ITALIANO NEDERLANDS DEUTSCH FRANÇAIS ENGLISH AV Pre Tuner AV8003 AV8003N.indb 3 08.4.
ENGLISH DEUTSCH WARRANTY For warranty information, contact your local Marantz distributor. GARANTIE Bei Garantiefragen wenden Sie sich bitte an Ihren Marantz-Händler. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz.
CE MARKING English The AV8003 is in conformity with the EMC directive and low-voltage directive. Français Le AV8003 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell AV8003 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Nederlands De AV8003 voldoet aan de EMC eisen en de vereisten voor laag-voltage. Italiano Il AV8003 è conforme alle direttive CEE ed a quelle per i bassi voltaggi.
Deutsch Nederlands Italiano WARNHINWEISE - Das Gerät nicht Regen, Feuchtigkeit, Tropf- oder Spritzwasser aussetzen. - Die Abdeckung nicht vom Gerät abnehmen. - Keine Gegenstände durch die Belüftungsschlitze stecken. - Das Netzkabel nicht mit feuchten oder nassen Händen anfassen. - Decken Sie die Lüftungsöffnungen nicht mit einem Tischtuch, einer Zeitung, einem Vorhang usw. ab. - Es dürfen keine Gegenstände mit offener Flamme, wie etwa brennende Kerzen, auf dem Gerät aufgestellt werden.
ENGLISH INTRODUCTION A NOTE ABOUT RECYCLING Thank you for purchasing the Marantz AV8003 AV Pre tuner. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the AV8003. As there are a number of connection and configuration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer.
ENGLISH NAMES AND FUNCTION TABLE OF CONTENTS FEATURES CONNECTIONS INTRODUCTION ....................................1 BASIC OPERATION ............................38 REMOTE CONTROLLER OPERATION ..54 ACCESSORIES CHECK ....................................................1 SELECTING AN INPUT SOURCE ...................................38 GENERAL INFORMATION OF RC2001 TO THE UNIT ..54 TABLE OF CONTENTS .........................2 SELECTING THE SURROUND MODE...........................
ENGLISH • HDMI HDMI (High-Definition Multimedia Interface) is an enhancement to the DVI (Digital Visual Interface) standard. It adds capabilities for digitally transmitting audio signals in addition to video signals. Where multiple cables were previously needed for audio/ video, HDMI enables audio/video connection via a single cable. The HDMI input jacks of this unit support HDMI Ver. 1.3a. and the HDMI output jacks of this transmitter support HDMI Ver. 1.3a.
ENGLISH OPERATION OF REMOTE CONTROLLER REMOTE CONTROL Operate the remote controller within a distance of approx. 5m from the infrared receptor window on the front of the unit. LOADING BATTERIES Before using the remote controller for the first time, load the batteries in the remote controller. The batteries provided are used to verify the operations of the remote controller only. 1. 5 rox. Remove the back cover. m App Rechargeable batteries can also be used.
FRONT PANEL o !0 UP PURE DIRECT DOWN INPUT SELECTOR SURROUND MODE VOLUME AUTO PURE DIRECT ZONE ZONE SPEAKER MENU EXIT 7.1CH INPUT THX BAND TOP T-MODE M-DAX MEMORY @2 !1 Press this button to select THX processing for input source. CLEAR !2 SETUP MIC ENTER q POWER switch and STANDBY indicator Press the button to turn the power ON, and press again to turn it OFF.
ENGLISH PCM This indicator is illuminated when the input signal is PCM (pulse code modulation). 2 SURROUND This indicator is illuminated when a Dolby Surround signal is input. NAMES AND FUNCTION FL DISPLAY AND INDICATER f s a d DISP MULTI CONNECTIONS SLEEP h AUTO TUNED AUTO SURR DIRECT k l ¡1 ¡3 ¡0 ¡2 j g ST V – OFF DISC 6.1 NIGHT PEAK MTX 6.
SR FM (75 75Ω Ω) GND INPUT 3( 3(VCR1 VCR1)) Y CB/ PB C R/ PR CB/ PB Y DVD((2) DVD VCR1((3) VCR1 SBR MONITOR OUT ZONE OUT 2 1 L OUTPUT 1 TV((1) TV DVD(2) DVD( 1 2 SL CONNECTION 1 GND 2 HOT(+) 1 2 3 3 COLD(-) OUTPUT 2 VCR1((3) VCR1 IN OUT DSS/VCR2(4) DSS/VCR2( IN OUT C 3 3 2 3 1 2 1 u 3 2 SR 3 2 1 2 MONI. OUT SBR UNBALANCED SBL SW BALANCED C NETWORK PRE OUT 4 IN 5 OUT 6 IN S-VIDEO OUT REMOTE CD/CDR BALANCED IN DC OUT COAX.
ENGLISH NAMES AND FUNCTION @1 AUDIO IN/OUT (TV, DVD, VCR1, DSS/VCR2, TAPE, CD/CDR) CONNECTIONS These are the analog audio inputs and outputs. There are 6 audio inputs and 4 audio outputs. The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD players and etc.... The audio inputs and outputs require RCA-type connectors. @2 SETUP BASIC OPERATION @3 z x c v b n . m , ADVANCED OPERATION .
