function.
Contents Connections Playback Settings Appendix o HDMI Video Output Output Settings Select the HDMI monitor connector to be used. Makes settings for video output. 0 This can be set when “HDMI”, “COMP” or “VIDEO” is assigned for each input source. (v p. 211) 0 “Resolution”, “Sharpness”, “Progressive Mode” and “Aspect Ratio” can be set when “i/p Scaler” is set to anything other than “Off”. (“Resolution” (v p. 203), “Sharpness” (v p. 203), “Progressive Mode” (v p. 204), “Aspect Ratio” (v p.
Contents Connections Playback Settings o Video Mode Tips Appendix o Video Conversion Configure the video processing method to match the type of video content. The input video signal is converted automatically in conjunction with the connected TV. (v p. 308) Auto (Default): Process video automatically based on the HDMI content information. On (Default): The input video signal is converted. Off: The input video signal is not converted. Game: Always process video for game content.
Contents Connections Playback Settings o Resolution Appendix o Sharpness Set the output resolution. You can set “Resolution” separately for HDMI output of the analog video input and HDMI input. Auto (Default): The resolution supported by the TV connected to the HDMI MONITOR OUT connector is detected automatically and the appropriate output resolution is set. 480p/576p / 1080i / 720p / 1080p / 4K / 8K : Set the output resolution.
Contents Connections Playback Settings o Progressive Mode Tips Appendix o Aspect Ratio Set an appropriate progressive conversion mode for the source video signal. Auto (Default): The video signal is automatically detected and the appropriate mode is set. Video: Select mode suitable for video playback. Video and Film: Select mode suitable for video and 30frame film material playback. Set the aspect ratio for the video signals output to the HDMI. 16:9 (Default): Output at 16:9 aspect ratio.
Contents Connections Playback Settings Component Video Out Tips Appendix On Screen Display Set the zone to which the component video output connector is assigned. Select the on-screen display user interface preferences. MAIN ZONE (Default): Assigns the component video output connector to MAIN ZONE. o Volume ZONE2: Assigns the component video output connector to ZONE2. Sets where to display the volume level. Bottom (Default): Top: Off: Display at the bottom. Display at the top.
Contents Connections Playback Settings o Now Playing Show display continuously. Auto Off: Show display for 30 seconds after operation. Appendix Screen Saver Sets the display time for the playback display when the input source is “HEOS Music” or “Tuner”. Always On (Default): Tips Select the screen saver setting. A screen saver is activated if no operation is performed for more than 5 minutes when no video signal is input or when the same screen (e.g. the setup menu) is displayed.
Contents Connections Playback Settings Set the format of 4K and 8K signal to be played back by this unit when the TV or playback device connected to this unit is HDMI 4K or 8K signal compatible. Support Resolution o 4K/8K Signal Format 4K 24p, 4K 30p, 4K 25p Set the format of 4K and 8K signal played back by this unit. Standard: Select if your TV and playback devices support 4K 60p 4:2:0 8 bit video signals.
Contents Connections Playback Settings Tips Appendix HDCP Setup 0 When setting this to “Enhanced”, we recommend using a “Premium High Speed HDMI Cable” or “Premium High Speed HDMI Cable with Ethernet” that has an “HDMI Premium Certified Cable” label attached to the product package. 0 When setting this to “8K Enhanced”, we recommend using an “Ultra High Speed 48 Gbps HDMI cable”.
Contents Connections Playback Settings Tips TV Format Set the video signal format to be output for the TV you are using. o Format NTSC (Default): Select NTSC output. PAL: Select PAL output. 0 “Format” can also be set by the following procedure. However, the menu screen is not displayed. Following the display content to make the setting. 1. Press and hold the main unit’s STATUS and ZONE SELECT at the same time for at least 3 seconds. “zVideo Format ” appears on the display. 2.
Contents Connections Playback Settings Tips Appendix Inputs Perform settings related to input source playback. You do not have to change the settings to use the unit. Make settings when needed. Input Assign 0 By default, each item is set as follows. By making connections as indicated by the input sources printed on the audio/video input connectors of this unit, you can just press one of the input source select buttons to easily play back audio or video from a connected device.
Contents Connections Playback Settings n TV set top box/satellite users please note Set this to change the digital audio input connectors assigned to the input sources. 0 The same input connector can be assigned to multiple input sources. For example, assign the same HDMI input connector to multiple sources to use each input source in combination with analog or digital audio as you prefer. In such cases, set the audio connector for playback in “INPUT MODE”.
Contents Connections Playback Settings o INPUT MODE Tips o Set Defaults Set the audio input modes for each input source. It is normally recommended to set the audio input mode to “AUTO”. AUTO (Default): Automatically detect input signal and perform playback. HDMI: Play only signals from HDMI input. DIGITAL: Play only signals from digital audio input. ANALOG: Play only signals from analog audio input. 7.1CH IN: Only signals input from the 7.1CH IN connector will be played back.
Contents Connections Playback Settings Source Rename Tips Hide Sources 0 Changes the display name of the input source. Remove from the display input sources that are not used. Once changed, the name is displayed on the display and menu screens of this unit. 0 If the device name can be acquired from a connected HDMI device, the display name is changed automatically. Use this function to change names as needed when the device you are using differs from the input source on this unit.
Contents Connections Playback Settings Tips Source Level This function corrects the playback level of the selected input source’s audio input. Make this setting if there are differences in the input volume levels between the different sources.
Contents Connections Playback Settings Tips Appendix Speakers The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically. This is called “Audyssey® Setup”. You do not have to perform Audyssey® Setup when you have already performed “Speaker Calibration” in “Setup Assistant”. To set up the speakers manually, use “Manual Setup” on the menu. (v p.
Contents Connections Playback Settings o About the main listening position 0 Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows and turn off the power on electronic devices (radios, air conditioners, fluorescent lights, etc.). The measurements could be affected by the sounds emitted by such devices. 0 During the measurement process, place cell phones outside the listening room. Cell phone signals could disrupt the measurements.
Contents Connections Playback Settings 1 Procedure for speaker settings (Audyssey® Setup) Tips Appendix Attach the Sound calibration microphone to the supplied microphone stand or own tripod and install it at the main listening position. When installing the Sound calibration microphone, point the tip of the microphone toward the ceiling and adjust the height to match the height of the ears of a listener in a seated position.
Contents Playback Settings 4 Connect the Sound calibration microphone to the SETUP MIC jack of this unit. When the Sound calibration microphone is connected, the following screen is displayed. . Audyssey Setup Your AV preamp can automatically measure the acoustics of your room then optimize your speakers using the included microphone and microphone stand. Set the following items if necessary. 5 Amp Assign Channel Select Dolby Speaker Setup Tips Select “Start”, then press ENTER.
Contents Playback Settings 7 When the following screen is displayed, select “Begin Test” and then press ENTER. Start the measurement of the first position. Tips Appendix When the detected speaker is displayed, select “Next” and then press ENTER. Audyssey Setup Speaker Detection Audyssey Setup Select “Begin Test” to start the calibration. NOTE: You will hear a series of loud chirps starting and stopping during the tests. Front Center Subwoofer Surround Surr.
Contents Playback Settings 9 Move the Sound calibration microphone to position 2, select “Continue”, then press ENTER. The measurement of the second position starts. Measurements can be made in up to eight positions. Tips Appendix Repeat step 8, measuring positions 3 to 8. 0 To skip measuring the fourth and subsequent listening position, press o to select “Complete” and press ENTER to proceed to step 11.
