Model PM-11S3 Owner’s Manual Integrated Amplifier 1.PM-11S3U_ENG_0521.
1.PM-11S3U_ENG_0521.
ENGLISH FRANÇAIS ESPAÑOL n SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ESPAÑOL nnNOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO WARNINGS AVERTISSEMENTS ADVERTENCIAS • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. • Handle the power cord carefully. Hold the plug when unplugging the cord. • Keep the unit free from moisture, water, and dust. • Unplug the power cord when not using the unit for long periods of time. • Do not obstruct the ventilation holes. • Do not let foreign objects into the unit.
ENGLISH Contents Accessories·····················································································1 About this manual·········································································1 Cautions on handling·····································································2 About the remote control ····························································2 Inserting the batteries···································································2 Operating range of the remote cont
ENGLISH Cautions on handling • Before turning the power on Check once again that all connections are correct and that there are no problems with the connection cables. • Power is supplied to some of the circuitry even when the unit is set to the standby mode. When going on vacation or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.
ENGLISH HDAM®SA3 Module Constant Current Feedback Phono Equalizer Linear Control Volume The control knob had adopted the high-end model design concept. For better S/N ratio, the MAS6116 from Micro Analog Systems and the HDAM®SA3 have been combined, which enables smooth adjustment in the range of 0 to -100 dB in units of ±0.5 dB.
ENGLISH Part names and functions For buttons not explained here, see the page indicated in parentheses ( ). Front panel Rear panel Q6 Q4 Q5 Q1 Q4 Q3 o Q0 INTEGRATED AMPLIFIER PM-11S3 DISPLAY ATT. 3 2 3 1 2 1 PRE OUT TONE STANDBY SPEAKERS A P.
ENGLISH Remote control nnButtons for amplifier nnButtons for Super Audio CD player q u r t y Q9 t y u i o W0 u w o Q0 Q0 Q1 Q2 Q3 W1 Q9 Q4 u W2 W3 W4 Troubleshooting Q5 Q6 Q7 Q8 Explanation terms NOTE The remote control may not operate some products. Advanced operation i • The supplied remote control can be used to control marantz Integrated Amplifier and marantz Super Audio CD player. • When using this remote control, also refer to the operating instructions of the other devices.
ENGLISH Basic connections NOTE • Do not plug in the power cord until all connections have been completed. • When making connections, also refer to the operating instructions of the other components. • Be sure to connect the left and right channels properly (left with left, right with right). • Do not bundle power cords with connection cables. Doing so can result in humming or noise. • Do not turn up the volume without a turntable connected to the PHONO input terminals. Doing so will cause humming or noise.
ENGLISH Connecting the speakers cables Spade lug connector Speakers used A B A and B Bi-wiring Connection off about 0.03 ft / 10 mm of 1 Peel sheathing from the tip of the speaker 2 Protection circuit When using a banana plug Explanation terms NOTE • Connect the speaker cables so they do not stick out of the speaker terminals. The protection circuit may be activated if the wires touch the rear panel or if the + and – sides touch each other (vpage 21 “Protection Circuit”).
ENGLISH Connecting the speakers Speaker connections Bi-wiring connection • The same signal is output from the SPEAKER A and B terminals. • When only one set of speakers is to be connected, use either the SPEAKER A or B terminals. • When bi-wiring with bi-wireable speakers, connect the mid and high range terminals to SYSTEM (A) (or SYSTEM (B)), the low range terminals to SYSTEM (B) (or SYSTEM (A)).
ENGLISH nnBALANCED Jacks Super Audio CD player Turntable The XLR connector for professional use is internally wired in either of the following two systems. • USA system (w PIN=COLD e PIN=HOT) L R 3 2 3 1 2 1 COLD Tuner 3 2 AUDIO 3 1 2 1 2 HOT 3 1 GND Advanced connections Connect the ground wire from your turntable here.
ENGLISH Connecting recorders Connecting the power cord Recorder-1 Recorder-2 AUDIO AUDIO AUDIO IN AUDIO IN AC IN L L L L L L R R R R R R L L L L L L R R R R R R 3 2 Do not plug in the power cord until all connections have been completed. 3 1 2 1 AUDIO OUT AUDIO OUT To household power outlet (AC 120 V, 60 Hz) Power cord (supplied) NOTE Insert the plugs securely. Loose connections will result in the generation of noise. 10 1.PM-11S3U_ENG_0521.
ENGLISH Before use Starting playback Turning the power off Press X ON/OFF on the unit. Press X ON/OFF on the unit. Press X AMP. CD LINE-1 LINE-2 BALANCED RECORDER1 PHONO RECORDER2 3 Start playing back the source. the VOLUME df on the unit or remote 4 Adjust control to the desired level. Explanation terms NOTE Power continues to be supplied to some of the circuitry even when the power is in the standby mode.
ENGLISH Starting playback Adjusting the levels Adjusting the tone nnLeft and right channel balance nnLow frequency range nnHigh frequency range 1 Press MENU. 1 Press MENU. 2 Press ENTER. 2 Press ENTER twice. 3 Press df to adjust the level. 3 Press df to adjust the level. The volume level of the left and right channels can be trimmed in 0.5 dB steps across a 0.0 – 9.0 dB range. When the unit is shipped from the factory, the volume level is set to 0.0 dB (maximum). 1 Press MENU.