(When Zone D (MAIN ZONE) mode is selected) These buttons are used to turn on or off, for the unit in main zone. (When Zone D (MAIN ZONE) mode is selected) These buttons are used to mute the audio for the unit in main zone. ⁄1 x n (When Tuner mode (T1) is selected) SOURCE ON button This button is used to select the screen resolution. c ⁄4 b n ⁄3 ⁄2 AMP - SOURCE /Numeric buttons SOURCE buttons These buttons are used to switch the source of the unit.
ENGLISH NAMES AND FUNCTION CONNECTIONS SPEAKER PLACEMENT CONNECTIONS SETUP BASIC OPERATION ADVANCED OPERATION The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back left and right speakers, and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units.
CONNECTION TO AN MM8003 (BALANCED) CONNECTION TO AN MM8003 (UNBALANCED) Connect the L (front left), R (front right), C (center), SL (Surround left), SR (Surround right), SBL (Surround back left), and SBR (Surround back right) terminals to the unbalanced input terminals of a power amp such as the MM8003. CONNECTING A SUBWOOFER CONNECTING A SUBWOOFER Use the SW jack to connect a powered subwoofer (power amplifier built in ). Use the SW jack to connect a powered subwoofer (power amplifier built in ).
ENGLISH CONNECTING AUDIO COMPONENTS CONNECTIONS 1. European system (Pin w = HOT, Pin e = COLD) HOT w q e CD recorder Super Audio CD ANALOG ANALOG OUTPUT INPUT L L R R R L Analog Audio Analog Audio (balanced) Digital Audio (coaxial) DIGITAL DIGITAL INPUT OUTPUT BALANCED L UNBALANCED L R L R • The balanced output connector uses a XLR connector. • The XLR connector for professional use is internally wired in either of the following two systems.
ENGLISH R Component jack Make component video connections to a TV or monitor with component inputs to produce higher quality video images. Use a component video cable or 3 video cords to connect the component video out jacks on the unit to the monitor.
ENGLISH NAMES AND FUNCTION DVD player CONNECTING HDMI COMPONENTS HDMI JACK CONNECTIONS This unit has four HDMI inputs and two HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. This unit is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output. Select an input source from the OSD menu system.
ENGLISH CONNECTING THE REMOTE CONTROL JACKS INPUT 1 1((TV TV)) NAMES AND FUNCTION CONNECTING MULTI CHANNEL AUDIO COMPONENTS INPUT 2 2((DVD DVD)) OUT OU PUT PU 1 R OUT PUT 1 FM (75 75Ω Ω) L GND ANTENNA SR SL INPUT 1 1((TV TV)) CR/ PR INPUT 3(VCR1 VCR1)) UT 3( Y CB/ CR/ PR PB CB/ PB Y CR/ SBR PR SBL TV(1) TV( INPUT 4 4((DSS / VCR2 VCR2)) INPUT T 4( 4(DSS/VCR2 DSS/VCR2)) OUTPUT 1 TV(1) TV( DVD(2) DVD( VCR1((3) VCR1 IN OUT DSS/VCR2(4) DSS/VCR2( IN OUT CB/ PB CR/ PR CB/ PB Y
ENGLISH NAMES AND FUNCTION CONNECTING THE SUPPLIED ANTENNAS CONNECTING THE ANTENNA TERMINALS FM Antenna AM Loop Antenna FM External Antenna Connecting the supplied FM antenna The supplied FM antenna is for indoor use only. During use, extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion.
ENGLISH As shown in the diagram, a player connected to this unit in another ZONE can be used to play music and movies when used in combination with an amp from Marantz or other manufacturer. If Surround back speakers or SPEAKER C are not being used, the Surround Back Preout terminals can be used for the ZONE SPEAKER terminals.
ENGLISH NAMES AND FUNCTION CONNECTING FOR SPEAKER C USE (BI-AMP CONNECTION) A bi-amp connection is possible with speakers that have two sets of inputs (for treble and bass). This allows you to drive the treble and bass units with separate channel amps, which enables better sound quality. Connect the speakers as shown in the figure. Set the SPEAKER C selector switch on the rear panel to ON.
ENGLISH As shown in the diagram, music, images, and movie files stored on a network device can be played by connecting to a network device such as a router or a hub. Use a LAN cable when connecting a network device to the NETWORK terminal of this unit. For settings necessary to use the network and method of operation, see the NETWORK User Guide.
ENGLISH NAMES AND FUNCTION SETUP RC2001 BUTTON CONTROL HOME button After all components are connected, initial setup must be performed. CONNECTIONS ONSCREEN DISPLAY MENU SYSTEM SETUP This unit incorporates an onscreen menu system, which makes various operations possible by using the cursor (3, 4, 1 , 2) and ENTER buttons on the remote controller or on the front panel.