Contents 11 Connections Playback Settings 12 Perform the settings for Audyssey Dynamic EQ® and Audyssey Dynamic Volume®. The following screen is displayed during the analysis. Configure the settings as preferred. Tips Appendix When the analysis and storage ends, unplug the Sound calibration microphone from the SETUP MIC jack on the main unit and then press “Next”. Audyssey Setup Now Analyzing and correcting your room data. Please disconnect the microphone from your AV preamp.
Contents Connections Playback Settings 13 0 When performing Audyssey® Setup for the first time, the measurement data is automatically saved to “Preset 1” of “Speaker Preset”. 0 If Audyssey® Setup has already been performed, the following “Speaker Preset” selection screen is displayed. Tips Select “Details” and press ENTER to verify the measurement results. 0 Subwoofers may measure a greater reported distance than the actual distance due to added electrical delay common in subwoofers.
Contents Connections Playback Settings Tips Appendix Error messages An error message is displayed if Audyssey® Setup could not be completed due to speaker placement, the measurement environment, etc. If an error message is displayed, check the relevant items and perform the necessary measures. Be sure to turn off the power before checking speaker connections. Examples Error details No speakers found.
Contents Connections Playback Settings o Subwoofer level error message and how to adjust 1 2 The optimal level of each subwoofer channel for Audyssey® Setup measurement is 75 dB. During subwoofer level measurement, an error message is displayed when one level of subwoofers is outside the 72 – 78 dB range. When using a subwoofer with built-in amplifier (active type), adjust the subwoofer volume so that the subwoofer level is within the 72 to 78 dB range.
Contents Connections Playback Settings Tips Retrieving Audyssey® Setup settings If you set “Restore...” to “Restore”, you can return to Audyssey® Setup measurement result (value calculated at the start by MultEQ® XT32) even when you have changed each setting manually. Audyssey Setup Your AV preamp can automatically measure the acoustics of your room then optimize your speakers using the included microphone and microphone stand. Set the following items if necessary.
Contents Connections Playback Settings Manual Setup Tips Appendix Amp Assign You can change the Pre Amplifier assignment according to your speaker system. Perform when setting the speakers manually or when changing settings made in Audyssey® Setup. 0 If you enable new speakers in the speaker configuration menu after performing Audyssey® Setup, you will no longer be able to select Audyssey MultEQ® XT32, Audyssey Dynamic EQ® or Audyssey Dynamic Volume®. (v p.
Contents Connections Playback Settings Select the floor speakers location. When “Assign Mode” is set to “9.1ch (Bi-Amp)” or “9.1ch + Front B” in the menu, select the PRE OUT connectors used for bi-amp or second pair front speakers. The assigned channels are output from the HEIGHT2 PRE OUT connectors. Up to one pair of height, ceiling, and Dolby Atmos Enabled channels can be used. SURROUND BACK: The assigned channels are output from the SURROUND BACK PRE OUT connectors.
Contents Connections Playback Settings Tips o Height n Height Sp Select the number of the height speakers and ceiling speakers used in MAIN ZONE. None: Uses no height and ceiling speakers. 2ch: Uses a set of (two) height speakers or ceiling speakers. 4ch (Default): Uses two sets of (four) height speakers or ceiling speakers. 5ch: Uses five height speakers z z If “5ch” is selected, connect the Top Surround speaker to the SUBWOOFER 2 connector.
Contents Connections Playback Settings Tips Appendix n Layout Select the height, ceiling, or Dolby Atmos Enabled speaker location. The layouts that can be selected differ depending on the combinations of “Assign Mode” and “Floor” in the menu. (“Assign Mode” (v p. 226), “Floor” (v p.
Contents Connections Playback Settings NOTE Height Sp Dolby Sp 2ch 2ch z1 None 4ch z1 Settings Layout Front Dolby & Top Rear Front Dolby & Rear Height Front Height & Surr. Dolby Front Height & Back Dolbyz4 Top Front & Surr. Dolby Top Front & Back Dolbyz4 Front Dolby & Surr.
Contents Connections Height Sp Dolby Sp 5ch None Playback Settings NOTE z5 Settings Layout Front Height & Surr. Height Front Height & Rear Heightz2 Tips HEIGHT1 Front Height Front Height Appendix AUDIO OUT connectors HEIGHT2 SUBWOOFER2 Surr. Height Top Surround Rear Height Top Surround z2 For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.
Contents Connections Playback Settings o View Terminal Config. Tips Appendix Speaker Config. This shows how to connect the PRE OUT connectors for your “Amp Assign” setting on the menu screen. Select whether or not speakers are present, playback capacity for low bass frequencies and speaker size. 0 When speakers for which you assigned Height1 in “Amp Assign” are set to “None”, “None” is automatically set for Height2. o Front Set the front speaker size.
Contents Connections Playback Settings Tips Appendix o Surround o Center Set the presence and size of the surround speakers. Set the presence and size of the center speaker. Large: Use a large speaker that can adequately play back very low bass frequencies. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default): Use a small speaker that has inadequate playback capacity for very low bass frequencies.
Contents Connections Playback Settings o Surr. Back Tips Appendix o Front Height Set the presence, size and number of surround back speakers. Set the presence and size of the front height speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default): Use a small speaker that has inadequate playback capacity for very low bass frequencies.
Contents Connections Playback Settings Tips Appendix o Surround Dolby o Top Front Set the presence and size of the surround Dolby speakers. Set the presence and size of the top front speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default): Use a small speaker that has inadequate playback capacity for very low bass frequencies.
Contents Connections Playback Settings Tips Appendix o Rear Height o Surr. Height Set the presence and size of the rear height speakers. Set the presence and size of the surround height speakers. Large: Use a large speaker that can adequately play back very low bass frequencies. Large: Use a large speaker that can adequately play back very low bass frequencies. Small (Default): Use a small speaker that has inadequate playback capacity for very low bass frequencies.
Contents Connections Playback Settings o Top Surround Use a large speaker that can adequately play back very low bass frequencies. Small (Default): Use a small speaker that has inadequate playback capacity for very low bass frequencies. None: Select when the top surround speaker is not connected. Set distance from listening position to speakers. Measure beforehand the distance from the listening position to each speaker. o Unit Set the unit of distance. Feet (Default) Meters o Step 0 When “Surr.
Contents Connections Playback Settings o Set the distance Tips Appendix o Dolby Speaker Setup Set the distance between the Dolby Atmos Enabled speaker and the ceiling. 0.0 ft – 60.0 ft / 0.00 m – 18.00 m 3.0 ft - 11.0 ft / 0.90 m - 3.30 m (Default: 6.0 ft / 1.80 m) 0 The speakers that can be selected differ depending on the “Amp Assign” and “Speaker Config.” settings. (“Amp Assign” (v p. 226), “Speaker Config.” (v p. 232)) 0 Default settings: Front L / Front R / F. Height L / F.
Contents Connections Playback Settings Tips Levels Set the volume of the test tone to be the same at the listening position when it is output from each speaker. o Test Tone Start A test tone is output from the selected speaker. While listening to the test tone, adjust the volume output from the selected speaker. –12.0 dB – +12.0 dB (Default : 0.0 dB) 0 The set “Levels” are reflected in all sound modes.
Contents Connections Playback Settings Tips Appendix o Set the crossover frequency Crossovers 40 Hz / 60 Hz / 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 80 Hz) Set in accordance with the lower limit frequency of the base frequencies that can be played back through each speaker. See the speaker manual for information concerning speaker crossover frequency.
Contents Connections Playback Settings Tips o LPF for LFE Bass Set LFE signal playback range. Set this when you want to change the playback frequency (low pass filter point) of the subwoofer. Set subwoofer and LFE signal range playback. o Subwoofer Mode 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 120 Hz) Select low range signals to be reproduced by subwoofer.
