User's Guide
8
ENGLISH
ENGLISH
NAMES AND FUNCTIONS OF PARTS
FRONT PANEL
q POWER ON/OFF Switch
This switch turns power to the PM-11S1 ON and OFF. When
pressed, power is activated and the blue indicator on the
display w lights up. Approximately 8 seconds after power
is activated, audio output is enabled. Pressing the switch
again turns power OFF.
w Display
The display displays the selected input source, volume level
and setting status.
e INPUT SELECTOR Knob
This knob is for selecting the input source to use in play-
back and recording. The selected input source is displayed
on the display w.
r VOLUME Knob
This knob is for setting the volume. The volume level is
displayed on the display w. Turning the knob clockwise
increases the volume, while turning it counterclockwise de-
creases the volume. When turned slowly, the volume can
be fine-adjusted in 0.5 dB steps, whereas when turned
rapidly, volume level changes greatly.
t Infrared Receptor Window
This is the receptor of control signals sent from the included
RC-11PMS1 remote controller. Point the remote controller
towards this window to properly send signals.
y PHONES Jack
This jack is for connecting headphones with a standard
stereo plug. To listen with headphones, turn speaker out-
put OFF by setting the SPEAKER A and B buttons in the
OFF position.
u DISPLAY Button
This button turns the display and side illumination ON and
OFF. The button performs two functions depending on how
long it is pressed.
If pressed and held for 3 seconds or longer:
Turns the side illumination !4 on both sides of the display
ON and OFF. This operation sets the always-ON mode of
the side illumination, therefore once the side illumination
is turned OFF, it stays OFF and does not light even if power
is shut OFF and reactivated. To turn the side illumination
ON again, press and hold the DISPLAY button for 3 sec-
onds or longer.
If pressed and held for less than 3 seconds:
Turns the display ON and OFF. When the always-ON mode
is engaged for the side illumination, the side illumination
turns ON and OFF in synch with the display.
If the display is out and the VOLUME knob or other control
is operated, the display lights up. It will automatically go
out 3 seconds after the operation has been completed.
For instructions on how to operate the side illumination,
see “HOW TO OPERATE THE SIDE ILLUMINATION” on
pg. 16.
i TONE Button
This button turns the bass and treble tone control ON and
OFF. When tone control is ON, the center of the button is lit
a blue color. For instructions on how to adjust bass and
treble, see “How to Trim Bass” and “How to Trim Treble”
on pg. 18.
o SPEAKER A/B Buttons
These buttons turn the speaker output to the speakers
connected to the SPEAKER SYSTEM A/B terminals on
the rear panel ON and OFF. When speaker output is ON,
the center of the button is lit a blue color. To listen with
headphones, turn speaker output OFF.
!0 ATT Button
This button attenuates volume with one press of the but-
ton. When pressed, “AT T” flashes on the display and the
volume is reduced. If pressed again, the mode is canceled
and the original volume level is restored. Attenuation level
is set to –20 dB when the PM-11S1 is shipped from the
factory, but it can be set to either –40 dB or -∞ (mute). For
instructions on how to set attenuation level, see “How to
Set Attenuation Level” on pg. 16.
INTEGRARED AMPLIFIER PM-11S1
POWER ON/OFF
PHONES
VOLUME
A
TONE
SPEAKER
B
SPEAKER
REC OUT
PRE OUT
ATT.
MC
OPERATE
PHONO
DISPLAY
SELECTOR
INPUT
PM-11S1UENG(P07-P22)A4 04.10.15, 4:05 AMPage 8 AdobePageMaker6.5J/PPC