Note: • After you complete this portion of the setup, move cursor to “RETURN” with the 3, 4, 1 and 2 cursor buttons and press the ENTER button. • Press the TOP button on this unit to return to the top screen of the main menu while setting setup items. SUB MENU NAMES AND FUNCTION ENGLISH MAIN MENU RETURN 7.NETWORK LOCKED VIDEO RESOLUTION UNLOCK SCREEN NEXT EXIT SETUP CONNECTIONS 1.INPUT SETUP 2.SPKR SETUP 3.SURR SETUP 4.VIDEO SETUP 5.PREFERENCE 6.ACOUSTIC EQ 7.
ENGLISH NAMES AND FUNCTION 1.INPUT 1 INPUT SETUP FUNC This menu is for setting the matching the output of connected audio devices and the input jacks of this unit. 7.1CH CONNECTIONS • FUNC RENAME : “1-3 FUNCTION RENAME” (see page 24) SETUP 1. Select “1. INPUT SETUP” from the MAIN MENU with 3 or 4 cursor button, and press the ENTER button. 1.INPUT FUNC BASIC OPERATION 7.1CH INPUT INPUT FUNCTION RETURN SETUP ☞ P. 23 NEXT EXIT ☞ P.
:AUTO :AUTO :AUTO :AUTO RETURN 2. 1 2 3 4 1 2 3 4 NEXTT 1 2 3 4 1 2 3 4 Press the ENTER button. EXIT Select a setting with the 3, 4, 1, and 2 cursor buttons, and assign a mode and input jack (DIG, HDMI, COMP, V/S). HDMI: Select “HDMI”, when only a HDMI signal will be used. DIG: Select “DIG”, when only a digital signal will be used. ANA: Select “ANA” for input sources for which no digital input jacks are used. DIG The 6 digital inputs can be assigned to a desired source.
ENGLISH NAMES AND FUNCTION 1-3 FUNCTION RENAME 9. CONNECTIONS Input sources can be registered under any name. This menu is for renaming input source. This menu is for renaming function name. Names can be up to 10 characters long, including spaces. (Characters are selected from those appearing on the display.) This name appears on the unit's FL display and the OSD, but it does not appear in the OSD Setup menu. 1. Select “FUNCTION RENAME” from the 1.
ENGLISH Select “2.SPKR SETUP” from the MAIN MENU with 3 or 4 cursor buttons and press the ENTER button. RETURN ☞ P. 26 ☞ P. 29 AUTO AUTO SETUP AUTO SETUP: START MAIN ZONE SURR BACK: 2CH NOW SETUP ANALYZING!! CANCEL RETURN EXIT AUTO RETURN AUTO SETUP SPEAKERS CHECK:-1st MIC POSITION NOW ANALYZING !! SETUP ______________ NOW CALCULATING! SETUP AUTO SETUP MANUAL SETUP AUDIO AUTO EXIT SPEAKERS 2.
ENGLISH NAMES AND FUNCTION 2-1 AUTO SETUP (MultEQ™ SETUP) The AUTO SETUP (MultEQ™ Setup) feature of the unit measures sound characteristics of the speaker system and room where the unit is used and automatically optimizes settings. CONNECTIONS SETUP The Audyssey MultEQ™ technology adopted by this unit provides the best listening environment for multiple listeners.
STORE Select items to check with the 3/4 cursor buttons and press the ENTER button to enter them. Note: To check equalizer (MultEQ) parameters, see page 37. [Example] Confirmation screen for speaker detection SPEAKER CONFIG CHECK !! SPEAKER FRONT : YES CENTER : NON FRONT R : YES SURR.R : YES SURR.B R : NON SURR.B L : NON SURR.L : YES SUB W : YES AUTO AUTO AUTO AUTO 11.
ENGLISH NAMES AND FUNCTION ERROR MESSAGES Displayed Error Cause MIC SET ERROR!! AUTO CONNECTIONS AUTO SETUP: START 2CH MIC SET SETUP AUTO SETUP SPEAKERS BASIC OPERATION • The speakers required for suitable playback were not detected. • Speaker polarity is connected backwards. • Check the speaker that is indicated as having reversed polarity ([REV] can appear with some speakers even when properly connected. In such case, ignore the error indication.
ENGLISH SPEAKER THX SPKR SUB W FRONT CENTER SURR. SURR.B SURR.B SIZE LPF/HPF BASS MIX RETURN SIZE : YES : YES : SMALL : SMALL : SMALL : 2CH : SMALL : 80Hz : MIX NEXT EXIT When setting the speaker size in the SPEAKER SIZE menu, use the guidelines below. LARGE: The complete frequency range for the channel you are setting will be output from the speaker. SMALL: Frequencies of the channel you are setting that are lower than approx. 80 Hz will be output from the subwoofer. If the SUB.
ENGLISH NAMES AND FUNCTION CONNECTIONS SUB W: Set the distance from the subwoofer to your normal listening position. SURR. B L: Set the distance from the surround back left speaker to your normal listening position. SURR. B R: Set the distance from the surround back right speaker to your normal listening position. SETUP BASIC OPERATION Notes: • Set the distance to each speaker in meters (m) or feet (ft) as follows. m: 0.03 - 9.15 m in 0.03 m steps ft: 0.1 - 30.0 ft in 0.