Contents Connections Playback Settings Front Speaker Tips Appendix 2ch Playback Set the front speaker A/B to use for every sound mode. A (Default): Front speaker A is used. B: Front speaker B is used. A+B : Both front speakers A and B are used. Select the method for setting the speakers used in the 2-channel direct and stereo playback modes. o Setting Select the method for setting the speakers used in the 2-channel direct and stereo playback modes.
Contents Connections Playback Settings o Subwoofer Tips Appendix o SW Mode Set the presence of a subwoofer. Select low range signals to be reproduced by subwoofer. Yes (Default): Use a subwoofer. No: Select when a subwoofer is not connected. 0 When “Speaker Config.” - “Subwoofer” in the menu is set to “None”, No is automatically set. (v p. 233) If the “Front” setting is “Small”, the setting is automatically “Yes”.
Contents Connections Playback Settings o Crossover Tips o Level FL / Level FR Set the maximum frequency of the bass signal output from each channel to the subwoofer. Adjust the level of each channel. -12.0 dB – +12.0 dB (Default: 0.0 dB) 40 Hz / 60 Hz / 80 Hz / 90 Hz / 100 Hz / 110 Hz / 120 Hz / 150 Hz / 180 Hz / 200 Hz / 250 Hz (Default: 80 Hz) 0 This can be set when “2ch Playback” - “Subwoofer” is set to “Yes”.
Contents Connections Playback Settings Tips Speaker Preset Two speaker settings can be saved to suit the environments where you use your speakers. For example, you can configure two presets easily to switch between equalizer or speaker settings measured using Audyssey® Setup if the characteristics of your room differ depending on factors such as whether you use the screen.
Contents Connections Playback Settings Tips Appendix Network To use this unit by connecting it to a home network (LAN), you must configure network settings. If you set up your home network (LAN) via DHCP, set “DHCP” to “On”. (Use the default setting.) This allows this unit to use your home network (LAN).
Contents Connections Playback Settings Appendix o Use iOS Device Wi-Fi Setup Use your iOS device (iPhone/iPod/iPad) to connect to the network. By connecting your iOS device to this unit using Wi-Fi, the unit can be automatically connected to the same network as your device. Connect to a wireless LAN (Wi-Fi) router. The router can be connected in the following ways. Select the connection method to suit your home environment. 1. Select “Use iOS Device” on the TV screen. 2.
Contents Connections Playback Settings o WPS Router Tips o Manual Use a WPS-compatible router to connect using the push button method. 1. Select “Push Button” on the TV screen. 2. Switch to the WPS mode by pressing the WPS button of the router you wish to connect to. 0 The time for pressing the button varies depending on the router. 3. Select “Connect” on the TV screen within 2 minutes. Enter the name (SSID) and password of the network you wish to connect to. 1. Set the following items.
Contents Connections Playback Settings Tips Appendix Settings 0 The wireless LAN (Wi-Fi) settings of this unit can also be configured from a PC or tablet that supports wireless LAN connection. Configure the IP address. 0 If you are using a broadband router (DHCP function), the information required for network connection such as the IP address will be automatically configured since the DHCP function is set to “On” in the default settings of this unit.
Contents Connections Playback Settings o DHCP Tips o Default Gateway Selects how to connect to the network. When connected to a gateway (router), input its IP address. On (Default): Configure the network settings automatically from your router. Off: Configure the network settings manually. o DNS Enter the DNS address indicated in the documentation supplied by your provider. o IP Address Set the IP address within the ranges shown below.
Contents Connections Playback Settings Network Control Tips Appendix Friendly Name Enables network communication in standby power mode. Off In Standby: Suspend network function during standby. Always On (Default): Network is on during standby. Main unit operable with a network compatible controller. The Friendly Name is the name of this unit displayed on the network. You can change the Friendly Name according to your preferences. o Friendly Name Selects Friendly Name from the list.
Contents Connections Playback Settings Checks whether this unit has access to the Internet (WAN). Used to check the network connection. OK o Physical Connection Error: Checks the physical LAN port connection. OK The LAN cable is not connected. Check the connection. Failed to connect to the Internet. Check the Internet connection environment or router settings. AirPlay Settings for Apple AirPlay. 0 When connected using a wireless LAN, “Connection be displayed.
Contents Connections Playback Settings Tips Appendix HEOS Account Make HEOS Account-related settings. HEOS Account is needed in order to use HEOS Favorites. The menu displayed differs depending on the status of the HEOS Account. You have not signed in You have already signed in o I have a HEOS Account o Signed in As If you already have a HEOS Account, enter the current account name and password to sign in. The currently signed in HEOS Account is displayed.
Contents Connections Playback Settings Tips Appendix General Make various other settings. Language Bluetooth Transmitter Sets this unit's Bluetooth transmitter. Set to use Bluetooth headphones to listen to audio playing in the MAIN ZONE. Set the language for display the menu on the TV screen. English / Français / Español (Default: English) o Transmitter 0 “Language” can also be set up by the following operation. However, the menu screen is not displayed.
Contents Connections Playback Settings Appendix ZONE2 Setup / ZONE3 Setup o Device List Available devices are displayed in the list once you start pairing mode on the Bluetooth headphones you want to connect. Select your Bluetooth headphones from the list to pair them. This unit can only pair with one Bluetooth headphone at a time. However, up to 8 Bluetooth headphones can be registered. Switch between registered devices from Device List in the “Bluetooth Transmitter” setup menu.
Contents Connections Playback Settings o Lch Level Tips Appendix o HDMI Audio (ZONE2 only) Adjust the left channel output level. Selects the audio signal format for playing an HDMI source in ZONE2. -12 dB – +12 dB (Default : 0 dB) Through (Default): The HDMI audio signal is passed through this unit to the device in ZONE2. PCM: The HDMI audio signal input into this unit is converted to a PCM signal that can be output from the ZONE2 PRE OUT connectors.
Contents Connections Playback Settings o Volume Limit Tips o Mute Level Make a setting for maximum volume. Set the amount of attenuation when muting is on. 60 – 80 (–20 dB – 0 dB) (Default : 70 (-10 dB)) Full (Default): Off: Do not set a maximum volume. The sound is muted entirely. -40 dB : The sound is attenuated by 40 dB down. -20 dB : The sound is attenuated by 20 dB down. 0 This can be set when “Volume Level” is set to “Variable”. (v p.
Contents Connections Playback Settings Zone Rename Select the conditions for activating trigger out. For details about how to connect the DC OUT jacks, see “DC OUT jacks” (v p. 88). MAIN ZONE / ZONE2 / ZONE3 The default setting is restored for the edited zone name. n When setting for zone (MAIN ZONE / ZONE2 / ZONE3) Trigger out is activated through linkage to the power of the zone set to “On”. 0 Up to 10 characters can be input.
Contents Connections Playback Settings Appendix o ZONE2 / ZONE3 Auto Standby When there are no operations for a certain period of time as set here, the power is automatically shut off even if there is audio or video input. Set so the unit power automatically switches to standby. o MAIN ZONE Sets the time for switching to auto standby when there are no audio or video signals input into this unit.
Contents Connections Playback Settings Tips Front Display Makes settings related to the display on this unit. o Dimmer Adjust the display brightness of this unit. Bright (Default): Normal display brightness. Dim: Reduced display brightness. Dark: Very low display brightness. Off: Turns the display off. 0 You can also adjust the display by pressing DIMMER on the main unit.
Contents Connections Playback Settings Appendix o Auto-Update Firmware Turns on Automatic Updates so that futures updates are automatically downloaded and installed when this unit is in standby mode. Checks for the latest firmware information about updates and upgrades, updates the firmware, and sets up the notification message display for upgrades. n Auto-Update o Check for Update This unit will automatically update to the newest firmware when in standby mode. Check for firmware updates.
