Contents Connections Playback Settings Tips Appendix Integrated Amplifier PM8005 You can print more than one page of a PDF onto a single sheet of paper.
Contents Connections Playback Settings Tips Appendix Contents Connecting a playback device···················································· 19 Connecting a recording device··················································· 20 Connecting amplifiers··································································· 21 Connecting devices with remote control connectors········· 22 Accessories························································································· 4 Inserting the bat
Contents Connections Playback Settings Settings Setting the Auto Standby mode················································ 30 Turning Auto Standby mode on······················································ 30 Turning Auto Standby mode off······················································ 30 Setting the power amp direct mode········································ 31 Turning power amp direct mode on················································ 31 Turning power amp direct mode off···········
Contents Connections Playback Settings Appendix Tips Thank you for purchasing this Marantz product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference. Accessories Check that the following parts are supplied with the product.
Contents Connections Playback Settings Inserting the batteries Appendix Tips Operating range of the remote control unit Point the remote control unit at the remote sensor when operating it. q Remove the rear lid in the direction of the arrow and remove it. Approx. 23 ft/7 m w Load the two batteries properly as indicated by the q and w marks in the battery compartment. R03/AAA batteries 30° e Put the rear cover back on.
Contents Connections Playback Settings Tips Appendix Features • Short-power-line layout For strong momentary current supply, a short power-line layout unifies the power circuit and output stage of the power amplifier section. This layout allows connecting the large-current lines via the shortest route while to arranging the left and right channels symmetrically.
Contents Connections Playback Settings • Double-shielded triodal transformer The unit is equipped with a toroidal power transformer to minimize vibration and leakage flux specific to the transformer. Especially to reduce leakage flux, which affects sound quality, the periphery is doubleshielded, using a core ring and a short ring. • Tri-tone control This unit is equipped with a tone control function that enables adjustment of the strength of the mid range as well as the low and high ranges (vpage 26).
Contents Connections Playback Settings Appendix Tips Part names and functions Front panel Q4 Q5 q w e r q Power indicator This is lit as follows according to the power status : • Power on : Off • Standby : Red • Power off : Off • When the protection circuit is activated : Red (blinking) t y Q3 Q1 u i o Q0 e Headphone jack (PHONES) Used to connect headphones. Turn off speaker output when using headphones (vpage 26).
Contents Connections Q5 Q4 Playback Q3 Settings Tips Appendix Q1 Remote control sensor Q2 This receives signals from the remote control unit (vpage 5). Q2 VOLUME control knob This adjusts the volume level (vpage 26). Q3 MUTE indicator This lights while the sound is muted (vpage 26). Q4 Input indicator (vpage 26) Q5 Input source select knob (INPUT SELECTOR) r t y u i o Q0 Q1 This selects the input source (vpage 26). r BASS control knob NOTE This adjusts the bass (vpage 26).
Contents Connections Playback Settings Tips Appendix Rear panel Q3 Q2 Q1 Q0 q w e r t q CD input connectors o y u i t Recorder input connectors (RECORDER) Used to connect a CD player (vpage 19). Used to connect the output connector of a recorder (vpage 20). w Network audio player input connectors (NETWORK) y Recorder output connectors (RECORDER) e AUX input connectors u Speaker system terminals (SPEAKERS) Used to connect a network audio player (vpage 19).
Contents Connections Playback Settings o Q3 Q2 Q1 Q0 i i Remote control input/output connectors (REMOTE CONTROL) Used to connect to a Marantz audio device that is compatible with the remote control function (vpage 22). o AC inlet (AC IN) Used to connect the power cord (vpage 23). Q0 Power amplifier direct connectors (POWER AMP DIRECT IN) Used to connect a pre-amplifier when this unit is used as a power amplifier (vpage 21).
Contents Connections Playback Settings Tips Appendix Remote control unit Amplifier operations r q Input source select buttons These select the input source (vpage 26). w SOURCE DIRECT button q This turns SOURCE DIRECT mode on/off (vpage 27). e MUTE button ( ) This mutes the audio (vpage 26). r AMP POWER button (X) This turns the power on/off (standby) (vpage 25). w t t VOLUME buttons (df) These adjust the volume level (vpage 26).
Contents Connections Playback Settings Tips Appendix CD player operations To operate Marantz CD player, press REMOTE MODE CD button to switch the remote control to the CD operation mode. • REMOTE MODE CD button lights for approximately two seconds.
Contents Connections Playback Settings Tips Appendix Network audio player operations To operate Marantz network audio player, press REMOTE MODE NET button to switch the remote control to the NETWORK operation mode. • REMOTE MODE NET button lights for approximately two seconds.
Contents Connections Playback Settings Tips Appendix Connections 22Cables used for connections Speaker connection (vpage 16) Provide necessary cables according to the devices you want to connect.