ENGLISH 3.SURR RETURN R L : : : : : : RETURN 0.0dB 0.0dB 0.0dB 0.0dB 0.0dB 0.0dB EXIT : : : OFF 0dB OFF NEXT RE-EQ: Turns THX Cinema Re-EQ™ on and off. Select the Cinema Re-EQ™ with the 1 or 2 cursor button to activate it. LFE LEVEL: Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal. Select “0dB”, “–10 dB” or “OFF” with 1 or 2 cursor button. M-DAX: Select the desired M-DAX mode. Select “HIGH”, “LOW” or “OFF” with the 1 or 2 cursor button.
ENGLISH NAMES AND FUNCTION SUB W LEVEL: Set the effect level of the subwoofer speaker between –18 and +12 level in 0.5 level interval . • If “NONE” was selected for the subwoofer speaker setting in the SPEAKER SIZE, then this setting will not appear. CONNECTIONS Note: • Setting to a mode other than multichannel stereo or CSII will affect the speaker level as explained in “2-2 MANUAL SETUP”.
2. NEXT EXIT Select the desired menu with the 3/4 cursor buttons and press the ENTER button. • VIDEO CONVERT This unit is equipped to convert video signals for monitor output. This section explains how to set up conversion for each type of video input. 1. Select “4. VIDEO SETUP” from the MAIN MENU with the 3 / 4 cursor buttons and press the ENTER button. 2. Select “VIDEO CONVERT” with the 3 / 4 cursor buttons and press the ENTER button. VIDEO TV DVD VCR1 DSS TAPE CD/R AUX RETURN 3.
ENGLISH NAMES AND FUNCTION 5 PREFERENCE • ZONE SETUP : “5-1 ZONE SETUP” (see page 35) • DC TRIGGER SETUP : “5-2 DC TRIGGER SETUP” (see page 35) CONNECTIONS 1. Select “5. PREFERENCE” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 5.PREFERENCE ZONE SETUP DC TRIGGER SETUP STANDBY : AUDIO : HDMI AUDIO: HDMI LIP : P.AMP LINK: RETURN BASIC OPERATION 2.
3. Press the ENTER button to enter the setting. The following explanation shows how to operate ZONE A of the zone system. The ZONE B setting does not have the VIDEO FUNCTION. ZONE SETUP A VIDEO :DVD AUDIO :DVD SLEEP :OFF MONO/ST:STEREO OSD INFO:ENABLE ZONE:OFF SPKR: VOL :VARI VOL : LEV :-90dB LEV : RETURN 4. BACK EXIT Select the desired item with the 3 or 4 cursor button. VIDEO: Select the video source of the zone output with the 1 or 2 cursor buttons.
ENGLISH NAMES AND FUNCTION 3. 6 ACOUSTIC EQ This display is for setting up the equalizer and changing the Equalizer mode. CONNECTIONS • PRESET G. EQ ADJ : “6-1 PRESET G. EQ ADJ” (see page 37) • CHECK AUTO 1 & 2 : “6-2 CHECK AUTO” (see page 37) SETUP EQ MODE: There are 4 equalizer modes to choose from: PRESET G.
Select “PRESET G. EQ ADJ” with the 3 or 4 cursor buttons. 3. Press the ENTER button to enter the selection. PRESET RESET:CH CH :FL +9 0dB -20 63 250 1k 4k 125 500 2k RETURN ADJUST 63 125 250 500 1k 2k 4k 8k 16k 16k 8k Select “6. ACOUSTIC EQ” from MAIN MENU with the 3 or 4 cursor buttons and press the ENTER button. 2. 3. After you complete this portion of the setup, press the ENTER button to enter the settings. Move cursor to “RETURN” with the 3, 4 cursor buttons and press the ENTER button.
ENGLISH NAMES AND FUNCTION BASIC OPERATION SELECTING AN INPUT SOURCE 2. Before you can listen to any input media, you must first select the input source on the unit. 2. CONNECTIONS Example : DVD 1. (Using the unit) ≠ AV PRE TUNER AV8003 3. UP HDMI PURE DIRECT 3. M-DAX DOWN INPUT SELECTOR SETUP SURROUND MODE STANDBY VOLUME AUTO PURE DIRECT ZONE ZONE SPEAKER MENU EXIT 7.
OFF ↓ • NIGHT Mode OFF N I G H T OFF O F F Turn off the Night mode. ADJUSTING THE MAIN VOLUME AV PRE TUNER AV8003 3 UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR VOLUME SURROUND MODE STANDBY AUTO PURE DIRECT ZONE ZONE SPEAKER MENU EXIT T 7.1CH INPUT THX BAND TOP T-MODE M-DAX MEMORY CLEAR DISPLAY POWER ON/OFF PHONES SETUP MIC ENTER Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOL + / – buttons on the remote controller.
ENGLISH NAMES AND FUNCTION • For optimal video performance, THX recommends setting the “VIDEO CONVERT” mode “DISABLE”. CONNECTION EXAMPLE • When a monitor is connected to the HDMI MONITOR OUT terminal of the unit AV PRE TUNER AV8003 CONNECTIONS UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR VOLUME SURROUND MODE AUTO ZONE SPEAKER ZONE PURE DIRECT STANDBY MENU EXIT BAND 7.