Contents Connections Playback Settings o Allow Update Tips Appendix o Upgrade Notification Enable or disable updates and upgrades for this unit. On (Default): Enables this unit to receive updates and upgrades. Off: Prevents this unit from receiving update and upgrade. When the latest Upgrade firmware is available, a notification message is displayed on the TV screen at power on. The notification message is displayed for about 40 seconds when the power is turned on.
Contents Connections Playback Settings o Add New Feature Notes concerning use of “Update” and “Add New Feature” Upgrade Package: Display the items to be upgraded. Upgrade Status: Display a list of the additional functions provided by the upgrade. requirements and settings for an Internet connection. (v p. 85) 0 Do not turn off the power until updating or upgrading is completed. 0 Approximately 1 hour is required for the updating/upgrading procedure to be completed.
Contents Connections Playback Settings Tips Appendix o Video Information Show information about this unit settings, input signals, etc. Show the HDMI input/output signals and HDMI monitor information for MAIN ZONE. o Audio HDMI Signal Info. Resolution / HDR / Color Space / Pixel Depth / ALLM / QMS / QFT Show the audio information for MAIN ZONE. Sound Mode: The currently set sound mode. Input Signal: The input signal type.
Contents Connections Playback Settings o Firmware Tips Appendix o Notifications Version: Displays information for the current firmware. DTS Version: Displays the current DTS version. Displays and sets notifications. Also, sets whether or not to display the notification when the power is turned on. Notification Alerts On (Default): Notification messages are displayed. Off: Notification messages are not displayed.
Contents Connections Playback Settings Usage Data Tips Appendix Save & Load To help us improve our products and customer service, Marantz collects anonymous information about how you use this unit (such as frequently used input sources and sound modes and speaker settings). Marantz will never provide any information we collect to third parties. Yes: Provide information on the operating status of this unit. No: Do not provide information on the operating status of this unit.
Contents Connections Playback Settings Tips Appendix Reset Setup Lock Returns settings to the factory default. Initialization can be performed for all unit settings or for Network settings only. Protect settings from inadvertent changes. o Lock On: Turn protection on. Off (Default): Turn protection off. o All Settings All settings are reset to the factory default values. o Network Settings 0 When cancelling the setting, set “Lock” to “Off”.
Contents Connections Playback Settings Tips Appendix Operating external devices with the remote control unit When preset codes are registered in the included remote control unit, it can then be used to operate any devices you have, such as DVD players or TVs made by different manufacturers. Operation mode indicators Z3 Z2 MAIN DEVICE MENU Input source select buttons OPTION SETUP SMART SELECT 1–4 .
Contents Connections Playback Settings Tips n Registering DVD players Registering preset codes 1 There are two methods for registering preset codes; the simple method for registering preset codes of Marantz players, the method for registering the preset numbers of other manufacturers’ devices. 0 “Registering Marantz players” (v p. 269) 0 “Registering by entering preset numbers” (v p. 270) Press and hold down DVD and OPTION until the DEV.
Contents Connections Playback Settings n Registering multiple players at the same time 1 Blu-ray Disc DVD player CD player player P The following table shows the device groups that can be registered for each of the input source select buttons. Check the preset number of the device you want to register beforehand in the “Remote Control Preset Codes” file. http://manuals.marantz.com/AV7706/preset/ AV7706PresetCodes.
Contents 1 2 Connections Playback Settings Tips Press and hold down the input source button that you want to register the preset code to and SETUP until the DEV., TV and AVP indicators are flashing green. Enter the preset number (4 digits) listed for the device in the Preset Code Table using the number buttons (0 – 9) on the remote control. 0 Some manufacturers use more than one type of preset code. Preset codes to change the number and verify correct operation.
Contents Connections Playback Settings Operating devices Tips Appendix n TV group (TV) operation To operate an external device, press the input source button registered with the preset code, followed by one of the buttons in the following tables. Operation buttons 0 The “DEV.” indicator lights when an external device is being operated. 0 The “TV” indicator lights when the TV is being operated. 0 To operate the menu of this unit, press MAIN before operating the unit.
Contents Connections Playback Settings n DVD group (DVD player / DVD recorder) operation Operation buttons Tips Appendix n CD group (CD player / CD recorder) operation Function Operation buttons Function DEVICE X Power on/off DEVICE X Power on/off DEVICE MENU (Popup) Menu DEVICE MENU (Popup) Menu INFO Information INFO Information OPTION Top menu uiop Cursor operation uiop Cursor operation ENTER Enter ENTER Enter 2 Stop BACK Back 3 Pause SETUP Setup 1 Playback 2 St
Contents Connections Playback Settings Appendix n BD group (Blu-ray Disc player) operation n CBL/SAT group (Set top box for satellite (SAT)/cable TV (CBL)/ Media player/IP TV) operation Operation buttons Tips Operation buttons Function Function DEVICE X Power on/off DEVICE X Power on/off DEVICE MENU (Popup) Menu DEVICE MENU Menu INFO Information CH/PAGE df Switch channels (up/down) OPTION Top menu INFO Information uiop Cursor operation uiop Cursor operation ENTER Enter ENTER
Contents Connections Playback Settings Tips Initializing registered preset codes 1 Press and hold down MAIN and OPTION until the DEV., TV and AVP indicators on the remote are flashing green, then release.
Contents Connections Playback Settings Tips Appendix Setting the back light You can turn off the backlight of the remote control unit. 0 Backlight is set on in the factory settings. Disabling the backlight 1 Press and hold both SETUP and Light button until the DEV., TV and AVP indicators on the remote are flashing green, then release. 0 The backlight function can be turned on by performing step 1 again while the backlight function is off. Light button .
Contents Connections Playback Settings Tips Appendix Specifying the zone used with the remote control unit To prevent accidental misuse, you can set the zone for which the remote control unit is used. Z3 Z2 1 MAIN Press and hold down either MAIN, Z2 or Z3 and SETUP at the same time until the DEV., TV and AVP indicators flash green. MAIN: When only using MAIN ZONE Z2: When using MAIN ZONE and ZONE2 Z3 (Default): When using MAIN ZONE, ZONE2 and ZONE3 .
Contents Connections Playback Settings o Contents Appendix Troubleshooting Tips I want the volume not to become too loud by mistake 279 I want to keep the volume at the same level when I turn the power on 279 I want to have the subwoofer always output audio 279 I want to make human voices in the movies clearer 279 I want to keep bass and clarity during playback at a lower volume level I want to automatically adjust the volume level difference in content such as TV and movies Operations canno
Contents Connections Playback Settings Tips Appendix Tips I want the volume not to become too loud by mistake 0 Set the volume upper limit for “Volume Limit” in the menu beforehand. This prevents children or others from increasing the volume too much by mistake. You can set this for each zone. (“Volume” (v p. 188), “Volume Limit” (v p.
Contents Connections Playback Settings Tips Appendix I want to set the optimized listening environment after changing the configuration/position of the speakers or changing a speaker to a new one 0 Perform Audyssey® Setup. This automatically makes the optimized speaker settings for the new listening environment. (v p. 215) I want to combine a desired video with the current music 0 Set “Video Select” in the option menu to “On”.
Contents Connections Playback Settings Tips Appendix Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other devices operating properly? 0 If steps 1 to 3 above do not improve the problem, restarting the device may improve the problem. Continue pressing the X button on the unit until “Restart” appears in the display, or remove and re-insert the power cord of the unit.
Contents Connections Playback Settings Tips Appendix Power does not turn on / Power is turned off Power does not turn on. 0 Check whether the power plug is correctly inserted into the power outlet. (v p. 89) Power automatically turns off. 0 The sleep timer is set. Turn on the power again. (v p. 158) 0 “Auto Standby” is set. “Auto Standby” is triggered when there is no operation for a set amount of time. To disable “Auto Standby”, set “Auto Standby” on the menu to “Off”. (v p.