ENGLISH Muting the sound Sound can be muted temporarily. “ATT” appears on the display and the sound is muted. Plug headphones into PHONES jack. • When using headphones, turn off the speaker output using SPEAKERS A/SPEAKERS B. • To prevent hearing loss, do not raise the volume level excessively when using headphones. Switching the illumination lamp setting The illumination lamps on the both sides of the unit main panel can be turned on or off. Press and hold DISPLAY on the unit for 2 seconds or longer.
ENGLISH Advanced connections F.C.B.S. connection The marantz F.C.B.S. (Floating Control Bus System) is the high quality sound system for link control between multiple PM-11S3 units (up to 4 units). Each unit is controlled via its ID number registered beforehand. The ID numbers need to be set to an operating unit (master) and a subordinate unit (slave) receiving the command from the master. For slave units, register ID numbers in the order of command reception from the master.
ENGLISH nnHow to set ID number for F.C.B.S. When the unit is turned on, the display shows the ID number for three seconds. Basic connections For a master unit, ID number 1 needs to be assigned. For a slave unit, set any of ID numbers 2 to 4. 1 While holding DISPLAY on the unit, press X ON/OFF. 2 Turn INPUT SELECTOR on the unit to select an ID number. DISPLAY INTEGRARED AMPLIFIER PM-11S3 ATT. PRE OUT TONE P.
ENGLISH F.C.B.S. connection Stereo complete bi-amp connection This mode enables the two amplifiers connected to this unit to function as one monaural amplifier. To use this mode, two F.C.B.S. connected PM-11S3 units are required. To switch the mode, use the amplifier mode switch on the rear panel while the power is off.
ENGLISH Connection for 5.1 Multi-channel Playback Basic connections The three units are connected using F.C.B.S. For the F.C.B.S connection, prepare 3 audio connection cables, and refer to F.C.B.S. ( vpage 14). Connect the outputs of players that have 5.1 channel analog outputs to each of the three units. If using an active subwoofer, see the instruction manual that came with the subwoofer for further instructions. Set the ID numbers for the three amplifiers as explained in How to set ID number for F.C.
ENGLISH F.C.B.S. connection nnSpeaker Positioning for Super Audio Multichannel Sound In order to enjoy Super Audio CD multi-channel sound with the best possible acoustics, it is recommended to position speakers as specified in ITU-R BS.775-1 of the International Telecommunication Union (ITU). Super Audio CD multichannel discs are recorded and mixed so as to achieve the optimum effect with a speaker system laid out as specified in ITU-R BS.775-1.
ENGLISH Connecting pre out connectors • The power direct mode setting changes with each press of the button. Power-amplifier Off (Factory default) On R To input connectors Speakers (L) Advanced connections Pre-amplifier L Basic operation • If the mode is set to on, the display shows “POWER AMP DIRECT”. On: Allows the device connected to the Power Amp Direct connector to be played. Off: Allows the program source selected using INPUT SELECTOR to be played.
ENGLISH Connecting the remote control connectors When you use this unit connected to marantz audio components, it sends control signals to operate each component. nnConnection Use the remote connection cable (supplied with a marantz audio component you want to connect) to connect the REMOTE CONTROL OUT terminal of this unit to the REMOTE CONTROL IN terminal of the component to be connected.
ENGLISH At power on For about 8 seconds after the power is turned on, the protection circuit is activated, muting the sound to give the amplifier circuits time to stabilize. Once the amplifier circuits stabilize, the protection circuit is released, and audio is enabled. In the event of overcurrent In the event of amplifier trouble The protection circuit is activated, and the power is automatically shut OFF, if an abnormality is detected in the power circuit.
ENGLISH Troubleshooting nnError messages When multiple amplifiers are connected by F.C.B.S., the error messages described in the table below may be displayed on the display. In such a case, ID number setting or remote cable connection may be in failure. Check the ID number or remote cable connection, referring to the table below. For details on ID number setting, see “How to set ID number for F.C.B.S.” (vpage 15). 1 Indication ERROR 02 Meaning Multiple amplifiers take ID No. 2.
ENGLISH 9 • Connect securely. 9 • Try changing the positions in which the devices are installed. – • Install the player and speakers as far from each other as possible. • Use cushions, etc., to absorb the speakers’ vibrations. – • Adjust to a proper needle pressure. • Check the tip of the needle. • Replace the cartridge. • Replace the batteries with new ones. • Operate closer to the unit. – – – 2 2 • Remove the obstacle. – • Confirm the correct button to press.
ENGLISH Specifications • RMS Power output: (20 Hz - 20 kHz 2-channel simultaneously driven) • Total harmonic distortion: (20 Hz - 20 kHz 2-channel simultaneously driven, 8 Ω) • Output band width: (8 Ω, 0.05 %) • Frequency response: (CD, 1 W, 8 Ω load) • Damping factor: (8 Ω, 20 Hz − 20 kHz) • Input sensitivity/Input impedance PHONO (MC): PHONO (MM): BALANCED: CD/LINE: P.
Dimensions / Dimensions / Dimensions 3/4 (18.0) 5-3/4 (146.0) 6-5/8 (168.0) 17-3/8 (440.0) 3/16 (4.0) 3/4 (19.0) 15-3/4 (400.0) 17-7/8 (453.0) 1-3/8 (34.0) Unit / Unité / Unidad : inch (mm) Weight / Poids / Peso : 58 lbs 10 oz (26.6 kg) 4.PM-11S3U_BackPage_0521.
D&M Holdings Inc. Printed in China 5411 10897 00AM V00 4.PM-11S3U_BackPage_0521.