DTS (Neo:6 Cinema) (Neo:6 Music) CSII Cinema CSII Music CSII Mono STEREO Dolby Virtual Speaker Multi Ch. Movie Music (O): Movie mode only.
ENGLISH NAMES AND FUNCTION CONNECTIONS SETUP AUTO EX/ES Dolby MODE dts When this mode is selected, the unit determines whether the digital input signal is Dolby Digital, Dolby Digital Surround EX, Dolby Digital Plus, Dolby TrueHD, DTS-HD, DTS, DTS-ES, DTS 96/24 or PCM audio. Surround EX & DTS-ES will operate for multichannel sources that have a Dolby Digital Surround EX or DTS-ES auto trigger flag in the digital signal.
This mode is used to create a wider, deeper and more natural soundstage from two channel source material. This is done by feeding the left channel signal to both the left front and left surround speakers and the right channel signal to both the right front and right surround speakers. Additionally, the center channel reproduces a mix of the right and left channels. Note: • Audio is not output from the CENTER channel when using MULTI CH. MUSIC mode.
ENGLISH NAMES AND FUNCTION ADVANCED OPERATION DISPLAY MODE CONNECTIONS DISP DISPLAY LISTENING THROUGH HEADPHONES This jack may be used to listen to the unit’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug. Note that the speakers will automatically be turned off when the headphone jack is in use.
LEVEL LEVEL :+10.0dB : 0.0dB DOLBY HP (Headphone) MODE can be selected with the left and right cursor buttons. BYPASS → DH (DOLBY Headphone) → BYPASS BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo. DH: Dolby Headphone is a signal processing system that delivers a sound similar to room speakers. It makes it possible to experience the volume and space of a 5-channel surround system using ordinary stereo headphones.
ENGLISH NAMES AND FUNCTION AUX INPUT TV AUTO ON/OFF FUNCTION CONNECTIONS If you don’t need to connect 7.1 Ch. input terminals with multi channel decoder, L(front left) and R (front right) inputs terminals are available as AUX input. In this case, You can connect additional audio source to AUX as other audio input terminals. AV PRE TUNER AV8003 This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the unit. AUTO POWER ON 1.
ENGLISH Recover backed up settings as follows. Hold the MEMORY and MENU buttons on the front panel simultaneously for at least 3 seconds. LISTENING TO THE TUNER TUNER OPERATION 3. 3. TO SELECTING THE TUNER AUTO TUNING 1. (Using the unit) AV PRE TUNER AV8003 NAMES AND FUNCTION RECOVERY OF MEMORY 3. 2. UP CONNECTIONS HDMI AV PRE TUNER AV8003 AV PRE TUNER AV8003 UP DOWN UP ZONE SPEAKER M-DAX MENU EXIT BAND T-MODE MEMORY CLEAR 2. 1. DOWN 7.
ENGLISH NAMES AND FUNCTION Note: The same operations performed using the 3/ 4 buttons can be performed using the – TUNE + button of item 002 when the remote controller is in TUNER mode. DIRECT FREQUENCY CALL (FM) TUNING MODE (AUTO STEREO OR MONO) AUTO, TUNED, ST T-MODE 3. 3. AV PRE TUNER AV8003 UP CONNECTIONS If tuning does not stop at the desired station, use to the “Manual Tuning” operation. PURE DIRECT HDMI DOWN INPUT SELECTOR MANUAL TUNING STANDBY 3.
No stored preset number will be skipped. 2. 2. 4. You can fast forward the preset stations, press the 2 cursor button continuously. 5. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P-SCAN button on the remote controller. AV PRE TUNER AV8003 UP HDMI M-DAX DOWN INPUT SELECTOR 4. (Using the unit) VOLUME ZONE ZONE SPEAKER MENU EXIT 7.1CH INPUT THX BAND TOP T-MODE M-DAX MEMORY 3. CLEAR 3. 1.
ENGLISH NAMES AND FUNCTION SORTING PRESET STATIONS NAME INPUT OF THE PRESET STATION. AV PRE TUNER AV8003 UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR SURROUND MODE CONNECTIONS STANDBY 5. This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation. The entry in this column is fixed and the next column starts to flash. Fill the next column the same way.
ENGLISH RT (RADIO TEXT) PS (Program Service Name) Frequency PTY AUTO SEARCH Your unit is equipped to automatically search for stations transmitting any of 29 different programme types. To search for a PTY, follow these procedures: 2. AV PRE TUNER AV8003 UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR VOLUME SURROUND MODE AUTO PURE DIRECT STANDBY ZONE ZONE SPEAKER MENU EXIT 7.1CH INPUT THX BAND TOP T-MODE M-DAX MEMORY CLEAR DISPLAY POWER ON/OFF PHONES SETUP MIC ENTER 1.3.4. 2.
ENGLISH NAMES AND FUNCTION ZONE PLAYBACK USING THE SURROUND BACK PREOUT TERMINALS This unit allows you to connect another set of power amp and place them in a different ZONE or separated area for Iistening to music. CONNECTIONS 3. 1. 4. AV PRE TUNER AV8003 UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR SURROUND MODE STANDBY VOLUME AUTO PURE DIRECT ZONE ZONE SPEAKER MENU EXIT 7.