Contents Connections Playback Settings Tips Appendix Operations cannot be performed through the remote control unit Operations cannot be performed through the remote control unit. 0 Batteries are worn out. Replace with new batteries. (v p. 9) 0 Operate the remote control unit within a distance of about 23 ft/7 m from this unit and at an angle of within 30°. (v p. 9) 0 Remove any obstacle between this unit and the remote control unit.
Contents Connections Playback Settings Tips Appendix No sound comes out No sound comes out of speakers. 0 Check the connections for all devices. (v p. 44) 0 Insert connection cables all the way in. 0 Check that input connectors and output connectors are not reversely connected. 0 Check cables for damage. 0 Check the speaker connections and configurations. (v p. 49) 0 Check the connections for PRE OUT connectors. (v p. 44) 0 Check whether the audio device power is turned on. (v p.
Contents Connections Playback Settings Tips Appendix Desired sound does not come out The volume does not increase. 0 The maximum volume is set too low. Set the maximum volume using “Limit” on the menu. (v p. 188) 0 Appropriate volume correction processing is performed according to the input audio format and settings, so the volume may not reach the upper limit. The volume of Bluetooth headphones does not decrease. 0 Bluetooth headphones volume cannot be adjusted from this unit.
Contents Connections Playback Settings Tips Appendix No sound is produced from subwoofer. 0 Check the subwoofer connections. 0 Turn on the subwoofer’s power. 0 Set “Speaker Config.” - “Subwoofer” in the menu to “1 spkr” or “2 spkrs”. (v p. 233) 0 When “Speaker Config.” - “Front” in the menu is set to “Large”, depending on the input signal and the sound mode, no sound may be output from the subwoofer. (v p.
Contents Connections Playback Settings Tips Appendix Audyssey MultEQ® XT32, Audyssey Dynamic EQ®, Audyssey Dynamic Volume® and Audyssey LFC™ cannot be selected. 0 These cannot be selected when you have not performed Audyssey® Setup. (v p. 215) 0 Switch to a sound mode other than “Direct” or “Pure Direct”. (v p. 143) 0 Audyssey Dynamic EQ®, Audyssey Dynamic Volume® and Audyssey LFC™ cannot be selected when sound mode is “DTS Virtual:X” or sound mode that have “+ Virtual:X” in the sound mode name.
Contents Connections Playback Settings Tips Appendix Sound is interrupted or noise occurs During playback from the Internet radio or USB memory device, sound is occasionally interrupted. 0 When the transfer speed of the USB memory device is slow, sound may occasionally be interrupted. 0 The network communication speed is slow or the radio station is busy. When making a call on iPhone, noise occurs in audio output on this unit. 0 When making a call, keep a distance of 0.
Contents Connections Playback Settings Tips Appendix No video is shown on the TV No picture appears. 0 Check the connections for all devices. (v p. 72) 0 Insert connection cables all the way in. 0 Check that input connectors and output connectors are not reversely connected. 0 Check cables for damage. 0 Match the input settings to the input connector of the TV connected to this unit. (v p. 210) 0 Check that the proper input source is selected. (v p. 91) 0 Check the video input connector setting.
Contents Connections Playback Settings Tips Appendix No video from an input source such as a game console is shown on the TV. 0 When special video signals are input from a game console, etc., the Video Conversion function may not function. Connect the input connector to the monitor output connector of the same type. While the menu is being displayed, no video is shown on the TV.
Contents Connections Playback Settings Tips Appendix The menu screen is not displayed on the TV The menu screen or status information screen is not displayed on the TV. 0 The menu screen is only displayed on this unit and a TV connected with an HDMI cable. If this unit is connected to a TV using a different video output connector, operate while watching the display on this unit. 0 The status information will not appear on the TV when the following video signals are being played.
Contents Connections Playback Settings Tips Appendix AirPlay cannot be played back The AirPlay icon is not displayed on iTunes / iPhone / iPod touch / iPad. 0 This unit and PC / iPhone / iPod touch / iPad are not connected to the same network (LAN). Connect it to the same LAN as this unit. (v p. 85) 0 The firmware on iTunes / iPhone / iPod touch / iPad is not compatible with AirPlay. Update the firmware to the latest version. Audio is not output.
Contents Connections Playback Settings Tips Appendix USB memory devices cannot be played back USB memory device is not recognized. 0 Disconnect and reconnect the USB memory device. (v p. 82) 0 Mass storage class compatible USB memory devices are supported. 0 This unit does not support a connection through a USB hub. Connect the USB memory device directly to the USB port. 0 The USB memory device must be formatted to “FAT32” or “NTFS”. 0 Not all USB memory devices are guaranteed to work.
Contents Connections Playback Settings Tips Appendix Bluetooth cannot be played back Bluetooth devices cannot be connected to this unit. 0 The Bluetooth function in the Bluetooth device has not been enabled. See the Owner’s Manual of the Bluetooth device to enable the Bluetooth function. 0 Bring the Bluetooth device near to this unit. 0 The Bluetooth device cannot connect with this unit if it is not compatible with the A2DP profile.
Contents Connections Playback Settings Tips Appendix The sound is cut off. 0 Bring the Bluetooth device near to this unit. 0 Remove obstructions between the Bluetooth device and this unit. 0 To prevent electromagnetic interference, locate this unit away from microwave ovens, wireless LAN devices and other Bluetooth devices. 0 Reconnect the Bluetooth device. The sound is cut off or noise occurs when using Bluetooth headphones. 0 Move the Bluetooth headphones closer to this unit.
Contents Connections Playback Settings Tips Appendix The Internet radio cannot be played back A list of broadcasting stations is not displayed. 0 The LAN cable is not properly connected, or the network is disconnected. Check the connection status. (v p. 85) 0 Perform the network diagnostic mode. Internet Radio cannot be played. 0 The selected radio station is broadcasting in a format that is not supported by this unit. Formats that can be played back in this unit are MP3, WMA and AAC. (v p.
Contents Connections Playback Settings Tips Appendix Music files on PC or NAS cannot be played back Files stored on a computer cannot be played. 0 Files are stored in a non-compatible format. Record in a compatible format. (v p. 312) 0 Files that are copyright protected cannot be played on this unit. 0 The USB port of this unit cannot be used for connection to a computer. 0 Media sharing settings on the server or NAS do not allow this unit. Change the settings to allow this unit.
Contents Connections Playback Settings Tips Appendix Various online services cannot be played Various online services cannot be played. 0 The online service may have been discontinued. The HDMI Control function does not work The HDMI Control function does not work. 0 Check that “HDMI Control” in the menu is set to “On”. (v p. 198) 0 You cannot operate devices that are not compatible with the HDMI Control function.
Contents Connections Playback Settings Tips Appendix Cannot connect to a wireless LAN network Cannot connect to the network. 0 The network name (SSID), password and encryption setting have not been set up correctly. Configure the network settings according to the setting details of this unit. (v p. 248) 0 Shorten the distance from the wireless LAN access point and remove any obstructions to improve access first before re-connecting again.
Contents Connections Playback Settings Tips Appendix When using HDMI ZONE2, the devices does not function properly When using MAIN ZONE, video output is interrupted in HDMI ZONE2. 0 With the same input source selected for MAIN ZONE and ZONE2, when you operate MAIN ZONE, video may be interrupted in HDMI ZONE2. When using HDMI ZONE2, no video or audio is output from the TV in ZONE2. 0 Check that the power is on for ZONE2. (v p. 172) 0 Check the input source for ZONE2. (v p.