Contents Connections Playback Settings Tips Appendix Speaker connection NOTE Connecting the speakers cables • Disconnect this unit’s power plug from the power outlet before connecting the speakers. • Connect so that the speaker cable core wires do not protrude from the speaker terminal. The protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each other (vpage 39 “Protection circuit”).
Contents Connections Playback Settings Appendix Tips Speaker A/B connection • The same signal is output from the SPEAKERS A and SPEAKERS B terminals. • When only one set of speakers is to be connected, use either the SPEAKERS A or SPEAKERS B terminals.
Contents Connections Playback Settings Appendix Tips Bi-wiring connection • When bi-wiring with bi-wireable speakers, connect the mid and high range terminals to SPEAKERS A (or SPEAKERS B), the low range terminals to SPEAKERS B (or SPEAKERS A). • This connection limits the effect of signal interference between the high range speakers and low range speakers, allowing you to enjoy high quality playback.
Contents Connections Playback Settings Tips Appendix Connecting a playback device You can connect Blu-ray disc players, turntables, CD players, network audio players and tuners to this unit. This unit is compatible with turntables equipped with a moving magnet (MM) phono cartridge. When you connect to a turntable with a low output moving coil (MC) cartridge, use a commercially available MC head amp or a step-up transformer.
Contents Connections Playback Settings Tips Connecting a recording device Recording device AUDIO OUT R L AUDIO IN R L R L R L R L R L NOTE • Never insert the short-circuiting pin plug into the recording output connectors (AUDIO OUT RECORDER). Doing so could result in damage.
Contents Connections Playback Settings Connecting amplifiers Power amplifier Preamplifier AUDIO IN R L AUDIO OUT R L R L R L R L R L NOTE • Never insert the short-circuiting pin plug into the PRE OUT terminals. Doing so could result in damage.
Contents Connections Playback Settings Tips Appendix Connecting devices with remote control connectors Performing operations by RC on this unit without visual contact Remotely connecting Marantz devices You can transmit remote control signals simply by connecting a Marantz audio device to the REMOTE CONTROL IN/OUT connectors using the remote connection cable provided with the device.
Contents Connections Playback Settings Tips Connecting the power cord Wait until all connections have been completed before connecting the power cord.
Contents Connections Playback Settings Tips Appendix Playback Turning the power on (vpage 25) Turning off the sound temporarily (vpage 26) Selecting the speakers for audio output (vpage 26) Adjusting the tone (vpage 26) Selecting the input source (vpage 26) Playing CDs (vpage 27) Adjusting the volume (vpage 26) Recording (vpage 28) Front panel Rear panel Remote 24 Index
Contents Connections Playback Settings Tips Appendix Turning the power on AMP POWER X 1 Input source select buttons Press X on this unit to turn the power on. Input indicator for the selected source lights. NOTE SOURCE DIRECT • Turn VOLUME on this unit to adjust the volume to the lowest level before turning on the power. VOLUME df 22Turning the power standby MUTE 1 Press AMP POWER X. The standby indicator lights red. % • Press AMP POWER X to turn on power from standby mode.
Contents Connections Playback Settings Selecting the speakers for audio output 1 Turning off the sound temporarily 1 Press SPEAKERS A/B to select the speaker system to be used for playback. The indicator of the selected speakers lights. Press MUTE • Muting can be cancelled by pressing MUTE • Press SPEAKERS A/B to turn the speaker audio output off, and the speaker switching indicator turns off. 1 Press the input source select button to be played back.
Contents Connections Playback Settings Tips Playing CDs 22Playback in source direct mode 1 2 1 The signal does not pass through the tone adjustment circuitry (BASS, MID, TREBLE and BALANCE), resulting in playback of a higher sound quality. Press X on this unit to turn the power on. Press the input source select buttons to switch the input source to “CD”. Press SOURCE DIRECT to turn on source direct mode. The SOURCE DIRECT indicator lights. The “CD” input indicator lights. 3 4 Playback the CD.
Contents Connections Playback Settings Recording 1 2 Press X on this unit to turn the power on. Press the input source select buttons to switch to the input source from which you want to record. The indicator of the selected input source lights. 3 Recording starts. • For information on operations, see the owner’s manual of the recording device.
Contents Connections Playback Settings Settings Setting the Auto Standby mode (vpage 30) Setting the power amp direct mode (vpage 31) Front panel Rear panel Remote 29 Index Tips Appendix
Contents Connections Playback Settings Tips Appendix Setting the Auto Standby mode You can set the unit to automatically switch to standby mode if the unit is not operated for 30 minutes when there is no audio input. Auto Standby mode is set to off by default. Turning Auto Standby mode on 1 SOURCE DIRECT Press and hold SOURCE DIRECT for more than 5 seconds to turn the Auto Standby mode on. The power indicator flashes three times.