Switch the remote controller to ZONE-A or ZONE-B mode. ZONE Speakers can be controlled on the first page of the remote controller. 3. Press the ENTER button. Once settings are complete, the Send indicator flashes twice. OSD INFORMATION DISPLAY ON THE ZONE MONITOR The following buttons are used for set ZONE mode or ZONE Speaker mode only. The setting status of ZONE A can be displayed on a TV monitor connected to the video output for ZONE (ZONE OUT) terminals. POWER ON/OFF 2.
ENGLISH NAMES AND FUNCTION REMOTE CONTROLLER OPERATION GENERAL INFORMATION OF RC2001 TO THE UNIT To control the unit by your RC2001, you have to select the device AMP, NETWORK or TUNER by pressing the function selector in HOME mode. Please refer below for the details in AMP, NETWORK and TUNER mode. CONNECTIONS Note: Except for some buttons, soft buttons result in the same operation as pressing either the Left or Right buttons for each command.
2 A/D AUDIO 1-HDMI-2 LIP SYNC AMP - BASS + 3 -TREBLE+ RE-EQ NIGHT EQ AMP TEST TONE CH SELECT 4 -CH LEV+ ATT VIDEO OFF AMP AUTO SURR 5 STEREO P DIRECT THX M-CH ST OFF. SELECT ANALOG/DIGITAL SELECT AUDIO mode (Left) SELECT HDMI OUTPUT 1* (Right) SELECT HDMI OUTPUT 2* Selects the LIP.SYNC mode (Left) BASS -* (Right) BASS +* (Left) TREBLE -* (Right) TREBLE +* RE-EQ ON/OFF NIGHT mode ON/OFF SELECT EQ mode Select TEST TONE menu Call up SETUP MENU and adjusts speaker levels or 7.
ENGLISH NAMES AND FUNCTION NETWORK MODE TUNER MODE CONNECTIONS SETUP Soft button HOME GUIDE INFO Cursor ENTER MENU EXIT CH +/2 4/¢ 9 ; 0-9 Blue Red Green Yellow Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode. Scroll the page Move to top of NETWORK page Used for displaying file details, etc. Used for moving the cursor, etc. Used for item selection, etc. Enter the Tool menu Used to return to the previous page, etc.
ENGLISH 1 2 3 4 0 ANGLE SUBTITLE AUDIO 1.DVD ZOOM SETUP VIDEO ADJ V ON/OFF DIMMER 1.DVD PROGRAM REPEAT A-B RANDOM COND MEMO 1.DVD SOUNDMODE SEARCH SCAN PAGE HDMI 1.
ENGLISH NAMES AND FUNCTION CONTROLLING A DSS (DSS MODE) CONTROLLING A MARANTZ CD PLAYER (CD MODE) CONNECTIONS SETUP BASIC OPERATION SOURCE ON/OFF Soft button HOME GUIDE INFO Cursor ENTER MENU EXIT INPUT PREV CH + / 2 4/¢ 0 9 ; 0-9 CLEAR Turns the DSS on and off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode. Scroll the page Move to TOP MENU.
Turns the UNIVERSAL DOCK (Dock connector) ON and OFF Turns the UNIVERSAL DOCK (Dock connector) ON Turns the UNIVERSAL DOCK (Dock connector) OFF Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode.
ENGLISH NAMES AND FUNCTION CONTROLLING A MARANTZ TV (TV MODE) List of Soft buttons CONNECTIONS SETUP SOURCE ON/OFF POWER ON POWER OFF Soft button HOME GUIDE INFO Cursor ENTER MENU EXIT MUTE INPUT PREV VOL +/CH +/0-9, +10 CLEAR Turns the TV on and off Turns the TV on Turns the TV off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode. Scroll the page Display Programmable TV menu OSD On/Off Move cursor on menus, etc. Confirm selection on menus, etc.
Page Command 9.TAPE 5/6 1 2 TAPE-A TAPE-B REC MUTE DIRECTION 9.TAPE COUNT RST AMS BLANKSKIP TIME TRAY Note Select TAPE function (left) REWIND* (Right) FAST FORWARD* Select TAPE DECK A Select TAPE DECK B Insert blank during recording AUTO REVERSE DIRECTION Select TAPE function COUNT RESET AUTO MUSIC SCAN Searches for an empty part TIME DISPLAY mode TRAY OPEN/CLOSE CONNECTIONS Turns the VCR on and off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode.
ENGLISH NAMES AND FUNCTION CONTROLLING A MARANTZ PLASMA (PLASMA MODE) List of Soft buttons CONNECTIONS POWER ON POWER OFF Soft button HOME INFO Cursor ENTER MENU EXIT MUTE INPUT VOL +/- Turns the PLASMA on Turns the PLASMA off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode. Scroll the page OSD On/Off Move cursor on menus, etc. Confirm selection on menus, etc.