Contents Connections Playback Settings Tips Appendix Update/upgrade error messages If an update/upgrade is interrupted or fails, an error message appears. Display Description Connection failed. Please check your network, then try The network connection is unstable. again. Connection to the server failed. Check your network environment and try the update again. Update failed. Please check your network, then try again. The download of the firmware failed.
Contents Connections Playback Settings Tips Appendix Resetting factory settings If the indicators are incorrect or the unit cannot be operated, restarting the unit may improve the problem. We recommend restarting the unit before returning the settings to the default settings. (v p. 281) If the operations are not improved by restarting the unit, follow the steps below. Various settings are reset to the factory default values. Make settings again. X 1 2 GAME 3 .
Contents Connections Playback Settings Tips Appendix Resetting network settings If network contents cannot be played or the unit cannot connect to the network, restarting the unit may improve the problem. We recommend restarting the unit before returning the settings to the default settings. (v p. 281) If the operations are not improved by restarting the unit, follow the steps below. Network settings are reset to the factory default values. Make settings again.
Contents Connections Playback Settings Tips Appendix About HDMI HDMI is an abbreviation of High-Definition Multimedia Interface, which is an AV digital interface that can be connected to a TV or amplifier. With the HDMI connection, high definition video and high quality audio formats adopted by Blu-ray Disc players (Dolby Digital Plus, Dolby TrueHD, DTS-HD, DTS-HD Master Audio) can be transmitted, which is not possible with the analog video transmission.
Contents Connections Playback Settings 0 Auto Lip Sync This function transmits audio signals from the TV to this unit through the HDMI cable and plays back the audio from the TV on this unit based on the HDMI Control function. If a TV without the ARC function is connected via HDMI connections, video signals of the playback device connected to this unit are transmitted to the TV, but this unit can not play back the audio from the TV.
Contents Connections Playback Settings Tips Appendix o Supported audio formats 0 VRR (Variable Refresh Rate): VRR reduces or eliminates lag, stutter and frame tearing for more fluid and better detailed gameplay.
Contents Connections Playback Settings Tips Copyright protection system In order to play back digital video and audio such as BD video or DVD video via HDMI connection, both this unit and the TV or player must to support the copyright protection system known as HDCP (Highbandwidth Digital Content Protection System). HDCP is copyright protection technology comprised of data encryption and authentication of the connected AV devices. This unit supports HDCP.
Connections Contents Playback Settings Tips Appendix Video conversion function This unit automatically converts the input video signals as shown in the diagram before outputting them to the TV.
Connections Contents Playback Settings Tips Appendix . This unit can convert the input video signals to the resolution that is set for “Resolution” in the menu before outputting them to the TV. (v p.
Contents Connections Playback Settings Tips Appendix Playing back a USB memory devices 0 This unit is compatible with MP3 ID3-Tag (Ver. 2) standard. 0 This unit can show the artwork that was embedded by using MP3 ID3-Tag Ver. 2.3 or 2.4. 0 This unit is compatible with WMA META tags. 0 If the image size (pixels) of an album artwork exceeds 500 × 500 (WMA/MP3/Apple Lossless/DSD) or 349 × 349 (MPEG-4 AAC), then music may not be played back properly.
Contents Connections Playback Settings The limits on the number of folders and files that can be displayed by this unit are as follows. Media Number of folder directory levels z1 8 levels 500 filesz2 5000 Number of This unit supports the following Bluetooth profile. 0 A2DP (Advanced Audio Distribution Profile): When a Bluetooth device that supports this standard is connected, monaural and stereo sound data can be streamed at a high quality.
Contents Connections Playback Settings Tips Appendix Playing back a file saved on a PC or NAS 0 This unit is compatible with MP3 ID3-Tag (Ver. 2) standard. 0 This unit can show the artwork that was embedded by using MP3 ID3-Tag Ver. 2.3 or 2.4. 0 This unit is compatible with WMA META tags. 0 If the image size (pixels) of an album artwork exceeds 500 × 500 (WMA/MP3/WAV/FLAC/Apple Lossless/DSD) or 349 × 349 (MPEG-4 AAC), then music may not be played back properly.
Contents Connections Playback Settings Tips Appendix Playing back Internet Radio Personal memory plus function o Playable broadcast station specifications The most recently used settings (input mode, HDMI output mode, sound mode, tone control, channel level, MultEQ® XT32, Dynamic EQ, Dynamic Volume, M-DAX and audio delay, etc.) are saved for each input source. Sampling frequency WMA 32/44.1/48 kHz MP3 32/44.1/48 kHz MPEG-4 AAC 32/44.
Contents Connections Playback Settings Tips Appendix Explanation of terms o Audyssey Audyssey LFC™ (Low Frequency Containment) Audyssey LFC™ solves the problem of low frequency sounds disturbing people in neighboring rooms or apartments. Audyssey LFC™ dynamically monitors the audio content and removes the low frequencies that pass through walls, floors and ceilings. It then applies psychoacoustic processing to restore the perception of low bass for listeners in the room.
Contents Connections Playback Settings o Auro-3D o Dolby Auro-3D® Dolby Atmos The technology suite is a groundbreaking new audio technology that combines height-based listening formats with powerful creative tools to deliver an unrivaled three-dimensional sound experience. Auro-3D® is the general format name for Sound in 3D and its related speaker lay-outs.
Contents Connections Playback Settings Tips Appendix Dolby Digital Dolby Speaker Technology (Dolby Atmos Enabled speakers) Dolby Digital is a multi-channel digital signal format developed by Dolby Laboratories. A total of 5.1-channels are played: 3 front channels (“FL”, “FR” and “C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for low frequency effects.
Contents Connections Playback Settings Tips Appendix o DTS Speaker Virtualizer Dolby Atmos height virtualization is a digital signal processing solution that leverages Dolby’s deep understanding of human audio perception to create the sensation of overhead sound from the listener-level speakers. This signal processing applies height-cue filters to overhead audio components contained within the audio signal before they are mixed into the listener-level speakers.
Contents Connections Playback Settings Tips Appendix DTS-ES™ Discrete 6.1 DTS-HD High Resolution Audio DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format adding a surround back (SB) channel to the DTS digital surround sound. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder.
Contents Connections Playback Settings Appendix o Audio DTS Neural:X Enables an immersive audio experience for older content. DTS Neural:X can upmix your stereo, 5.1 or 7.1 content to take full advantage of all speakers in your surround sound system. Apple Lossless Audio Codec This is a codec for lossless audio compression method developed by Apple Inc. This codec can be played back on iTunes, iPod or iPhone.
Contents Connections Playback Settings Tips Appendix THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Contents Connections Playback Settings Tips Appendix MPEG (Moving Picture Experts Group), MPEG-2, MPEG-4 Speaker impedance These are the names for digital compression format standards used for the encoding of video and audio. Video standards include “MPEG-1 Video”, “MPEG-2 Video”, “MPEG-4 Visual”, “MPEG-4 AVC”. Audio standards include “MPEG-1 Audio”, “MPEG-2 Audio”, “MPEG-4 AAC”. This is an AC resistance value, indicated in Ω (ohms). Greater power can be obtained when this value is smaller.
Contents Connections Playback Settings Tips Appendix o Video o Network ISF AirPlay ISF (Imaging Science Foundation) is an organization that certifies video technicians who are then qualified to carry out calibration and adjustment to match the installation conditions. It also sets quality standards for the optimization of device video performance. AirPlay sends (plays) contents recorded in iTunes or on an iPhone/iPod touch/iPad to a compatible device via the network.