Contents Connections Playback Settings Tips Appendix Setting the power amp direct mode When a pre-amplifier is connected to this unit and the unit is used as a power amplifier, follow the instructions below to turn power amp direct mode on. Turning power amp direct mode on 1 POWER AMP DIRECT Press and hold POWER AMP DIRECT for more than 3 seconds to turn the power amp direct mode on. The power amp direct indicator lights and the power amp direct mode turns on.
Contents Connections Playback Settings Tips Appendix Tips Contents 22Tips.....................................................................(33) 22Troubleshooting...............................................(34) I want to adjust the tone myself.......................................................(33) Power does not turn on/Power is turned off.....................................(34) I want sound playback that is faithful to the original sound..............
Contents Connections Playback Settings Tips Appendix Tips I want to adjust the tone myself • Use the BASS, MID, TREBLE and BALANCE knobs to adjust the sound as desired (vpage 26). I want sound playback that is faithful to the original sound • Set the Source Direct mode on (vpage 27). I want to operate a Marantz CD player or network audio player using the remote control of this unit • Switch the remote control operating mode (vpage 13, 14).
Contents Connections Playback Settings Tips Appendix Troubleshooting If a problem occurs, first check the following: 1. Are the connections correct? 2. Is the unit being operated as described in the owner’s manual? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. If the problem persist there may be a malfunction. In that case, disconnect the power immediately and contact your retail outlet.
Contents Connections Playback Settings Symptom Tips Appendix Cause / Solution Power turns off and the power • Due to the temperature rise within this unit, the protection circuit is working. Turn off the indicator flashes red approx. every 0.5 power and wait about an hour until this unit sufficiently cools down. Then, turn on the power seconds. again. • Please re-install this unit in a place having good ventilation. Page 39 – Power turns off and the power indicator flashes red approx. every 0.
Contents Connections Playback Settings Tips Appendix 22Operations cannot be performed through the remote control unit Symptom Operations cannot be performed through the remote control unit. Front panel Rear panel Cause / Solution Page • Batteries are worn out. Replace with new batteries. • Operate the remote control unit within a distance of about 23 ft/7 m from this unit and at an angle of within 30°. • Remove any obstacle between this unit and the remote control unit.
Contents Connections Playback Settings Tips Appendix 22No sound comes out Symptom No sound comes out of speakers. Front panel Rear panel Cause / Solution Page • Check the connections for all devices. • Insert connection cables all the way in. • Check that input connectors and output connectors are not reversely connected. • Check cables for damage. • Check that speaker cables are properly connected. Check that cable core wires come in contact with the metal part on speaker terminals.
Contents Connections Playback Settings Tips Appendix 22Desired sound does not come out Symptom Cause / Solution Page No sound comes out of a specific speaker. • Check that the speaker cable is properly connected. • Adjust the BALANCE control knob. 16 26 The left and right of stereo sound is reversed. • Check whether the left and right speakers are connected to the correct speaker terminals.
Contents Connections Playback Settings Tips Appendix Appendix Explanation terms Trademark information P Protection circuit This is a function to prevent damage to devices within the power supply when an abnormality such as an overload, excess voltage occurs or over temperature for any reason. If a malfunction occurs in this unit, the power indicator blinks red and the unit switches to standby mode.
Contents Connections Playback Settings Specifications • RMS Power output (20 Hz – 20 kHz simultaneous drive of both channels) : • Total harmonic distortion (20 Hz – 20 kHz simultaneous drive of both channels, 8 Ω/ohms load) : • Output band width (8 Ω/ohms load, 0.
Contents Connections Playback • S/N (IHF-A, 8 Ω/ohms load) PHONO (MM) : CD, TUNER, NETWORK, AUX, RECORDER : POWER AMP DIRECT IN : • Tone control Bass (50 Hz) : Mid (900 Hz) : Treble (15 kHz) : • Power requirement : • Power consumption (UL60065) : • Power consumption in standby mode : Settings 87 dB (5 mV input, 1 W output) 106 dB (2 V input, Rated output) 125 dB (Rated output) ±10 dB ±6 dB ±10 dB AC 120 V, 60 Hz 220 W 0.
Contents Connections Playback Settings Index vv A vv P Accessories······························································· 4 Adjusting the tone··················································· 26 BALANCE····························································· 26 BASS···································································· 26 MID······································································ 26 TREBLE································································ 26 Ad
Contents Connections Playback Settings Appendix Tips 1 19/64 (33) 22Dimensions 43/64 (17) 8 55/64 (225) 2 21/64 (59) 14 59/64 (379) 12 61/64 (329) 1 49/64 (45) Unit : in. (mm) 1 31/32 (50) 22Weight : 26 lbs 7 oz (12.
D&M Holdings Inc.