1 2 1 2 3 Command MD Note 5/6 (left) REWIND* (Right) FAST FORWARD* TRAY OPEN/CLOSE Select INPUT SOURCE Select AUTO MARKER SYNCRO REC 0 INPUT MARKER SYNC REC MD PROGRAM RANDOM REPEAT EDIT SP/LP MD TIME CHAR PROGRAM RANDOM PLAY REPEAT PLAY Select EDIT mode Select SP/LP mode Select TIME mode Select CHARACTER mode OTHERS TROUBLESHOOTING 3 0 INPUT TR INCR SYNC REC CD-R PROGRAM RANDOM REPEAT A-B INTRO SCN CD-R DISPLAY BLANK SCROLL Page BASIC OPERATION 5/6 Note Select CD function (Left) REWIND (R
ENGLISH NAMES AND FUNCTION CONTROLLING A MARANTZ BLU-RAY PLAYER (BLU-RAY MODE) CONNECTIONS SETUP POWER ON POWER OFF Soft button HOME GUIDE INFO Cursor ENTER MENU EXIT 2 4/¢ 9 ; 0-9 CLEAR BLUE, RED, GREEN, YELLOW Turns the Blu-ray player on Turns the Blu-ray player off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode.
Note: Soft buttons on Page 5 and the 2, 4, ¢, 9, and ; buttons are only used for the NETWORK function. Page 1 Command ZONE-A Z.SPK-ON Z.
ENGLISH NAMES AND FUNCTION ZONE B (ZONE-B MODE) CONNECTIONS SETUP SOURCE ON/OFF POWER ON POWER OFF Soft button HOME INFO Cursor ENTER EXIT MUTE VOL + / 2 4/¢ 9 ; Turn the ZONE B on and off Turn the ZONE B on Turn the ZONE B off Refer to the list of soft buttons in the table below. Switch the remote controller to HOME mode. Scroll the page OSD information on/off Used to move the cursor, etc. Used to select items, etc. Used to return to the previous screen, etc.
Press the Home button to enter Home mode for the RC2001. Each time the button is pressed, the sleep setting time changes in the cycle shown below. 2. 3. Select the devices that are set in Home mode. PROCEED? 4. To control another device, return to Home mode and select another device. Perform operation of the device that you want to control in the selected device mode. The preinstalled default user file is used to control Marantz products.
ENGLISH NAMES AND FUNCTION 4. This screen changes to HOME mode. Press the button next to the displayed device name whose commands you want to learn. 6. This enters the learning standby mode. Press the remote controller button that you want to have learn the command. Hold down the button until “LEARN OK” is displayed on the remote controller’s LCD. CONNECTIONS Send the remote controller code that you want to learn. • The RC2001 can learn up to a maximum of 1,000 remote controller codes.
Operation Settings The timer function of the RC2001 can be used to send a preset remote controller command at a programmed time. The Wizz.it 3 editor can be used to operate multiple devices. One Touch Operation (Macro) can also use the timer function for transmission. 1. Press the button next to the “TIMER SET” indicator in the LCD in the TIMER menu screen to display the timer programming setting screen. SETUP • The timer settings are displayed. Check that the settings are correct.
ENGLISH NAMES AND FUNCTION Operation ON/OFF Settings 1. Press the button next to the “ON/OFF” indicator in the TIMER menu screen on the LCD to display the timer operation ON/OFF setting screen. • Either press the ENTER button or wait three seconds for the LCD to automatically return to the MAIN menu. • When timer operation is set to ON, the timer icon is displayed in the Sub Info area of the LCD.
3. • Either press the ENTER button or wait three seconds for the LCD to automatically return to the SYS.SETUP menu. The message “COMPLETED” is displayed in the LCD to indicate that the clock setting is completed. • Pressing the Home button returns the LCD to the MAIN MENU. 2. Press the buttons (right: +, left: -) displayed next to TIME to set the illumination time. The time can be set in 1-second intervals from 0 to 60 seconds. After deciding the settings, press the ENTER button.
ENGLISH NAMES AND FUNCTION LCD (LCD setting) Press the button next to the “LCD” indicator in the SYS.SETUP menu screen in the LCD. The LCD setting menu is displayed. 3. The message “COMPLETED” is displayed on the LCD to indicate that the display time setting is completed. • CONTRAST (LCD CONTRAST ADJUSTMENT) This enables the LCD contrast to be adjusted. Adjust for maximum visibility according to your viewing environment. 1. CONNECTIONS 2.
1. 2. Note: The LEARNING and CLOCK settings are not initialized. Press the button next to the “MEM CLEAR” indicator in the SYS.SETUP menu screen in the LCD to display the initialization setting screen. 4. STATUS INDICATOR 5. RESET This displays the settings made in the MAIN MENU and the status of the remote device. If the RC2001 is not operating properly, use the procedure below to perform a reset (restart). Performing a reset does not erase the settings in the RC2001. Checking the status 1.
ENGLISH NAMES AND FUNCTION GENERAL INFORMATION OF RC101 TO THE UNIT CONTROLLING MARANTZ COMPONENTS The included remote controller can be used in zone systems. Using this remote controller, you can operate the unit through infrared receivers or the infrared receptor of Marantz products in multiple ZONEs. 1. 2. Press the desired SOURCE button. Press the desired operation buttons to play the selected component. • For details, refer to the component’s user guide.