Contents Connections Playback Settings Tips Appendix o Others WPA-PSK/WPA2-PSK (Pre-shared Key) This is a simple authentication system for mutual authentication when a preset character string matches on the wireless LAN access point and client. HDCP When transmitting digital signals between devices, this copyright protection technology encrypts the signals to prevent content from being copied without authorization.
Contents Connections Playback Settings Tips Appendix . Trademark information . Manufactured under license from Audyssey Laboratories™. U.S. and foreign patents pending. Audyssey MultEQ® XT32, Audyssey Dynamic EQ®, Audyssey Dynamic Volume® and Audyssey LFC™ are registered trademarks of Audyssey Laboratories. Front panel Display Rear panel . Apple, AirPlay, iPad, iPad Air, iPad Pro and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
Connections Playback Settings Tips Appendix . . Contents The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by D&M Holdings Inc. is under license. Other trademarks and trade names are those of their respective owners. . For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc.
Connections Playback Settings Tips . Contents . Manufactured under license from IMAX Corporation. IMAX® is a registered trademark of IMAX Corporation in the United States and/or other countries. All Rights Reserved. For DTS patents, see http:// patents.dts.com. Manufactured under license from DTS, Inc. DTS, the Symbol, DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries © DTS, Inc. All Rights Reserved.
Contents Connections Playback Settings Tips Specifications o Audio section 0 Analog Input sensitivity: 200 mV Frequency response: 10 Hz – 100 kHz — +1, –3 dB (Direct mode) S/N: 105 dB (IHF–A weighted, Direct mode) Distortion: 0.005 % (20 Hz – 20 kHz) (Direct mode) Rated output: Unbalanced RCA pre-output: 1.2 V Balanced XLR pre-output: 2.4 V 0 Digital D/A output: Rated output — 2 V (at 0 dB playback) Total harmonic distortion — 0.
Contents Connections Playback Settings Tips o Video section 0 Standard video connectors Input/output level and impedance: 1 Vp-p, 75 Ω/ohms Frequency response: 5 Hz – 10 MHz — 0, –3 dB 0 Color component video connector Input/output level and impedance: Y signal — 1 Vp-p, 75 Ω/ohms PB / CB signal — 0.7 Vp-p, 75 Ω/ohms PR / CR signal — 0.
Contents Connections Playback Settings Tips Appendix o Wireless LAN section Network type (wireless LAN standard): Conforming to IEEE 802.11a/b/g/n (Wi-Fi® compliant) z1 Security: WEP 64 bit, WEP 128 bit WPA/WPA2-PSK (AES) WPA/WPA2-PSK (TKIP) Used frequency range: 2.4 GHz, 5 GHz z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo are registered trademarks of the Wi-Fi Alliance. o Bluetooth section Communications system: Bluetooth Specification Version 4.
Contents Connections Playback Settings Tips o General Operating temperature: 41 °F - 95 °F (5 °C - 35 °C) Power supply: AC 120 V, 60 Hz Power consumption: 60 W Power consumption in standby mode: 0.2 W z Power consumption in CEC standby mode: 0.5 W z When “Network Control” in the menu is set to “Off In Standby” and “HDMI Pass Through” is set to “Off”. For purposes of improvement, specifications and design are subject to change without notice.
Contents Connections Playback Settings Tips Appendix 16.2 (412) 1.6 (40) 0.7 (18) 2.1 (53) 10.4 (267) 16.2 (411) 14.2 (361) 1.6 (40) 0.5 (12) 1.3 (32) o Dimensions (Unit : in. (mm)) 2.4 (60) 13.3 (340) 9.7 (247) 7.3 (185) 2 (50) . 2 (50) 0.6 (14) 6.7 (171) 17.3 (440) o Weight: 22.9 lb (10.
Contents Connections Index Playback Settings vB v Numerics 11.1-channel .................................................. 63 3D ................................................................ 304 4K/8K ........................................................... 304 5.1-channel .............................................. 41, 51 7.1-channel .............................................. 41, 52 9.1-channel .................................................... 56 AirPlay .............................
Contents Connections vM Playback Settings Menu map .................................................... 174 Muting ............................................................ 92 vN Queue ............................................ 94, 116, 123 Rear panel ...................................................... 27 NAS ............................................................. 115 Resetting factory settings ............................. 302 Network settings .......................................
Contents Connections Playback Settings Tips vW Web control .................................................. 167 Wi-Fi settings ............................................... 247 Wired LAN .............................................. 85, 246 Wireless LAN ......................................... 86, 247 vZ ZONE2/ZONE3 ............................................
. 3520 10757 00AMA ©2020 Sound United. All Rights Reserved.
ENGLISH FRANÇAIS ESPAÑOL AV Pre Tuner AV7706 Quick Start Guide Check our AVR setup tips online Guide de démarrage rapide / Guía de inicio rápido Read Me First.... Lisez-moi en premier.... / Lea esto primero.... Us.Marantz.com/SetupTips Ca.Marantz.com/SetupTips Please do not return this unit to the store. If you need help… Call for Assistance 1-855-ONE-Marantz (USA) 1-855-663-6272 1-800-668-0652 (Canada) Monday – Friday 10:00AM to 10:00PM E.S.T Saturday 12:00PM to 8:00PM E.S.
Welcome Before You Begin Required for Setup Thank you for choosing a Marantz Pre Tuner. This guide provides step-by-step instructions for setting up your Pre Tuner. or TV RCA cables HDMI cable XLR cables Power amplifier Speakers / Speaker cables Optional or LAN cable Wi-Fi router • When connecting this unit to a device that is compatible with the Deep Color, 4K, ARC and eARC functions, use a “High Speed HDMI cable with Ethernet” that displays the HDMI logo.
What’s In the Box Quick Start Guide FM indoor antenna Safety Instructions AM loop antenna Notes on radio Sound calibration microphone Warranty (for USA / for CANADA) Sound calibration microphone stand Cable labels Remote control unit (RC044SR) Pre Tuner R03/AAA batteries Power cord External antennas for Bluetooth/ wireless connectivity • The included sound calibration microphone stand is convenient for use when performing Speaker Calibration.
Important: External Antennas The removable external antennas are required for both Bluetooth and Wireless network connectivity. Please make sure to connect the antennas before attempting to use the Bluetooth or Wi-Fi features of the AV7706. n Connecting the external antennas for Bluetooth/Wireless connectivity For each of the two antennas: q Place the antenna evenly over the antenna terminal located at the upper left or right corner of the rear panel.
Setup Installing batteries in the There are four steps to the setup process. 1 Installing batteries in the remote control unit 2 Connecting the Pre Tuner, Power Amplifier and your TV 3 Following the On-Screen Setup Assistant 1 remote control unit Batteries 4 Downloading the Mobile Apps 4 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
2 Connecting the Pre Tuner, Power Amplifier and your TV 1) Place the Pre Tuner and Power Amplifier near your TV and connect the power cord TV TV Pre Tuner Power cord (supplied) Pre Tuner Connect to household power outlet (AC 120 V, 60 Hz) Power Amplifier 5 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
2) Connect the Pre Tuner to your home network Wired LAN Wireless LAN Connect an Ethernet cable (not included) between your Pre Tuner and your network router. When connecting to wireless LAN (Wi-Fi), follow the instructions in “Connecting the external antennas for Bluetooth/Wireless connectivity” and connect the antennas. To LAN port Router 6 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
3) Connect the Pre Tuner to your TV with an HDMI cable 4) Turn on the TV HDMI IN (ARC) HDMI cable 1 OR NIT ARC C MO AR e HDMI OUT MONITOR 1 (ARC/eARC) TV remote control unit 5) Select the appropriate HDMI input on your TV HDMI Pre Tuner (Rear panel) ARC (Audio Return Channel) and eARC (Enhanced Audio Return Channel) support: If your TV supports ARC, your TV can send audio back to the AV receiver when you are using your TV’s built-in video sources (TV tuner, Smart TV streaming services, etc.
6) Turn on the Pre Tuner • Press X to turn on the Pre Tuner. 7) Verify the connection • Verify that you can see this screen on your TV. AV Preamp Setup Assistant P l e a s e s e l e c t a l a ng ua ge ... English Français Español If this screen is not displayed, please go back and retry the steps again in the recommended sequence. 8 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
3 Following the On-Screen Setup Assistant Now TV is connected to the receiver. The Setup Assistant will walk you through connecting and configuring your Power Amplifier and components to your Marantz Pre Tuner. Please use the remote control and follow the on-screen instructions. AV Preamp Setup Assistant Please select a language... English Français Español 9 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
4 Downloading the Mobile Apps Download both the “HEOS” App and the “Marantz 2016 AVR Remote” App for the full home entertainment experience. The HEOS App is required to access online music through your Pre Tuner. Marantz 2016 AVR Remote HEOS The HEOS App allows you to explore, browse, and play music from many online streaming services or from your own music library. Control your new Pre Tuner with the latest Marantz 2016 AVR Remote App.
Owner’s Manual • For more information, visit www.marantz.com • Refer to the Online Manual for other functions information and operation procedure details. manuals.marantz.com/AV7706/NA/EN/ Online Manual 11 Printing Color : Black 1. AV7706U_QSG_ENG_00A_200702.
Printed in Vietnam 5411 11833 00AM © 2020 Sound United. All Rights Reserved. Printing Color : Black 4. AV7706U_QSG_BackPage_00A_200702.
Cable labels Kabel ken nzeich nu ng Etiquette du cable Etichetta cavo Etiquetas de cables Kabel label Kabeletikett HpllblK Ka6enfl Etykieta kabla 7.
~------------------------------------------------------------------------------------------------------------------------------------------------------------------, I L TOP FRONT TOP FRONT L TOP SURROUND I ! TOP SURROUND R TOP FRONT I ! TOP FRONT R TOP MIDDLE R TOP REAR R SURROUND HEIGHT R REAR HEIGHT R FRONT DOLBY R SURROUND DOLBY R BACK DOLBY R I I L TOP MIDDLE TOP MIDDLE L R TOP MIDDLE ! I I TOP REAR L TOP REAAL TOP REAR R ! I I SURROUND HEIGHT L SURROUND H
AV7706 11.2Ch 8K Ultra HD AV Surround Pre-Amplifier with HEOS® Built-in and Voice Control Featuring 11.2 channel XLR and RCA pre-outs, the Marantz AV7706 supports all 3D audio formats including Dolby Atmos®, Dolby Atmos Height Virtualization, DTS:X®, DTS Virtual:X™, IMAX Enhanced®, and Auro-3D®. Enjoy audio playback with exceptional quality thanks to Marantz-proprietary HDAM modules and stream from Amazon Music HD, Pandora, Spotify, TIDAL, Deezer, and more with HEOS® Built-in. • 11.
AV7706 Technical Specs Multichannel surround DTS HD Master / DTS:X / DTS:X Pro •/•/- DTS Virtual:X IMAX Enhanced • • Dolby ProLogic Ilz / Dolby Surround -/• DTS Neo:X / DTS Neural:X Dolby TrueHD / Dolby Atmos / Dolby Atmos Height Virtualization Auro 3D Multichannel Stereo max. number of processing (preamp) channels Sound Enhancements -/• •/•/• • • 11.
Microphone Stand Assembly Instructions 1 Montageanleitung Mikrofonstander Instructions d'assemblage du support de microphone lstruzioni per il montaggio del supporto microfono lnstrucciones de montaje del soporte del micr6fono 2 Montage-instructies Microfoonstatief Monteringsanvisning for mikrofonstall -x 1? ;z 1;1 ::-- t-:'*EIJ:I.rz:-rmBfl• ~:R:JXt~~m~t~aJl li1HCTPYKLIIH1 no c6opKe CTOiiiKI1 nOA M11KpOOH lnstrukcje montai:u stojaka na mikrofon 3 ------------..:.
For U.S.A. ■na•antz® Limited Warranty Marantz America, Inc. ("Marantz") warrants the following Marantz Products for the periods indicated: 1. The following Marantz AudioNideo components, have a 3 year warranty for both Parts & Labor, from the original Who may enforce the warranty This warranty extends only to the original purchaser, not subsequent owners.
For CANADA maa-antz® MARANTZ CANADA LIMITED WARRANTY Marantz Canada ("Marantz") warrants the following Marantz products for the periods indicated: Who May Enforce the Warranty 3-year warranty for both Parts & Labour, from the original purchase date: What We Will Pay For Amplifiers; Pre Amplifiers; Pre Amplifier-Processor-Tuners; Integrated Amplifiers; AV Pre Tuner; Tuners; Receivers; AV Surround Receiver; Blu-ray DVD Super Audio CD/CD Players/ Changers; CD Receiver; Turntable; Network Audio Player; DIA
Notes on radio USA CANADA FCC Information (For US customers) IC Information (For Canadian customers) 1. COMPLIANCE INFORMATION • Product Name: AV Surround Receiver/ AV Surround Amplifier/ AV Pre Tuner/ AV Pre Amplifier • Model Number: NR1711 / SR5015 / SR6015 / SR7015 / SR8015 / AV7706 • CONTAINS TRANSMITTER MODULE FCC ID: RAX-AIOS4-0S 1. PRODUCT CONTAINS TRANSMITTER MODULE IC: 4711A-AIOS40S This product complies with RSS rules of Industry Canada.
n1arantz · CE [ENGLISH] 1. DECLARATION OF CONFORMITY [SVENSKA] 1. OVERENSSTAMMELSESINTYG Hereby, (D&M Holdings Inc.( declares that our product is in compliance with following EU/EC Directives. The full text of the EU declaration of conformity is available at the following internet address: 2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets RE directive requirements.
Safety Instructions tnarantz . (Read these safety instructions before operating the unit.) 0 SAFETY PRECAUTIONS CAUTIONS ON INSTALLATION CAUTION: To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
CAUTION (FOR AMPLIFIER): HOT SURFACE. DO NOT TOUCH. The top surface over the internal heat sink may become hot when operating this product continuously. Do not touch hot areas, especially around the "Hot surface mark" and the top panel. PRECAUTION (POUR AMPLIFICATEUR): SURFACE CHAUDE. NE PAS TOUCHER. La surface superieure du dissipateur de chaleur peut devenir chaude si vous utilisez ce produit en continu.
CAUTIONS ON USING BATTERIES AVISOS SOBRE DE LAS PILAS There is a possibility of smoke, fire, explosion from the battery, Please note as following. • Insert the specified batteries in the remote control unit. • Replace the batteries with new ones if the set does not operate even when the remote control unit is operated close to the unit. (The supplied batteries are only for verifying operation. Replace them with new batteries at an early date.
Marantz with HEOS Built-in. Any song. Any Room. Indoors or Out. What is HEOS? Qu'est-ce que HEOS? HEOS is a smart. wireless music streaming technology built into your Marantz product. It uses your home network and the HEOS app to play your favorite music anywhere in your home. HEOS ist ein kabelloses Musiksystem, mit dem Sie lhre gesamte Musik muhelos von 0berall im Haus steuern. Sie benotigen lediglich einen oder mehrere HEOS Lautsprecher und die kostenlose App.
Unlock the Magic of Unlimited Hi-Res Listening ~ ......... • 2 ±I I 3 ~ Spoti,..,. w ,y ·111·1 1 HEOS APP amazon music ...__.., c:::]O pandora ~ .
Fi CERTIFIED