Moves the cursor for setting in DVD menu Play Stop Pause Skips to forward chapter/track Skips to previous chapter/track Searchs forward Searchs backward DVD changer next disc (*) Reserve for learinig Reserve for learinig Reserve for learinig Reserve for learinig • (*) RC101 dose not have the PRESET code library for this key. SOURCE ON/OFF MENU/INPUT CH3/4 ENTER 3(CURSOR) 4(CURSOR) 2(CURSOR) 1(CURSOR) 2 9 ; § ∞ 6 5 DISC+/T.
ENGLISH NAMES AND FUNCTION CONNECTIONS CONTROLLING A MARANTZ CD PLAYER (CD) CONTROLLING A MARANTZ CD RECORDER (CDR) CONTROLLONG A MARANTZ TAPE DECK (TAPE) • (*) RC101 dose not have the PRESET code library for this key. • RC101 dose not have the PRESET code library for this device. • RC101 dose not have the PRESET code library for this device. SETUP BASIC OPERATION ADVANCED OPERATION SOURCE ON/OFF MENU/INPUT CH3/4 ENTER 3(CURSOR) 4(CURSOR) 2(CURSOR) 1(CURSOR) 2 9 ; § ∞ 6 5 DISC+/T.
ENGLISH Each time press the buttons, illuminate button 2 seconds. To turn off back light, press and hold down the SET and 4 button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ¢ button until SEND indicator blinks twice. Initial is back light ON. 1. 1. Press and hold down the SOURCE button (ex TV) for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flashes.
ENGLISH NAMES AND FUNCTION LEARN MODE 4. CONNECTIONS This remote controller is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer. The receiver sensor for the remote control signals is located at the top of the remote controller.
ENGLISH Then back lights tune off. R LLE RO NT CO TE MO RE EM ST SY Do not touch either of the remote controls during the copying operation. Doing so could cause copying to fail. ST SY EM TE MO RE CO LLE RO NT R 2. When copying is started, the SEND indicator of transmitting remote controller and the LEARN indicator of receiving remote controller start to blink. When the copying operation is completed, the back lights of transmitting remote controller and receiving remote controller are turned on.
ENGLISH NAMES AND FUNCTION SETUP CODES (RC101) TV CONNECTIONS SETUP BASIC OPERATION ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING Acer ...................................................................................1141 Admiral ......................................................... 1002, 1009, 1089 Aiko................................................................................... 1059 Aiwa ......................................................................... 1117, 1118 Akai.........
CONNECTIONS SETUP BASIC OPERATION Alphastar .......................................................................... 4027 BSB .................................................................................. 4021 Chaparral .......................................................................... 4039 DIRECTV ................................................................ 4001, 4016 DISH Network ................................................................... 4030 Drake .............................
ENGLISH NAMES AND FUNCTION TROUBLESHOOTING SYMPTOM Can not select EX/ES mode. In case of trouble, check the following before calling for service: CONNECTIONS 1. 2. 3. Are the connections made properly ? Are you operating the unit properly following the user’s guide ? Are the power amplifiers and speaker working properly ? SETUP This unit cannot be turned up. CAUSE The power plug is not connected. REMEDY Connect the power plug to the outlet. Cancel mute using the remote controller.
The HDMI output on the source Set HDMI output so that it turns on, as explained in the component (DVD, Set Top Box, etc.) is source component's instruction manual. not on. The HDMI mode is not correctly set on Set HDMI input on the FUNC INPUT SETUP menu as the unit. explained on page 23. The HDMI output video resolution of the Set the resolution so that it matches, as explained in source component (DVD, Set Top Box, etc.) the instruction manuals of both components. does not match the TV specifications.
ENGLISH TECHNICAL SPECIFICATIONS AM TUNER SECTION ACCESSORIES DIMENSIONS Remote Controller RC2001 ........................................... 1 Remote Controller RC101 ............................................. 1 Microphone .................................................................... 1 AAA-size alkaline batteries ............................................ 4 AAA-size dry batteries ................................................... 2 FM Antenna ..............................................
THX® is an exclusive set of standards and technologies established by the world-renowned film production company, Lucasfilm Ltd. THX resulted from George Lucas’ desire to reproduce the movie soundtrack as faithfully as possible both in the movie theater and in the home theater. THX engineers developed patented technologies to accurately translate the sound from a movie theater environment into the home, correcting the tonal and spatial errors that occur.
ENGLISH NAMES AND FUNCTION CONNECTIONS The no compromise DTS digital process sets the standard of quality for cinema sound by delivering an exact copy of the studio master recordings to neighborhood and home theaters. Now, every moviegoer can hear the sound exactly as the moviemaker intended. DTS can be enjoyed in the home for either movies or music on of DVD’s, LD’s, and CD’s. SETUP BASIC OPERATION • dts Neo:6® The advantages of discrete multichannel systems over matrix are well known.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories. AV8003N.indb 87 HDCD® (High Definition Compatible Digital ®) is a patented process for delivering on Compact Disc the full richness and details of the original microphone feed. HDCD encoded CDs sound better because they are encoded with 20-bits of real musical information as compared to 16-bits for all other CDs.
www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark. Printed in China AV8003N.indb 2 04/2008 541110072038M mzh-d 08.4.